Wiki Knowledge Base | Teltonika GPS

Changes

Template:FMB2 Possible mounting zones (view source)

Revision as of 14:34, 29 May 2018

731 bytes removed ,  14:34, 29 May 2018
no edit summary
Line 1: Line 1: −
<font size="+3"><span style=color:#104996>'''Mounting recommendations'''</span></font>
+
==<font size="+3"><span style=color:#104996>'''Trucks'''</span></font>==
   −
<font size="+2"><span style=color:#F49E21>Trucks</span></font>
+
<font size="+1">
−
 
  −
<font size="+2">
   
It is strongly recommended to mount FMB2YX outside of the vehicle with the sticker direction to the sky [[Image:Trucks.png|800px|right]]
 
It is strongly recommended to mount FMB2YX outside of the vehicle with the sticker direction to the sky [[Image:Trucks.png|800px|right]]
 
</font>
 
</font>
 +
<br /><br /><br /><br /><br /><br /><br /><br /><br /><br />
 +
 +
== ==
 +
<font size="+1">[[Image:Truck_Inside.png|800px|right]]
 +
Most commercial trucks have plastic hood in front of the vehicle. It is recommended to mount FMB2YX<br /></font>
 +
under the hood. Power cord output of the device should be at the bottom. If it is not possible,<br />
 +
if a front hood is made of some kind of metal, the device can be mounted inside the car on the front<br />
 +
panel as close as possible to the front window.
 +
 +
<br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br />
 +
 +
==<font size="+3"><span style=color:#104996>'''Tractors'''</span></font>==
   −
<font size="+2"><span style=color:#F49E21> 2. </span> Connecting power source. </font>
  −
<font size="+1">
  −
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
  −
* When the module is connected, measure the voltage again to make sure it did not decrease.
  −
* It is recommended to connect to the main power cable in the fuse box.
  −
* 3 A, 125 V external fuse shall be used.
  −
</font>
  −
<font size="+2"><span style=color:#F49E21> 3. </span> Connecting ignition wire. </font>
  −
<font size="+1">
  −
* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
  −
* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
  −
* Check if power is still available when you turn off any of vehicles devices.
  −
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
  −
</font>
  −
<font size="+2"><span style=color:#F49E21> 4. </span> Connecting ground wire. </font>
   
<font size="+1">
 
<font size="+1">
−
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
+
It is strongly recommended to mount FMB2YX outside of the vehicle with the sticker direction to the sky
−
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
  −
* For better contact scrub paint from the spot where loop is going to be connected.
   
</font>
 
</font>
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/13396...13443"