Changes

Template talk:FMB CAN adapters (view source)

Revision as of 09:15, 3 April 2020

No change in size , 09:15, 3 April 2020

no edit summary

Line 1: Line 1: −

Easy steps to install and configure following CAN adapters on {{{model|~~FMC1YX~~}}} device:

+

Easy steps to install and configure following CAN adapters on {{{model|FMC125}}} device:

* [[LV-CAN200]]

* [[ALL-CAN300]]

Line 8: Line 8:

__TOC__

−

==Installing CAN adapter with {{{model|~~FMC1YX~~}}} device==

+

==Installing CAN adapter with {{{model|FMC125}}} device==

===Installing LV-CAN200/ALL-CAN300/CAN-CONTROL===

Line 15: Line 15:

* [[LV-CAN200]]/[[ALL-CAN300]]/[[CAN-CONTROL]]

* Connection scheme (Please contact Teltonika Sales Representative and provide information about '''vehicle manufacturer''', '''model''' and '''year'''.

−

* {{{model|~~FMC1YX~~}}} device

+

* {{{model|FMC125}}} device

* Pliers

* Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)

Line 24: Line 24:

# Be ready with a vehicle '''connection scheme''' that you have received from a Teltonika Sales Representative.

# '''Check the scheme''' for the current vehicle connection. Look for connectors matching '''PINs numbers''' and colors (may be different) according to connection scheme.

−

# Connect CAN adapter with {{{model|~~FMC1YX~~}}}:

+

# Connect CAN adapter with {{{model|FMC125}}}:

−

## Connect CAN adapter '''PIN 6''' '''(Rx)''' to '''INPUT 6''' of {{{model|~~FMC1YX~~}}}.

+

## Connect CAN adapter '''PIN 6''' '''(Rx)''' to '''INPUT 6''' of {{{model|FMC125}}}.

−

## Connect CAN adapter '''PIN 5''' '''(Tx)''' to '''INPUT 5''' of {{{model|~~FMC1YX~~}}}.

+

## Connect CAN adapter '''PIN 5''' '''(Tx)''' to '''INPUT 5''' of {{{model|FMC125}}}.

# Connect CAN adapter '''CAN wires (CAN L, CAN H)''' as specified in connection scheme.<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap CAN L and CAN H lines. Not all CAN adapter wires may be used in vehicle.</td></table>

−

# Connect CAN adapter '''positive''' and '''ground''' wires to the vehicle power supply lines or near {{{model|~~FMC1YX~~}}} power wires.<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap power supply lines. Make sure that voltage does not exceed 30V.</td></table>

+

# Connect CAN adapter '''positive''' and '''ground''' wires to the vehicle power supply lines or near {{{model|FMC125}}} power wires.<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap power supply lines. Make sure that voltage does not exceed 30V.</td></table>

# Switch vehicle '''ignition to ACC''' position. CAN adapter '''LED diode''' on the back should start '''blinking'''.

−

# Configure CAN adapter to read CAN bus data or control vehicle by setting its '''program number''' - [[{{{model|~~FMC1YX~~}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]

+

# Configure CAN adapter to read CAN bus data or control vehicle by setting its '''program number''' - [[{{{model|FMC125}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]

[[File:CAN_adapter_connection_example_updated.png|1000px|none|thumb|LV-CAN200/ALL-CAN300 connection example. This is not a connection diagram for your vehicle. Every vehicle has a specific scheme.]]

Line 42: Line 42:

* Connection scheme (Please contact Teltonika Sales Representative and provide information about '''vehicle manufacturer''', '''model''' and '''year'''.

* [[SIMPLE-CAN]] (Used for contactless connection. If '''two CAN lines''' need to be connected, '''two SIMPLE-CAN's''' must be used.)

−

* {{{model|~~FMC1YX~~}}} device

+

* {{{model|FMC125}}} device

* Pliers

* Quick splice connectors (If vehicle CAN bus wires are very thin CAN adapter wires should be connected directly)

Line 49: Line 49:

====Installation steps====

−

# Follow the same '''1, 2, 3''' installation steps as with [[{{{model|~~FMC1YX~~}}}_CAN_adapters#Installation_steps| LV-CAN200/ALL-CAN300/CAN-CONTROL installation]].

+

# Follow the same '''1, 2, 3''' installation steps as with [[{{{model|FMC125}}}_CAN_adapters#Installation_steps| LV-CAN200/ALL-CAN300/CAN-CONTROL installation]].

# Connect the appropiate CAN bus pair of wires between CAN adapter and [[SIMPLE-CAN]]:

#: If '''CAN1 line''' need to be connected as specified in connection scheme:

Line 58: Line 58:

## Connect CAN adapter '''CAN2 H''' to '''CAN H''' of [[SIMPLE-CAN]].<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap CAN L and CAN H lines. Not all CAN adapter wires may be used in vehicle.</td></table>

# Fasten [[SIMPLE-CAN]] '''between vehicle CAN bus wires''' according to the connection scheme. '''It doeasn't matter which wire is on which side.'''[[File:SIMPLE-CAN_connection.gif|none]]

−

# Connect CAN adapter '''positive''' and '''ground''' wires to the vehicle power supply lines or near {{{model|~~FMC1YX~~}}} power wires.<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap power supply lines. Make sure that voltage does not exceed 30V.</td></table>

+

# Connect CAN adapter '''positive''' and '''ground''' wires to the vehicle power supply lines or near {{{model|FMC125}}} power wires.<table><td>[[File:Alert.png|50px|left|link=]]</td><td>Do not swap power supply lines. Make sure that voltage does not exceed 30V.</td></table>

# Switch vehicle '''ignition to ACC''' position.

# [[SIMPLE-CAN]] '''LED will shine continously''' so device awaits for '''calibration'''.<div><ul><li style="display: inline-block;">[[File:SIMPLE-CAN_calibration.gif|none|thumb|'''Press the switch shortly''' and wait for the LED to start blinking '''every one second'''. ]]</li><li style="display: inline-block;">[[File:SIMPLE-CAN after calibration.gif|none|thumb|Automatic calibration process takes up to 10 seconds depending on the vehicle model. Device is calibrated properly then the LED is blinking '''every 2 seconds'''.]]</li></ul></div><table><td>[[File:Alert.png|50px|left|link=]]</td><td>If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.</td></table>

−

# Configure CAN adapter to read CAN bus data by setting its '''program number''' - [[{{{model|~~FMC1YX~~}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]

+

# Configure CAN adapter to read CAN bus data by setting its '''program number''' - [[{{{model|FMC125}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]

[[File:Can_adapter%2Bsimple-can_connection_example_updated.png|1000px|none|thumb|LV-CAN200/ALL-CAN300 + SIMPLE-CAN connection example. This is not a connection diagram for your vehicle. Follow LV-CAN200/ALL-CAN300 connection scheme suitable for your vehicle.]]

Line 71: Line 71:

CAN Adapter must be set to program number which depends on the vehicle model. '''Needed program number is always written on CAN Adapter mounting scheme.''' In order to be able to enter program number in adapter '''Software date of CAN adapter must be newer than connection scheme date'''.

CAN adapter Software date can be checked:

−

* Via [[{{{model|~~FMC1YX~~}}}_Status_info#CAN_Adapter_Info|Teltonika Configurator→Status→CAN Adapter]]

+

* Via [[{{{model|FMC125}}}_Status_info#CAN_Adapter_Info|Teltonika Configurator→Status→CAN Adapter]]

* Via SMS command - [[FMB_lvcangetinfo|lvcangetinfo]]

Line 81: Line 81:

----

Required conditions:

−

* CAN adapter properly connected to {{{model|~~FMC1YX~~}}} device

+

* CAN adapter properly connected to {{{model|FMC125}}} device

CAN adapter program number can be set remotely, using SMS command.

−

Send following '''SMS command''' to {{{model|~~FMC1YX~~}}} device:

+

Send following '''SMS command''' to {{{model|FMC125}}} device:

* If you have set SMS login and password: <code>login pass lvcansetprog X</code>

* If SMS login and password are not set leave two spaces before command: <code>  lvcansetprog X</code>

Line 90: Line 90:

SMS response: <code>LVCAN ProgNum: 11434</code>

−

If during SMS command {{{model|~~FMC1YX~~}}} was in following Sleep mode:

+

If during SMS command {{{model|FMC125}}} was in following Sleep mode:

−

* [[{{{model|~~FMC1YX~~}}}_Sleep_modes#GPS_Sleep_mode|GPS Sleep]] - Program No. will be set immediately.

+

* [[{{{model|FMC125}}}_Sleep_modes#GPS_Sleep_mode|GPS Sleep]] - Program No. will be set immediately.

−

* [[{{{model|~~FMC1YX~~}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep]] - Program No. will be set after device wake up.

+

* [[{{{model|FMC125}}}_Sleep_modes#Deep_Sleep_mode|Deep Sleep]] - Program No. will be set after device wake up.

−

* [[{{{model|~~FMC1YX~~}}}_Sleep_modes#Online_Deep_Sleep_mode|Online Deep Sleep]] - Program No. will be set immediately.

+

* [[{{{model|FMC125}}}_Sleep_modes#Online_Deep_Sleep_mode|Online Deep Sleep]] - Program No. will be set immediately.

−

* [[{{{model|~~FMC1YX~~}}}_Sleep_modes#Ultra_Deep_Sleep_mode|Ultra Deep Sleep]] - Program No. will be set after device wake up.

+

* [[{{{model|FMC125}}}_Sleep_modes#Ultra_Deep_Sleep_mode|Ultra Deep Sleep]] - Program No. will be set after device wake up.

====Entering via Teltonika Configurator====

----

Required conditions:

−

* CAN adapter properly connected to {{{model|~~FMC1YX~~}}} device

+

* CAN adapter properly connected to {{{model|FMC125}}} device

−

CAN adapter program number can be set via '''[[Teltonika Configurator]] → (1) CAN Adapter → (2) Program Number'''. When program number is entered press [[File:Save_to_device.png|25px|link=]] '''(3) Save to device''' button that saves the entered program number into {{{model|~~FMC1YX~~}}}.

+

CAN adapter program number can be set via '''[[Teltonika Configurator]] → (1) CAN Adapter → (2) Program Number'''. When program number is entered press [[File:Save_to_device.png|25px|link=]] '''(3) Save to device''' button that saves the entered program number into {{{model|FMC125}}}.

[[Image:Can adapter conf.png|700px]]

Line 108: Line 108:

----

Required conditions:

−

* CAN adapter properly connected to {{{model|~~FMC1YX~~}}} device

+

* CAN adapter properly connected to {{{model|FMC125}}} device

* Vehicle ignition must be ON

Line 141: Line 141:

|}

−

==={{{model|~~FMC1YX~~}}} CAN Adapter parameters configuration===

+

==={{{model|FMC125}}} CAN Adapter parameters configuration===

----

====Teltonika Configurator====

CAN Adapter configuration can be performed using [[Teltonika Configurator]] via '''Micro-USB cable''' or '''Bluetooth connection''' when CAN Adapter is connected to the vehicle.

−

When {{{model|~~FMC1YX~~}}} is connected to the CAN Adapter, user can see all information that is received from the vehicle in [[Teltonika Configurator]]''' → Status → CAN Adapter''' tab or [[Teltonika Configurator]]''' → CAN Adapter''' section. In '''Status → CAN Adapter''' tab you can see information about CAN adapter and its readable parameters. In '''CAN Adapter''' section you can configure CAN Adapter and see incoming CAN bus data highlighted by '''green''' background color. Incoming data in both sections is automatically refreshed every 5 seconds. CAN bus data which should be readable from your vehicle is provided in "CAN Adapter supported vehicles list", which you can get from Teltonika Sales Representative.

+

When {{{model|FMC125}}} is connected to the CAN Adapter, user can see all information that is received from the vehicle in [[Teltonika Configurator]]''' → Status → CAN Adapter''' tab or [[Teltonika Configurator]]''' → CAN Adapter''' section. In '''Status → CAN Adapter''' tab you can see information about CAN adapter and its readable parameters. In '''CAN Adapter''' section you can configure CAN Adapter and see incoming CAN bus data highlighted by '''green''' background color. Incoming data in both sections is automatically refreshed every 5 seconds. CAN bus data which should be readable from your vehicle is provided in "CAN Adapter supported vehicles list", which you can get from Teltonika Sales Representative.

−

The CAN Adapter I/O element can be configured like any other I/O element in [[Teltonika Configurator]]. All information about I/O element parameters description is in section [[{{{model|~~FMC1YX~~}}} I/O settings|I/O settings]].

+

The CAN Adapter I/O element can be configured like any other I/O element in [[Teltonika Configurator]]. All information about I/O element parameters description is in section [[{{{model|FMC125}}} I/O settings|I/O settings]].

[[Image:Fmb120_can_conf_example.png|800px|none]]

Line 154: Line 154:

=====Send data with 0, if ignition is off=====

----

−

Depending on CAN Adapter I/O parameters and ignition status, {{{model|~~FMC1YX~~}}} can send locked (last known) CAN Adapter I/O and active (real time) parameters values or reset values to 0. When ignition is off, CAN Adapter I/O parameters values sent to server are:

+

Depending on CAN Adapter I/O parameters and ignition status, {{{model|FMC125}}} can send locked (last known) CAN Adapter I/O and active (real time) parameters values or reset values to 0. When ignition is off, CAN Adapter I/O parameters values sent to server are:

{| class="wikitable" style="width:40%;"

Line 323: Line 323:

GPRS commands require [[Codec 12]] protocol.

−

For more SMS commands please see [[{{{model|~~FMC1YX~~}}} SMS/GPRS command list|SMS/GPRS command list]]

+

For more SMS commands please see [[{{{model|FMC125}}} SMS/GPRS command list|SMS/GPRS command list]]

{| class="wikitable" style="width:80%;"

Line 332: Line 332:

|-

| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcansetprog #

−

| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Set program number to CAN Adapter that is connected to {{{model|~~FMC1YX~~}}}. # - three digit number that identity vehicle.

+

| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Set program number to CAN Adapter that is connected to {{{model|FMC125}}}. # - three digit number that identity vehicle.

| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes

|-

Line 340: Line 340:

|-

| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | lvcangetprog

−

| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Get program number from CAN Adapter that is connected to {{{model|~~FMC1YX~~}}}.

+

| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Get program number from CAN Adapter that is connected to {{{model|FMC125}}}.

| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | Yes

|-

Line 398: Line 398:

In order to update your device‘s firmware please follow a quick and simple step-by-step guide which is below. The procedure is the same for all devices.

−

*~~FMC1YX~~ device, which is connected to the CAN adapter (or [[FMB140]] which has internal CAN adapter), must be registered in Fota Web – device‘s model, firmware version, serial number and other information must be shown.

+

*FMC125 device, which is connected to the CAN adapter (or [[FMB140]] which has internal CAN adapter), must be registered in Fota Web – device‘s model, firmware version, serial number and other information must be shown.

−

*A correct firmware version must be uploaded to the ~~FMC1YX~~ device. Currently this feature is only supported with firmware version 03.25.11.Rev144. Once device with correct firmware version connects to Fota Web on the next scheduled connection (or instant connection, initiated by an SMS command "web_connect"), a small, blue, „CAN“ logo will appear next to the device‘s model:

+

*A correct firmware version must be uploaded to the FMC125 device. Currently this feature is only supported with firmware version 03.25.11.Rev144. Once device with correct firmware version connects to Fota Web on the next scheduled connection (or instant connection, initiated by an SMS command "web_connect"), a small, blue, „CAN“ logo will appear next to the device‘s model:

[[Image:111I registered.jpg|1160x1160px|center]]

−

*A current version of the CAN adapter version can be checked by pressing a small „i“ button on the right of fleet management device details. All ~~FMC1YX~~ device‘s and CAN adapter‘s details are listed in one window:

+

*A current version of the CAN adapter version can be checked by pressing a small „i“ button on the right of fleet management device details. All FMC125 device‘s and CAN adapter‘s details are listed in one window:

[[Image:z111FM OldDate.jpg|1162x1162px|center]]

Line 427: Line 427:

===CAN Adapter State Flags===

----

−

CAN Adapters receive data about the states of various systems within the vehicle, and send them as flags to {{{model|~~FMC1YX~~}}}. {{{model|~~FMC1YX~~}}} device stores these flags in hexadecimal format, as one variable. Bellow is a list of kept flags and how to retrieve them. The full list of state flags is stored only by:

+

CAN Adapters receive data about the states of various systems within the vehicle, and send them as flags to {{{model|FMC125}}}. {{{model|FMC125}}} device stores these flags in hexadecimal format, as one variable. Bellow is a list of kept flags and how to retrieve them. The full list of state flags is stored only by:

* [[ALL-CAN300]]

Only '''security state flags''' and '''control state flags''' are stored by:

Adam O

0

edits