EYE FUNCTIONALITIES

From Wiki Knowledge Base | Teltonika GPS

Page Description

This page will describe EYE device functionalities, their value flow and required firmware and software versions,

EYE APP 1.2.2-89

Search device with QR scan

Functionality: Now you can find devices with QR scan by pressing scan button EYE APP QR BUTTON.png and scanning device QR code.

Firmware: 1.2.1.R.0+

Value: Easier device management

Flow: 1. Tap EYE APP QR BUTTON.png 2. scan the QR code engraved onto EYE device

EYE APP QR PRESS BUTTON.pngEYE APP QR SCAN.pngEYE APP QR SCAN EXAMPLE.png

Customized Sensor Selection

Functionality: Users can disable sensors reading leaving only the sensors they require.

Firmware: 1.2.10.R.4+

Value: Data saving, battery life can be expanded by disabling accelerometer.

Flow: 1. Connect to EYE device 2. Click "configure" 3. Expand Active sensors tab 4. Uncheck sensors you want to deactivate 4. Save your configuration.

EYE APP CHOOSE ONE SENSORS.pngEYE APP ONE SENSOR VIEW.pngEYE APP CHOOSE FOUR SENSORS.pngEYE APP FOUR SENSOR VIEW.png

Auto-Disconnect Timer

Functionality: After 2 minutes of inactivity, users will be automatically disconnected from the device. Before disconnection, you will have the option to maintain the connection.

Firmware: 1.2.10.R.4+

Value: Enhanced user privacy and energy saving.

Flow: 1. Connect to EYE device 2. Do not perform any saving actions for 2 minutes.

EYE APP TWO MINUTE WAIT.pngEYE APP DISCONNECTED AFTER TWO MINUTES.pngEYE APP DISCONNECTED WHILE CONFIGURING.png

Visible battery voltage

Functionality: Eye App now provides a clear and convenient readout of the battery's voltage level, keeping users informed about their device's power status.

Firmware: 1.2.1.R.0+

Value: Keeping users informed about their device's power status.

Flow: 1. Expand sensor card in the overview screen or connect to the device

EYE APP VISIBLE BATTERY VOLTAGE.png

12 characters name

Functionality: Users can now assign names of up to 12 characters,

Firmware: 1.2.1.R.0+

Value: A full MAC address can be used as the name.

Flow: 1. Connect to EYE device 2. Click "configure" 3. Expand Name settings drop down 4. Enter desired name 4. Save your configuration.
EYE APP 12 CHAR NAME.png

EYE APP 1.2.0-63

PIN code

Functionality: Eye App will time-out users on for 5 minutes after 5 unsuccessful PIN attempts

Firmware: 1.2.1.R.0 to 1.2.8.R.2

Value: Keeping users informed about their device's power status.

Flow: 1. Tap the selected device to connect to it 2. Enter PIN incorrectly, fail to enter PIN correctly 4 more times 3. wait for 5 min timeout a

Screenshot 20230503 165303 EYE APP edited.jpgScreenshot 20230509 1518232 EYE APP.jpgScreenshot 20230509 152802 EYE APP.jpg



SW version requirements EYE APP: 1.2.0-60+

Firmware: 1.2.9.R.8+

Short step desc. Tap the selected device to connect to it Enter PIN incorrectly Fail to enter PIN correctly 4 more times Wait for 5 min timeout and enter PIN incorrectly Fail to enter PIN correctly 4 more times
Additional desc. Device is locked for 5 min but will allow to connect with PIN again after timeout Device is locked with PUK code now and will remain so until correct PUK is entered, see PUK code unlock.
Failed attempt at functionality visual
Screenshot 20230503 165303 EYE APP edited.jpg
Screenshot 20230509 1518232 EYE APP.jpg
Screenshot 20230509 152802 EYE APP.jpg
Screenshot 20230509 151823 EYE APP.jpg
Screenshot 20230509 175501 EYE APP PinnAttemptAfter5min.jpg
PUK code unlock
SW version requirements EYE APP: 1.2.0-60+

Firmware: 1.2.9.R.8+

Step No.
Short step desc. Tap the blocked device to connect to it Enter PUK Connected
Additional desc. PIN automatically resets to default
Successful attempt at functionality visual
Screenshot 20230503 165303 EYE APP edited.jpg
PUK insert.jpg
Step desc. Tap the selected device to connect to it Enter PUK incorrectly Fail to enter PIN correctly 4 more times
Additional desc. PUK is rejected and you can only go back or enter correct PUK
Failed attempt at functionality visual
Screenshot 20230503 165303 EYE APP edited.jpg
Screenshot 20230512 163210 Gallery.jpg


Hibernate mode:

Wake up:
SW version requirements Firmware: 1.2.9.R.8+
Step No. 1-3 4
Short step desc. Attach magnet to sleeping device and wait for LED to blink. Device starts broacasting
Additional desc. Now device is discoverabled, scannable, connectable via BLE.
Successful attempt at functionality visual
Send to sleep:
SW version requirements EYE APP: 1.2.0-60+

Firmware: 1.2.9.R.8+

Step No. 1 2 3
Short step desc. While connected and in overview tap "Send device to sleep" Confirm your selection Wait for EYE App to disconnect
Additional desc. Device is no longer connectable or findable until wake up step is performed.
Successful attempt at functionality visual
Device screen 1.2.8 2.jpg
Screenshot 20230509 173323 EYE APP.jpg
Screenshot 20230512 164509 Gallery.jpg