4,628
edits
Changes
mLine 4:
Line 4: − + Line 14:
Line 14: − + Line 20:
Line 20: − + Line 45:
Line 45: + + Line 77:
Line 79: − + Line 85:
Line 87: − + Line 99:
Line 101: − + Line 109:
Line 111: − + − + Line 123:
Line 125: − +
Text replacement - "Bluetooth(?!®)" to "Bluetooth®"
'''Description:'''
'''Description:'''
Netronix NBL-2 - wireless Bluetooth RFID reader with additional buttons.
Netronix NBL-2 - wireless Bluetooth® RFID reader with additional buttons.
'''NBL-2 is great in these use cases:'''
'''NBL-2 is great in these use cases:'''
* Mifare® Classic, Desfire card supports
* Mifare® Classic, Desfire card supports
* Bluetooth low energy module
* Bluetooth® low energy module
* Operating frequency - 13,56MHz
* Operating frequency - 13,56MHz
* Built in two LED indicators
* Built in two LED indicators
* UID and card DATA available
* UID and card DATA available
* Configure via BL link
* Configure via BL link
* Firmware update via Bluetooth
* Firmware update via Bluetooth®
==Product Specification==
==Product Specification==
{| class="wikitable"
{| class="wikitable"
==NBL-2 Configuration==
==NBL-2 Configuration==
'''For the NBL Tools application, contact the Netronix NBL manufacturer.'''
First, you have to make sure that NBL-2 firmware version is updated to 1.3.
First, you have to make sure that NBL-2 firmware version is updated to 1.3.
5. Wake up the device - for example, by applying a card to it.
5. Wake up the device - for example, by applying a card to it.
6. Select the device from the list (long press), then select Update firmware from the drop-down menu and press the Start button.
6. Select the device from the list, then select Update firmware from the drop-down menu and press the Start button.
[[File:NBL conf9.jpg.jpg|frameless|520x520px]] [[File:NBL conf8.jpg.jpg|frameless|519x519px]]
[[File:NBL conf9.jpg.jpg|frameless|520x520px]] [[File:NBL conf8.jpg.jpg|frameless|519x519px]]
'''2. Power OFF /Reset to default settings'''
'''2. Power OFF /Reset to default settings'''
To set factory defaults and un-pairingboth buttons must be pressed for 5 seconds additionally button 1 (blue) must be pressed first. It is also factory/transport configuration.
To set factory defaults and unpairing both buttons must be pressed for 5 seconds additionally button 1 (blue) must be pressed first. It is also factory/transport configuration.
Procedure:
Procedure:
# Press Button 2 and hold
# Press Button 2 and hold
# Keep the button pressed for 5 seconds
# Keep the button pressed for 5 seconds
# The PowerOnwillbe signaledby flashing LED1 and LED2
# The Power On will be signaled by flashing LED1 and LED2
==Device configuration==
==Device configuration==
This functionality is available from firmware version FMB.Ver.03.28.05
This functionality is available from firmware version FMB.Ver.03.28.05.Rev.04
Setting up NBL-2 device to connect with FMB device.
Setting up NBL-2 device to connect with FMB device.
Go to Teltonika configurator -> Bluetooth 4.0 and set it up like it shown in this screenshot (MAC address will depend on your particular NBL sensor):
Go to Teltonika configurator -> Bluetooth® 4.0 and set it up like it shown in this screenshot (MAC address will depend on your particular NBL sensor):
[[File:Nbl2 1.png|frameless|660x660px]]
[[File:Nbl2 1.png|frameless|660x660px]]
Then go to I/O settings:
Then go to I/O settings:
Make sure to enable the BLE RFID #1 parameter (ID: 51740). We would recommend to set the operand to „On Change“.
Make sure to enable the BLE RFID #1 parameter (ID: 51740). We would recommend to set the operand to „[[Template:FMB I/O settings#Operand On Change|On Change]]“.
[[File:Nbl2 3.png|frameless|999x999px]]
[[File:Nbl2 3.png|frameless|999x999px]]