Difference between revisions of "ECAN01"

From Wiki Knowledge Base | Teltonika GPS
Line 105: Line 105:
 
==Set up ECAN01==
 
==Set up ECAN01==
  
# Gently remove {{{model|FMB1YX}}} '''cover''' using '''plastic pry tool''' from both sides.<p><b>Note:</b> To properly open a new case please watch this [https://youtu.be/PBXVNXfRjg0 video].</p>
+
# Gently open ECAN01 cover using plastic pry tool from both sides
# Insert '''{{{sim_type|Micro-}}}SIM''' card as shown with '''PIN request disabled''' or read '''[[{{{model|FMB1YX}}} Security info|Security info]]''' how to enter it later in [[Teltonika Configurator]]. Make sure that {{{sim_type|Micro-}}}SIM card '''cut-off corner''' is pointing forward to slot. {{{dual_sim|'''SIM slot 1''' is closer to PCB, '''SIM slot 2''' is the upper one.}}}
+
# Insert CAN wires as shown in figure 5. Please make sure that correct slots are used (CAN High/CAN Low)
{{{be_battery|# Connect '''battery''' as shown to device. Position the battery in place where it does not obstruct other components.
+
# Gently close the device.
# After '''configuration''', see “'''[[{{{model|FMB1YX}}}_First_Start#PC Connection (Windows)|PC Connection (Windows)]]'''”, attach device '''cover''' back.}}}
+
# Device is ready-to-use.
  
 
[[Image:{{{sim_insert_pic1|Fmb120_cover_1.png}}}|260px]][[Image:{{{sim_insert_pic2|Fmb120_cover_2.png}}}|260px]][[Image:{{{sim_insert_pic3|Fmb120_cover_3.png}}}|260px]][[Image:{{{sim_insert_pic4|Fmb120_cover_4.png}}}|260px]]
 
[[Image:{{{sim_insert_pic1|Fmb120_cover_1.png}}}|260px]][[Image:{{{sim_insert_pic2|Fmb120_cover_2.png}}}|260px]][[Image:{{{sim_insert_pic3|Fmb120_cover_3.png}}}|260px]][[Image:{{{sim_insert_pic4|Fmb120_cover_4.png}}}|260px]]

Revision as of 09:57, 22 January 2020

Main Page > CAN Trackers & Adapters > ECAN01
ECAN01 TOP.png
ECAN01 BOTTOM.png

ECAN01 (Easy-CAN) is contactless adapter used to read vehicle CAN Bus data. ECAN01 (Easy-CAN) adapter should be used in combination with:

It reads can bus data through the isolation of wires without damaging them and forwards signals to tracking device.

Features

  • Easy-CAN collects vehicle data from CAN bus without damaging the wires
  • Powered from on-board power source
  • Reads the signals through the isolation of CAN bus wires
  • Easy to install and operate

Technical features

PARAMETER VALUE
Minimum Typical Maximum Unit
Supply Voltage
Supply Voltage (Recommended Operating Conditions) +10 +12 +30 V
Current Consumption
Working Mode 6.9 mA
Sleep Mode 1.2 mA
Operating Temperature
Operating Temperature -25 +85 °C
Protection
Internal resettable fuse (max 33 V) 750 mA
  • Dimensions 39.8 x 18 x 16.7 mm
  • CAN-BUS speeds up to 1000 kb/s

Pinout

PIN NUMBER PIN NAME

DESCRIPTION

1 CAN L (Blue) Connect to CAN L input of CAN BUS converter
2 CAN H (White/Blue) Connect to CAN H input of CAN BUS converter
3 VCC (RED) Power supply (10-30) V DC (+)
4 GND (-) (Black) Ground wire (10-30) V DC (-)
ECAN01 pinout.png

Wiring scheme

ECAN01 wiring scheme.png

Set up ECAN01

  1. Gently open ECAN01 cover using plastic pry tool from both sides
  2. Insert CAN wires as shown in figure 5. Please make sure that correct slots are used (CAN High/CAN Low)
  3. Gently close the device.
  4. Device is ready-to-use.

Fmb120 cover 1.pngFmb120 cover 2.pngFmb120 cover 3.pngFmb120 cover 4.png

ECAN01 Certification & Approvals

Nomenclature, classification codes

FAQ


YouTube

Teltonika CAN adapters Part 1: Introduction
Teltonika CAN adapters Part 2: Installation

External Links

ECAN01 Teltonika