TMT250 Stable firmware

Main Page > Autonomous Trackers > TMT250 > TMT250 Firmware and configurator > TMT250 Stable firmware
STABLE BASE FIRMWARE
FIRMWARE VERSION: 55.02.03.Rev.05
CONFIGURATOR VERSION: 1.7.66_B.55.2_R.10
RELEASE DATE:
2023-12-13
DOWNLOAD
Firmware
Configurator
DOWNLOAD ALL
DOWNLOAD ALL

CHANGELOG

VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.02.03.Rev.05
1.7.66 B.55.2 R.10
2024-01-30
  • [CHN] Added new AVL ID's SMS events tab
  • [FIX] Fixed Online vs Offline configuration discrepancies
  • [FIX] Fixed Ultra Deep Sleep naming mismatch
  • [FIX] Fixed Tool Tips inaccuracies
  • [ADD] Added EYE Sensors support settings and filtering by sensors name and MAC address
  • [CHN] Changed device wiki links to teltonika-gps
  • [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab
  • [FIX] Fixed Roaming operator/Operator Black List .csv file importing
  • [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
  • [ADD] Added configurable accelerometer sensitivity settings
  • [ADD] Added continuous battery charging mode
  • [CHN] Changed minimum BLE scan start period value
  • [CHN] Added possibility to send SMS AVL ID event to few numbers
  • [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
  • [ADD] Added CSQ level parameter
  • [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
  • [FIX] Added configurable accelerometer sensitivity options in sleep mode
  • [FIX] Fixed ‚btgetlist 3‘ SMS command
  • [FIX] Changed battery voltage measurement and charging algorithm
  • [ADD] Added EYE Sensor support
  • [ADD] BLE Sensors Custom field data are displayed in decimal now
  • [FIX] Fixed batteries percentage calculation when voltage is Fully charged
  • [FIX] Refactored battery percentage limits checking algorithm
  • [FIX] Fixed battery charging status
  • [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
  • [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
  • [FIX] Fixed GSM established LED indication turning off issue
  • [CHN] Changed minimum BLE scan start period configuration value.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.02.03.Rev 05
1.7.66_B.55.2_R.10
2023-12-13
  • [CHN] Added new AVL IDs SMS events tab
  • [FIX] Fixed Online vs Offline configuration discrepancies
  • [FIX] Fixed Ultra Deep Sleep naming mismatch
  • [FIX] Fixed Tool Tips inaccuracies
  • [ADD] Added EYE sensors support settings and filtering by sensor's'name and MAC address
  • [CHN] Changed device wiki links to teltonika-gps
  • [CHN] Moved EYE Sensor I/O settings to Bluetooth 4.0 tab.
  • [FIX] Fixed Roaming operator/Operator Black list .csv file importing
  • [FIX] Fixed Maximum GPS Satellites Quantity parameter (ID: 906) value
  • [ADD] Added configurable accelerometer sensitivity settings
  • [ADD] Added continuous battery charging mode
  • [CHN] Changed minimum BLE scan start period value.
  • [CHN] Added possibility to send SMS AVL ID event to few numbers
  • [FIX] Fixed sensors scanning issue, then Beacon Detection is Disabled or set to beacons No Send mode.
  • [ADD] Added CSQ level parameter
  • [ADD] Added ‚ shutdown‘ SMS/GPRS command to power off device
  • [ADD] Added configurable accelerometer sensitivity options in sleep mode
  • [FIX] Fixed ‚btgetlist 3‘ SMS command
  • [FIX] Changed battery voltage measurement and charging algorithm
  • [ADD] Added EYE sensor support
  • [ADD] BLE sensors Custom field data are displayed in decimal now
  • [FIX] Fixed batteries percentage calculation when voltage is Fully charged
  • [FIX] Refactored battery percentage limits checking algorithm
  • [FIX] Fixed battery charging status
  • [FIX] Fixed BT records generation issue, when BLE devices feature is disabled
  • [FIX] Fixed beacon buffer cleanup after the end of BLE scanning or periodic beacon record creation.
  • [FIX] Fixed GSM established LED indication turning off issue
  • [CHN] Changed minimum BLE scan start period configuration value.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES
55.01.02.Rev.01
1.6.11_R.30
2021.10.25
  • Change No Movement/Movement event SMS text
  • Added Race Mode feature
  • Added Race Mode for GNSS data live tracking
  • Fixed LED indication stuck when Man-Down Cancel button is pressed
  • Fixed FW version display in FOTA WEB
  • Fixed possibility to configure forbidden GNSS source via SMS or GPRS
  • Fixed fake movement events when Low power mode is used
  • Fixed BLE scan stuck when Xiaomi bracelet is used
  • Fixed restarts when Beacon on Demand feature is used for longer time
  • Fixed Alarm call delay issue
  • Fixed FW update issue with XT26G01CWSIGT flash
  • Added XT26G01CWSIGT and GD5F1GQ5UE NAND flash support
  • Changed minimum charging temperature from -10°C to 1°C
  • SMS commands will return time with applied time zone
  • The maximum battery charging temperature changed from 50°C to 45°C
  • Maximum operating temperature changed from 65°C to 59°C
55.00.21.Rev.00
1.6.11_R.26
2021.08.10
  • 'Data Acquisition' tool tips and labels changed.
  • Changed BLE 'Update frequency' name and tool tips.
  • Fixed 'Beacon on demand' labels.
  • Added possibility to Enable or Disable Mandown/Movement/No Movement features while charging.
  • Accelerometer and movement detection improvements.
  • Fixed invalid SMS number when reporting position after call.
55.00.18.Rev.02
1.6.11_R.23
2021.05.13
  • No changes
  • Fixed issue which occurred during manufactory testing phase with Ver.55.00.18.Rev.01 where device could end with GNSS State = 0
55.00.18.Rev.01
1.6.11_R.23
2021.05.07
  • Increased Beacon List from 25 to 100
  • Added On Demand Tracking On/Off/Switch button action
  • Added On Demand Tracking event indication settings
  • Increased Configured beacons count from 25 to 100
  • If Beacon record sending is configured to be 'Eventual', send only if device sees any beacons
  • Improved Power On/Off feature notifications
  • Power save mode is working with Data Acquisition time 60s and above
  • On Demand Tracking functionality improved with button control and On Demand Tracking event indication
55.00.10.Rev.01
1.6.11_R.16
2020.11.13
  • Added Last Known Position feature settings
  • Added Power On/Off event settings
  • Added Power off with Power key settings
  • Added Custom BLE I/O parameters
  • Added Last Known Position feature on HIGH priority event (alarm, amber alert, man-down, etc).
  • When device gains current GPS position after HIGH priority event was generated, device sends another HIGH priority event with updated position and GPS fix timestamp.
  • Reworked GNSS status SMS template.
  • Fixed issue of data acquisition parameters reset to default values.
55.00.07.Rev.09
1.5.15_C.002
2020.10.20
  • Minor changes
  • Important change of charging algorithm. This algorithm provides higher safety and prolonging battery’s life longevity.
  • Corrected battery display in percentage
  • Improved charging current from PC.
55.00.07.Rev.07
1.5.15_C.002
2020.09.16
  • Minor changes
  • Lowered battery charging current from wall charger to 425mA.
  • Fixed battery LED indication when battery is fully charged.
55.00.07.Rev.02
1.5.15_C.002
2020.03.17
  • Added Man-Down Event On Exit and On Entrance parameters
  • Updated Server IP and Port saving procedures.
  • Reworked Generate Event On Exit and On Entrance logic.
  • Reworked handheld devices switching between Charging and Normal modes.
  • Reworked User ID values scan after device is turn off/on.
  • Reworked Button I/O on-click event.
55.00.05.Rev.00
1.5.0_C.007
2020.02.13
  • Removed unnecessary Low Power parameters
  • Removed unnecessary Time Synchronization settings
  • Implemented On Demand tracking functionality
  • Removed unnecessary Number Check Settings panel
  • Implemented Event Notification functionality
  • Implemented User ID functionality
  • Improved BLE beacon functionality
  • Implemented Beacon List functionality
  • Improved User Interface configuration panel
  • Improved Keyboard configuration panel
  • Implemented Button IO feature
  • Updated default settings
  • Reworked User Interface configuration.
  • Reworked Keyboard configuration.
  • Implemented Event Notification panel.
  • Implemented Call After Answer functionality
  • Implemented User ID functionality.
  • Implemented On Demand data acquisition functionality.
  • Implemented Button IO Feature.
  • Optimized wake up from deep sleep by movement.
  • Updated default settings.
  • Improved BLE compatibility with beacons.