Default values changes since FMB firmware version 03.18.16.rev.00
Revision as of 15:38, 7 December 2018 by Tomas.kriauciunas (talk | contribs) (Created page with "We are always improving our solutions according Your feedback. The most important task for us is to make our provided IoT solutions as understandable as possible and improve p...")
We are always improving our solutions according Your feedback. The most important task for us is to make our provided IoT solutions as understandable as possible and improve performance from first usage. We understand how to achieve full potential of our products as fast as possible even for new clients. That’s why we are changing some of default configuration parameters values to make devices more efficient. For more information about changes, see the table below. You will find all changed parameters listed there along with explanation, why they were changed.
Default values changes
| Name | Param ID | Old Value | New Value | Change explanation |
|---|---|---|---|---|
| Sleep Mode Time out, min |
103 |
10 |
1440 |
Sleep time out set to 1440 min to avoid lost data when device wakes up from sleep mode. Which may be caused by GPS signal reacquisition time. As a result after short stops during the day device will not go to sleep. But when vehicle is stationary longer than 24 hours (1440 minutes), device will go to deep sleep, to preserve car battery. |
| Record saving/sending |
107 |
After Position Fix |
After Time Sync |
Record saving and sending is now allowed with no valid GPS fix, most importantly the time must be synchronized. Records with synchronized time, but without GPS fix, will have zero coordinates. |
| Eco score allowed events |
700 |
10 |
100 |
Eco score allowed events value was increased to 100 for more accurate evaluation. |
| NTP resync, h |
901 |
0 |
3 |
Network Time resynchronization was previously disabled. Now it will occur every 3 hours, to improve internal clock reliability. |
| Open link timeout, s |
1000 |
30 |
300 |
Records open link timeout between FMB device and AVL server extended to 300s. This will help to minimize GSM operator charges for link activation. |
| Sort by |
1002 |
Newest |
Oldest |
Records sending sequence changed: Oldest records will be sent first. So the records sequence on server would be chronological. |
| Green Driving Max acceleration |
11004 |
2.2 |
2.5 |
Values adjusted to get more accurate readings and avoid falsely triggering harsh acceleration event in Green driving scenario. |
| Green Driving Max braking |
11005 |
2.5 |
2.7 |
Values adjusted to get more accurate readings and avoid falsely triggering harsh braking event in Green driving scenario. |
| Green Driving Max cornering |
11006 |
2.1 |
3.4 |
Values adjusted to get more accurate readings and avoid falsely triggering harsh cornering event in Green driving scenario. |
| Crash Duration, ms |
11401 |
5 |
20 |
Crash detection duration value altered to avoid generation of fake crash events. |
| Crash Threshold, mG |
11402 |
1500 |
2500 |
Crash detection threshold value altered to avoid fake crash events. |
| Towing detection Event timeout, s |
11603 |
0 |
10 |
Towing detection timeout set to 10 seconds to avoid fake towing events while entering the car. If Ignition is not turned on during this time, Towing event may be generated, because of vehicle vibrations caused by door opening and closing. |
| Movement start delay, s |
19001 |
1 |
5 |
Movement start delay time extended to 5 seconds to eliminate fake events when vehicle is stationary. |
| Movement I/O element Averaging constant |
50015 |
1 |
10 |
Movement I/O element state change is now registered only after 1 second (10 avg = 1 sec). Change is made in order to eliminate fake events. |
| Data mode I/O element Priority |
50020 |
Low |
None |
Data mode I/O element is now disabled by default. |
| Speed I/O element Priority |
50090 |
Low |
None |
Speed I/O element is now disabled by default. Speed element is always received along with GNSS information. |
| Active GSM operator I/O element |
50140 |
None |
Low |
Operator code I/O element is now enabled by default and set to low priority. |
| Total odometer I/O element |
50160 |
None |
Low |
Total odometer I/O element is now enabled by default and set to low priority. |
| Battery level % I/O element Event only parameter |
50694 |
Yes |
No |
In case enabled, Battery level % I/O element value will be appended to every record, not just eventual records. |
| Blue-tooth status I/O element |
50720 |
Low |
None |
Blue-tooth status I/O element is now disabled by default. |
| Blue-tooth status I/O element Event only parameter |
50724 |
Yes |
No |
In case enabled, Blue-tooth status I/O element value will be appended to every record, not just eventual records. |