Advanced Pulse Counter

Functionality description

This functionality was added in 03.28.04.Rev.00 firmware version.

When 2kHz pulse counter is enabled, all other scenarios will ignore corresponding DIN state, except DIN1 which can be used to wakeup device from Deep Sleep.

Parameter values

System parameters (ID = 145).  Device/Available/Input port/Frequency:

Device		Not available	DIN1		DIN2		DIN4
			50Hz	2kHz	50Hz	2kHz	50Hz	2kHz
FM3001, FM3010		+
FM4001		+
FMB0	[1-6] - FMB010, FMB001, FMB001 buzzer, FMB003, FMB002, FMB020		+
FMC0	[1, 3-4] – FMC001, FMC003. FMC00A	+
FMM0	[1, 21-22, 34, 41] – FMM001 BG96, FMM001/3 BG95M3, FMM003 BG95M6, FMM00A BG95M1	+
FMB1	[3-4, 23-24] – FMB125 DualSIM, FMB125 no BAT dualSIM, FMB125, FMB125 no BAT		+
	[1-2, 5-6, 21-22]1		+			+
FMC1	FMC120, FMC122, FMC125, FMC130		+
	FMC120, FMC122, FMC130					+
FMU1	[1-5] - FMU120, FMU122, FMU125, FMU130, FMU126, [23, 24]		+
	FMU120, FMU122, FMU130, [24]					+
FMM1	[3, 23] – FMM125 BG96, FMM125 BG95M3		+
	[4, 24-25] – FMM130 BG96, FMM130 BG95M3, FMM13A					+
FMB2	[130, 161] – FMB225, FMB225 DualSIM		+
	[1-3, 132-133] – FMB202, FMB204, FMB206, FMB230, FMB240		+			+
	FMB208, [11-14]							+
FMC2	[130] – FMC225		+
	[131] – FMC130					+
FMM2	[151] – FMM230 BG95M3					+
FMB9	[1-2(21-22)] – FMB900, FMB920 [3-5] - FMB962, FMB964 FMB964 DualSim, [8-11] - FMB965, FMB965 I/O, FMB930, FMB939,			+
	[7] - FMB910		+
FMC9	[1] – FMC920			+
FMM9	[1] – FMM920			+
MCX2	MCX201		+			+
MTB1	MTB100 Storageless, MTB100, [3]		+

1 – [1-2, 5-6, 21-22] - FMB110 DualSIM, FMB120, FMB122 DualSIM, FMB130, FMB140m FMB110 BLE, FMB120, FMB122 BLE

System parameters description

If this function is active, then all other settings associated with the this input are disabled.

Frequency measurement can be performed in 2 different ways:

1. Frequency is measured by counting pulses over time period (997 ms). Method is used for frequencies higher than 100 Hz.
2. Frequency is measured by measuring time between pulses. Method is used for frequencies lower than 100 Hz.

Advanced pulse counter parameter in configurator