| Line 1: |
Line 1: |
| − | ==Introduction==
| + | {{Template:FMx6 and Tachograph Solution|model=FMB640}} |
| − | Teltonika [https://ddd.teltonika.lt WEB Tacho] is an online service that allows to remotely downloading Tachograph files from supported tachographs.
| |
| − | The solution is a big forward leap in remote tachograph data files download, manageable and does not require any complex software* installation.
| |
| − | Everything is accessible via the web page. Now you can download tachograph files from any place and from any PC via internet access. FMB640 device has a possibility to connect to Web Tacho IP every 1 hour and check if there are any schedules for downloading DDD files. If FMB640 connects to the Web tacho server, and there is a planned schedule but another device is already downloading and the company card is in use, the device
| |
| − | keeps a link with the Web Tacho server but still sends data to the main server with AVL data. After
| |
| − | successful download, the device closes link with Web Tacho and reconnects after 1 hour. Data is
| |
| − | stored on a secure server and can be accessed only by your authorized users. <br>
| |
| − | You don't need to worry that any file is lost and you have to download it from tachograph once again.
| |
| − | | |
| − | ''*- requires company card reader software installation on a single company PC''
| |
| − | | |
| − | ==Supported tachographs and formats==
| |
| − | The solution supports not only the standard DDD file extension but also Spanish TGD and French V1B, C1B file formats. You simply set required one in Web Tacho user settings.<br />
| |
| − | | |
| − | '''NOTE:''' To check whether VDO tachograph is supported or not, Teltonika [https://tacholookup.teltonika.lt/ Tachograph Lookup] can be used.
| |
| − | | |
| − | Supported devices are: <br />
| |
| − | | |
| − | *[[#See also|Intellic Siemens VDO Digital Tachograph]]
| |
| − | *[[#See also|Intellic Stoneridge Tachograph]]
| |
| − | *[[#See also|Intellic EFAS version 4]]
| |
| − | | |
| − | ===Siemens VDO Digital Tachograph===
| |
| − | | |
| − | Siemens VDO Digital Tachograph – DTCO 1381 (release 1.3a, 1.4 or later):
| |
| − | the version can be checked on tachograph or in printout (Technical data: printout -> vehicle -> techn. data) as shown in pictures below:<br />
| |
| − | | |
| − | [[Image:VDO Tachograph 1.png|525px|center]]
| |
| − | | |
| − | Tachograph Part number - <span style="color:#007FFF">1381.1234567890</span> is indicated in blue color - you can use TachoLookup([https://tacholookup.teltonika.lt/ Tachograph Lookup]) to doublecheck if tachograph is supported.
| |
| − | Software version <span style="color:#007FFF">V1420</span> indicates that tachograph is version (release) 1.4
| |
| − | Same information can be found behind the print cabinet label and on the label on the back of the tachograph:<br />
| |
| − | | |
| − | [[Image:VDO Tachograph 2.png|550px|center]]
| |
| − | | |
| − | ===Stoneridge Tachograph===
| |
| − | | |
| − | Stoneridge Tachograph – SE5000 (release 7.1 or later). The version can be checked on tachograph or in printout (Daily Driver printout on the left: PRINT -> 24h card/ Technical data on the right: PRINT -> technical data) as shown in pictures below:<br />
| |
| − | | |
| − | [[Image:STONERIDGE_1.3.png|750px|center]]
| |
| − | | |
| − | Tachograph part number is indicated in blue <span style="color:#007FFF">900588RA/37R01</span> "RA" indicates that this is 8th revision. Other revisions can be checked by looking at number after "R", for example R7.1 - Revision 7.1. You can use TachoLookup(linkas) to doublecheck if tachograph is supported.
| |
| − | | |
| − | ===Intellic EFAS version 4===
| |
| − | | |
| − | Intellic EFAS 4 - we support EFAS-4 tachographs from version 4.5. Supported tachographs can be identified by first 6 digits of “EU-serial code” and should start with: E4T010, E4T012, E5T018, E5T020 as shown in printout (Technical data: Printout ->Technical data) example bellow:<br />
| |
| − | | |
| − | [[Image:INTELLIC 1.png|600px|center]]
| |
| − | | |
| − | Required numbers are indicated in blue color <span style="color:#007FFF">E4T010 e1222 010.0000123456</span> this is a combination of Device part number and serial code. You can use Tachograph lookup ([https://tacholookup.teltonika.lt/ Tachograph Lookup]) to check if tachograph is supported - enter the combination without e1-222 part and dots: E4T0100100000123456
| |
| − | This information can be found on tachograph label as well:<br />
| |
| − | | |
| − | [[Image:INTELLIC 2.png|600px|center]]
| |
| − | | |
| − | ==Remote Data Download (RDD) via FMS==
| |
| − | | |
| − | When RDD (Remote Data Download) signal available on '''FMS'''.
| |
| − | | |
| − | Applies to:
| |
| − | * DAF CF - LF - XF
| |
| − | * IVECO Stralis I / II/ Hi-Way
| |
| − | * Renault D / Magnum DXI & E-TECH / Midlum DXI / Premium DXI / Renault T-K-C
| |
| − | * Volvo FH - FM - FL
| |
| − | | |
| − | If the '''RDD''' signal is available on the '''FMS''' interface, no additional connection is required. In this case, the '''CANx LOW and HIGH''' wires from the FMx640 are connected to '''PIN 6 and 9''' on the '''FMS''' connector.
| |
| − | Additionally, '''PIN 10''' can be used for ignition detection using '''DIN1''' wire.
| |
| − | | |
| − | [[image:FMS_connector.png|central]]
| |
| − | [[image:FMS_connector1.png|central]]
| |
| − | | |
| − | More information about FMS CABLE can be found on [https://teltonika-gps.com/product/fms-cable/ Teltonika Page] <br><br><br>
| |
| − | | |
| − | For the following vehicles regarding the '''RDD''', please contact the manufacturer:
| |
| − | * MAN TGX - TGA - TGL - TGM
| |
| − | * Mercedes Actros / Antos / Atego / Arocs / Axor II
| |
| − | * Scania R - P - G - S
| |
| − | | |
| − | If the '''RDD''' signal is '''NOT''' available on the '''FMS''' interface, you need to retrieve the '''RDD''' data by connecting to the tachograph's C connector using provided instructions below.
| |
| − | | |
| − | ==Connecting to tachograph==
| |
| − | [[Image:Tacho_connection.PNG|800px|center]]
| |
| − | <br />
| |
| − | | |
| − | Before connecting tachograph wires, it is required to measure CAN line resistance
| |
| − | while tachograph is switched off:<br />
| |
| − | | |
| − | #Turn off the vehicle ignition;<br />
| |
| − | #Measure resistance between the C5 (CAN2 H) and C7 (CAN2 L) contacts;<br />
| |
| − | #If the multimeter shows ~120 Ohms, skip the next step;<br />
| |
| − | #If the multimeter shows kilo Ohms resistance then it is needed to connect tachograph C8 (CAN-RES) and C7 (CAN2 L) contacts with wire and then perform further actions;<br />
| |
| − | #Re-measure the resistance of the line – it has to be ~120 Ohms.<br />
| |
| − | #Connect CAN2 L and CAN2 H wires to tachograph (C5 (CAN2 H) and C7 (CAN2 L))<br />
| |
| − | | |
| − | | |
| − | *All of the same level CAN-L and CAN-H wires must be interlaced with each other.<br />
| |
| − | | |
| − | [[Image:Wires.PNG|800px|center]]
| |
| − | | |
| − | *CAN wire need to be installed as far as possible from GSM antenna.<br />
| |
| − | | |
| − | Below is a wiring diagram of Tachograph and FM6400/FMB640 device:<br />
| |
| − | | |
| − | [[Image:Wiring_diagram.PNG|800px|center]]
| |
| − | | |
| − | | |
| − | ==Checking connection (Tachocheck SMS)==
| |
| − | After successful connection ''tachocheck'' SMS message can be sent to the device for checking if
| |
| − | data presented on connected lines, by other words if connections were done correctly. It is
| |
| − | used for getting status information. SMS response is of such structure:
| |
| − | CAN_2:[TRC],[ABCD], K-Line:[K]<br />
| |
| − | | |
| − | | |
| − | [T] – Tachograph presence on the bus:
| |
| − | *0 – Tachograph doesn’t respond on the bus;
| |
| − | *1 – Tachograph responds on bus.<br />
| |
| − | | |
| − | | |
| − | [R] – Response to Open Remote Session validity check:
| |
| − | *0 – Wrong or unknown response (failed to open Remote Session);
| |
| − | *1 – Tachograph responds positively (Remote Session opened successfully).<br />
| |
| − | | |
| − | | |
| − | [C] – Response to Close Last Authentication Session validity check:
| |
| − | *0 – Wrong or unknown response (failed to close last authentication session);
| |
| − | *1 – Last authentication session closed successfully, the device is ready to open new authentication session.<br />
| |
| − | | |
| − | | |
| − | [K] – K-Line data presence on the bus:
| |
| − | *0 – K-Line data not present on the bus;
| |
| − | *1 – K-Line data present on bus.<br />
| |
| − | | |
| − | | |
| − | [ABCD] – FMS data presence on the bus:
| |
| − | *0000 – FMS data not present on the bus;
| |
| − | *Non-zero – FMS data detected on bus.<br />
| |
| − | | |
| − | | |
| − | '''SMS answer which shows correct line connections looks like “CAN_2:[111],[ABCD], K-Line:[K]”.'''
| |
| − | '''Such SMS answer means DDD files can be downloaded from tachograph.'''
| |
| − | | |
| − | ==Configuring device==
| |
| − | '''In FMB640 configurator “CAN/Tachograph” section tachograph settings should be set in order to download files.<br />'''
| |
| − | <br />
| |
| − | | |
| − | '''Tachograph settings:''' <br />
| |
| − | '''DDD download source''' – to which CAN line tachograph is connected;<br />
| |
| − | '''Tachograph ignition source''' – which DIN is connected to vehicle ignition ("Ignition" parameter - tachograph ignition source will be the same as configured in "System" -> "Ignition Source");<br />
| |
| − | | |
| − | | |
| − | '''WEB Tacho Settings:'''<br />
| |
| − | '''Status''' - functionality enabling;<br />
| |
| − | '''Domain''' – server domain where files will be send;<br />
| |
| − | '''Port''' – server port where files will be send;<br />
| |
| − | '''Start delay''' – delay after turning on ignition to start procedure of file sending.<br />
| |
| − | | |
| − | [[Image:Configuration_tacho1111.PNG|800px|center]]
| |
| − | | |
| − | ==External links==
| |
| − | https://teltonika-gps.com/product/tachograph-web/ <br />
| |
| − | https://teltonika-gps.com/product/FMB640/ <br />
| |
| − | https://wiki.teltonika-gps.com/view/FMB640
| |
| − | | |
| − | [[Category:WEB Tacho]]
| |
