Line 5: |
Line 5: |
| ==Data senders== | | ==Data senders== |
| | | |
− | [[File:{{{file_status}}}]] | + | [[File:{{{file_sender}}}]] |
| | | |
| 123 | | 123 |
Line 14: |
Line 14: |
| 123 | | 123 |
| | | |
− | [[File:{{{file_status}}}]] | + | [[File:{{{file_sender_settings}}}]] |
| | | |
| <table class="nd-mantable"> | | <table class="nd-mantable"> |
Line 23: |
Line 23: |
| </tr> | | </tr> |
| <tr> | | <tr> |
− | <td>Open collector output</td> | + | <td>Enabled</td> |
− | <td>Low level | High level; default: <b>Low level</b></td> | + | <td>off | on; default: '''off'''</td> |
− | <td>Changes the default<span class="asterisk">*</span> state of the open collector (OC) output pin.</td> | + | <td>Check to enable data sender</td> |
− | </tr>{{#ifeq:{{{name}}}RUT955| | + | </tr> |
| + | <tr> |
| + | <td>Name</td> |
| + | <td>Default:</td> |
| + | <td>Name of the data sender. Used for easier data senders management purposes only (optional)</td> |
| + | </tr> |
| <tr> | | <tr> |
− | <td>Relay output</td> | + | <td>Data source</td> |
− | <td>Contacts open <nowiki>|</nowiki> Contacts closed; default: <b>Contacts closed</b></td> | + | <td>Default: '''Bluetooth data'''</td> |
− | <td>Changes the default<span class="asterisk">*</span> state of the relay output pin.</td> | + | <td>Source of the data to be sent to server. Available options: |
− | </tr>|}} | + | |
| + | * '''Bluetooth data''' |
| + | * '''Modbus data''' |
| + | </td> |
| + | </tr> |
| + | <tr> |
| + | <td>Protocol</td> |
| + | <td>Default: '''HTTP(S)'''</td> |
| + | <td>Protocol used for sending the data to server. Available options: |
| + | |
| + | * '''HTTP(S)''' |
| + | * '''MQTT''' |
| + | </td> |
| + | </tr> |
| + | <tr> |
| + | <td>JSON format</td> |
| + | <td>Default: '''{"TS":"%t", "D":"%d","MAC":"%m","DT":"%b"}'''</td> |
| + | <td>You can fully customize JSON segment</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Segment count</td> |
| + | <td>Default: '''1'''</td> |
| + | <td>Max segment count in one JSON string sent to server. Available options: |
| + | |
| + | * '''1''' |
| + | * '''2''' |
| + | * '''3''' |
| + | * '''4''' |
| + | * '''5''' |
| + | * '''6''' |
| + | * '''7''' |
| + | * '''8''' |
| + | * '''9''' |
| + | * '''10''' |
| + | </td> |
| + | </tr> |
| + | <tr> |
| + | <td>URL/Host/Connection string</td> |
| + | <td>Default:</td> |
| + | <td>URL for HTTP(S); Host for MQTT; Connection string for Azure MQTT</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Period</td> |
| + | <td>Default: '''60'''</td> |
| + | <td>Interval for sending the collected data to server (in seconds, 1-86400)</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Data filtering</td> |
| + | <td>Default: '''All data'''</td> |
| + | <td>Choose which data this sender will send to server. Available options: |
| + | |
| + | * '''All data''' |
| + | * '''By slave ID''' |
| + | * '''By slave IP''' |
| + | * '''By MAC address''' |
| + | * '''By device name''' |
| + | </td> |
| + | </tr> |
| + | <tr> |
| + | <td>Retry on fail</td> |
| + | <td>off | on; default: '''off'''</td> |
| + | <td>In case of a failed attempt, retry to send the same data to server later (Retry until successful)</td> |
| + | </tr> |
| + | <tr> |
| + | <td>Custom header</td> |
| + | <td>Default:</td> |
| + | <td>Allows to add custom headers to the HTTP requests</td> |
| + | </tr> |
| </table> | | </table> |
| + | |
| + | [[Category:{{{name}}} WebUI]] |