57
edits
Changes
no edit summary
{|
{|
{{#if:{{{TFT_system_settings|}}}
{{#if:{{{TFT_show|}}}
|
|
|===PDOP filter===
|===PDOP filter===
{|
{|
{{#if:{{{TFT_system_settings|}}}
{{#if:{{{TFT_show|}}}
|
|
|===Input/Output Mode===
|===Input/Output Mode===
{|
{|
{{#if:{{{TFT_system_settings|}}}
{{#if:{{{TFT_show|}}}
|
|
|===Analog Input Value Range===
|===Analog Input Value Range===
{|
{|
{{#if:{{{TFT_DOUT_Overcurrent_protection|}}}
{{#if:{{{TFT_show|}}}
|
|
|===DOUT Overcurrent protection===
|===DOUT Overcurrent protection===
{|
{|
{{#if:{{{TFT_show|}}}
{{#if:{{{TFT_Static_Navigation|}}}
|
|
|==Static Navigation Settings==
|==Static Navigation Settings==
<tr style="vertical-align: top; text-align: left;">
<tr style="vertical-align: top; text-align: left;">
<td style="width:75%">User can choose sleep mode. More about sleep modes can be found {{{ctrSleepModes|[[{{{model|X}}} Sleep modes|here]]}}}. <br>
<td style="width:75%">User can choose sleep mode. More about sleep modes can be found {{{ctrSleepModes|[[{{{model|X}}} Sleep modes|here]]}}}. <br>
{{{PT_movement_source|If any of selected movement sources are active, movement mode will be activated. If all selected sources are inactive STOP mode will be enabled. [[Image: PT Sleep exit Source.png]]}}}
{{{PT_movement_source|If any of selected movement sources are active, movement mode will be activated. If all selected sources are inactive STOP mode will be enabled.}}}
</td>
</td>
<td>[[Image:Sleep_mode_{{{model|X}}}.png|right]]</td>
<td>[[Image:Sleep_mode_{{{model|X}}}.png|right]]</td>
{|
{|
{{#if:{{{TFT_ignition_source|}}}
{{#if:{{{TFT_show|}}}
|
|
==Ignition Source==
|==Ignition Source==
[[Image:Mob_Ignition_source.png|right]]
[[Image:Mob_Ignition_source.png|right]]
User can choose an ignition source from digital input (1, 2 or 3), power voltage, CAN and accelerometer. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status. Example: DIN1 and Accelerometer are selected as Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. User can select movement start and movement stop delay time - those parameters are used when accelerometer is selected as an ignition source. Ignition status is used in power management and the following functionalities: Eco/Green driving, Excessive idling, Over speeding, Towing detection and trip.
User can choose an ignition source from digital input (1, 2 or 3), power voltage, CAN and accelerometer. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status. <br>
''For example'', DIN1 and Accelerometer are selected as Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. <br>
Ignition status is used in power management and the following functionalities: Eco/Green driving, Excessive idling, Over speeding, Towing detection and trip.
<br><br><br>
}}
}}
|}
|}
{|
{|
{{#if:{{{TFT_Accelerometer_delay|}}}
{{#if:{{{TFT_Accelerometer_Delay|}}}
|
|
|==Accelerometer Delay Settings==
|==Accelerometer Delay Settings==
</tr>
</tr>
</table>
</table>
}}
}}
|}
|}
{|
{|
{{#if:{{{TFT_accelerometer_calibration|}}}
{{#if:{{{GH_TMT_section|}}}
|
|==Movement Settings==
[[Image:Accelerometer settings.png|right]]
Here the user can set the movement start/stop delays. <br/>
''For example'', if the '''''Movement Start Delay''''' is set to 1s and '''''Movement Stop Delay''''' to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving. Accelerometer Sensitivity in Sleep parameter defines how much movement device needs to experience to exit sleep mode. The lower the sensitivity - the more movement is required.
*<code>Minimal</code> – approximately 40% higher movement threshold comparing to Normal
*<code>Reduced</code> – approximately 20% higher movement threshold comparing to Normal
*<code>Normal</code> – recommended value for most users
*<code>Increased</code> – approximately 20% lower movement threshold comparing to Normal
*<code>Maximum</code> – approximately 40% lower movement threshold comparing to Normal
Changing Accelerometer Sensitivity in Sleep parameter might result in fake movement record or skipped movement events! Only change that if you experience problems with movement detection!
}}
|}
{|
{{#if:{{{TFT_show|}}}
|
|
|==Accelerometer Auto Calibration==
|==Accelerometer Auto Calibration==
{|
{|
{{#if:{{{TFT_Mounting_Guidelines|}}}
{{#if:{{{TFT_show|}}}
|
|
|=== Mounting Guidelines ===
|=== Mounting Guidelines ===
{|
{|
{{#if:{{{TFT_system_settings|}}}
{{#if:{{{TFT_show|}}}
|
|
|==Timestamp Backup==
|==Timestamp Backup==