Changes

no edit summary
Line 1: Line 1: −
<font size="+3"><span style=color:#104996>'''Mounting recommendations'''</span></font>
+
<font size="+1"><span style=color:#104996>'''Mounting recommendations'''</span></font>
   −
<font size="+2"><span style=color:#F49E21> 1. </span> Connecting wires </font>
+
<font size="+1"><span style=color:#F49E21> 1. </span> Connecting wires </font>
 
<font size="+1">
 
<font size="+1">
 
* Wires should be connected while the module is not plugged in.
 
* Wires should be connected while the module is not plugged in.
Line 9: Line 9:  
* Wires cannot be connected to the board computers or control units.
 
* Wires cannot be connected to the board computers or control units.
 
</font>
 
</font>
<font size="+2"><span style=color:#F49E21> 2. </span> Connecting power source. </font>
+
<font size="+1"><span style=color:#F49E21> 2. </span> Connecting power source. </font>
 
<font size="+1">
 
<font size="+1">
 
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
 
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
Line 16: Line 16:  
* 3 A, 125 V external fuse shall be used.
 
* 3 A, 125 V external fuse shall be used.
 
</font>
 
</font>
<font size="+2"><span style=color:#F49E21> 3. </span> Connecting ignition wire. </font>
+
<font size="+1"><span style=color:#F49E21> 3. </span> Connecting ignition wire. </font>
 
<font size="+1">
 
<font size="+1">
 
* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
 
* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
Line 23: Line 23:  
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
 
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
 
</font>
 
</font>
<font size="+2"><span style=color:#F49E21> 4. </span> Connecting ground wire. </font>
+
<font size="+1"><span style=color:#F49E21> 4. </span> Connecting ground wire. </font>
 
<font size="+1">
 
<font size="+1">
 
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
 
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
Line 30: Line 30:  
</font><br />
 
</font><br />
   −
<font size="+3"><span style=color:#104996>'''{{{model|FMB2YX}}} installation instruction'''</span></font><br>
+
<font size="+1"><span style=color:#104996>'''{{{model|FMB2YX}}} installation instruction'''</span></font><br>
    
<font size="+1">
 
<font size="+1">
Line 56: Line 56:  
<br /><br />
 
<br /><br />
   −
<font size="+3"><span style=color:#FF0000>'''Safety information'''</span></font><br/>
+
<font size="+1"><span style=color:#FF0000>'''Safety information'''</span></font><br/>
<font size="+2">
+
<font size="+1">
 
This message contains information on how to operate {{{model|FMB20X}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/>
 
This message contains information on how to operate {{{model|FMB20X}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/>
 
The device uses SELV limited power source. The device uses a 6 V...30 V DC power supply.
 
The device uses SELV limited power source. The device uses a 6 V...30 V DC power supply.
Line 69: Line 69:       −
<font size="+3"><span style=color:#104996>'''Precautions'''</span></font>
+
<font size="+1"><span style=color:#104996>'''Precautions'''</span></font>
<font size="+2">
+
<font size="+1">
 
{| class="wikitable" style="border-style: solid; border-width: 0px"
 
{| class="wikitable" style="border-style: solid; border-width: 0px"
 
|+  
 
|+