Wiki Knowledge Base | Teltonika GPS

Changes

Template:FMB001/FMB010 System settings (view source)

Revision as of 09:16, 11 August 2021

692 bytes removed ,  09:16, 11 August 2021
no edit summary
Line 60: Line 60:  
* '''After Ignition ON''' - charger can be enabled after ignition is turned on, except if battery is fully charged or 10 minute timeout has not passed since device was turned on for faster FIX receiving;
 
* '''After Ignition ON''' - charger can be enabled after ignition is turned on, except if battery is fully charged or 10 minute timeout has not passed since device was turned on for faster FIX receiving;
 
* '''Always''' - enables charging all the time (even if any sleep mode is active).}}}
 
* '''Always''' - enables charging all the time (even if any sleep mode is active).}}}
−
{{{analog_input|===Analog Input Value Range===
  −
------------------
  −
[[Image:Analog_input.gif|right|300px]]
  −
In ''Analog Input Value Range'' settings user can choose an analog input range of 10 V or 30 V.<br></br><br></br>}}}
  −
   
===Data Protocol===
 
===Data Protocol===
 
------------------
 
------------------
 
[[Image:Data_protocol.gif|right|300px]]
 
[[Image:Data_protocol.gif|right|300px]]
 
In ''Data Protocol'' settings user can choose which protocol version ('''[[Codec#Codec 8|Codec 8]]''' or '''[[Codec#Codec 8 Extended|Codec 8 Extended]]''') will use for data sending to the server.<br></br>
 
In ''Data Protocol'' settings user can choose which protocol version ('''[[Codec#Codec 8|Codec 8]]''' or '''[[Codec#Codec 8 Extended|Codec 8 Extended]]''') will use for data sending to the server.<br></br>
−
{{{input_mode|===Input Mode===
  −
------------------
  −
[[Image:Input_mode.gif|right|300px]]
  −
In ''Input Mode'' settings user can choose which configurable input will be use: ''DIN2/AIN1'' or ''[[FMB130_Negative_Input_Usage_Scenario|Ground Sense]]''.<br/>
  −
If Ground Sense is selected, the input will act as an inverse Digital Input, where a low voltage level will output "1" using the Ground Sense I/O element, and a high voltage level will output "0".<br></br><br></br>}}}
      
==Static Navigation Settings==
 
==Static Navigation Settings==
Line 85: Line 75:  
==Ignition Source==
 
==Ignition Source==
 
Ignition source will be used to determine ignition of vehicle. {{{voltage|If voltage is between High Voltage Level and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON. If voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.}}}<br>
 
Ignition source will be used to determine ignition of vehicle. {{{voltage|If voltage is between High Voltage Level and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON. If voltage is higher than High Voltage Level or lower than Low Voltage Level - ignition is OFF.}}}<br>
−
{{{img_ignition|[[Image:Ignition_settings.gif|right|300px]]}}}
+
{{{img_ignition|[[Image:FMB001_Ignition.gif|right|300px]]}}}
 
{{{ignition_source|Possible ignition sources:
 
{{{ignition_source|Possible ignition sources:
 
{{{txt_din1|* '''DIN 1''' (Digital Input 1) - if ''DIN1'' is 1 - ignition is ON; if ''DIN1'' value is 0 - ignition is OFF;}}}
 
{{{txt_din1|* '''DIN 1''' (Digital Input 1) - if ''DIN1'' is 1 - ignition is ON; if ''DIN1'' value is 0 - ignition is OFF;}}}
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/66384"