Changes

# Connect {{{model|FMB1YX}}} '''positive''' and '''ground''' wires to the vehicle power supply lines.<p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>Do not swap power supply lines.<br />Make sure that voltage does not exceed 30V.</b></td></table></p>

# Connect {{{model|FMB1YX}}} '''positive''' and '''ground''' wires to the vehicle power supply lines.<p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>Do not swap power supply lines.<br />Make sure that voltage does not exceed 30V.</b></td></table></p>

# Switch vehicle '''ignition to ACC''' position. {{{model|FMB1YX}}} '''CAN status LED''' on the side should start '''blinking'''.

# Switch vehicle '''ignition to ACC''' position. {{{model|FMB1YX}}} '''CAN status LED''' on the side should start '''blinking'''.

# Configure {{{model|FMB1YX}}} to read CAN bus data or control vehicle by setting its '''program number''' - [[{{{model|FMB1YX}}}_CAN_adapters#CAN_Adapter_Configuration|CAN Adapter configuration]]

# Configure {{{model|FMB1YX}}} to read CAN bus data or control vehicle by setting its '''program number''' - [[{{{FMB140|{{{model|FMB1YX}}}_CAN_adapters#CAN_Adapter_Configuration}}}|CAN Adapter configuration]]

<br />

<br />

[[File:Alert.png|50px|left|link=]]<b>When {{{model|FMB1YX}}} device turns on sleep mode, CAN chip is turned off till device turns off sleep mode.</b>

[[File:Alert.png|50px|left|link=]]<b>When {{{model|FMB1YX}}} device turns on sleep mode, CAN chip is turned off till device turns off sleep mode.</b>

# Switch vehicle '''ignition to ACC''' position.

# Switch vehicle '''ignition to ACC''' position.

# [[SIMPLE-CAN]] / [[MINI-CAN]] '''LED will shine continously''' so device awaits for '''calibration'''.<div><ul><li style="display: inline-block;">[[File:SIMPLE-CAN_calibration.gif|none|thumb|'''Press the switch shortly''' and wait for the LED to start blinking '''every one second'''.<br /><br /><br />]]</li><li style="display: inline-block;">[[File:SIMPLE-CAN after calibration.gif|none|thumb|Automatic calibration process takes up to 10 seconds depending on the vehicle model. Device is calibrated properly then the LED is blinking '''every 2 seconds'''.]]</li></ul></div><p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.</b></td></table></p><br/>

# [[SIMPLE-CAN]] / [[MINI-CAN]] '''LED will shine continously''' so device awaits for '''calibration'''.<div><ul><li style="display: inline-block;">[[File:SIMPLE-CAN_calibration.gif|none|thumb|'''Press the switch shortly''' and wait for the LED to start blinking '''every one second'''.<br /><br /><br />]]</li><li style="display: inline-block;">[[File:SIMPLE-CAN after calibration.gif|none|thumb|Automatic calibration process takes up to 10 seconds depending on the vehicle model. Device is calibrated properly then the LED is blinking '''every 2 seconds'''.]]</li></ul></div><p><table><td>[[File:Alert.png|50px|left|link=]]</td><td><b>If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.</b></td></table></p><br/>

# Configure {{{model|FMB1YX}}} to read CAN bus data by setting its '''program number''' - [[{{{FMB140|{{{model|FMB1YX}}}_CAN_connection,_SIMPLE-CAN_/_MINI-CAN_connection#FMB140_Configuration}}}|CAN Adapter configuration]]<br />

# Configure {{{model|FMB1YX}}} to read CAN bus data by setting its '''program number''' - [[{{{FMB140|{{{model|FMB1YX}}}_CAN_adapters#CAN_Adapter_Configuration}}}|CAN Adapter configuration]]<br />

=={{{model|FMB1YX}}} Configuration==

=={{{model|FMB1YX}}} Configuration==