Difference between revisions of "Template:FMB2 Possible mounting zones"

From Wiki Knowledge Base | Teltonika GPS
(Created page with "<font size="+3"><span style=color:#104996>'''Mounting recommendations'''</span></font> <font size="+2"><span style=color:#F49E21> 1. </span> Connecting wires </font> <font si...")
 
 
(43 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
<font size="+3"><span style=color:#104996>'''Mounting recommendations'''</span></font>
+
==<font size="+3"><span style=color:#104996>'''Trucks'''</span></font>==
  
−
<font size="+2"><span style=color:#F49E21> 1. </span> Connecting wires </font>
 
 
<font size="+1">
 
<font size="+1">
−
* It is strongly recommended to mount FMB2YX outside of the vehicle with the sticker direction to the sky
+
It is strongly recommended to mount FMB2YX outside of the vehicle with the sticker direction to the sky [[Image:Trucks.png|800px|right]]
−
{| class="wikitable"
+
</font>
−
|+
+
<br /><br /><br /><br /><br /><br /><br /><br /><br /><br />
−
! style="width: 300px; background: black; color: white;" | Accessory and its description
+
 
−
! style="width: 500px; background: black; color: white;" | Accessory connection schematic
+
== ==
−
|-
+
<font size="+1">[[Image:Truck_Inside.png|800px|right]]
 +
Most commercial trucks have plastic hood in front of the vehicle. It is recommended to mount FMB2YX<br /></font>
 +
under the hood. Power cord output of the device should be at the bottom. If it is not possible,<br />
 +
if a front hood is made of some kind of metal, the device can be mounted inside the car on the front<br />
 +
panel as close as possible to the front window.
 +
 
 +
<br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br />
 +
 
 +
==<font size="+3"><span style=color:#104996>'''Tractors'''</span></font>==
  
−
! style="text-align: left; vertical-align: top;" | Fuel tank sensors
 
−
! style="text-align: left; vertical-align: top;" | Fuel sensor connection to {{{model|FMB20X}}}
 
−
|-
 
−
| style="text-align: left; vertical-align: top;" | A fuel tank level sensor which indicates the approximate fuel level on the driver's indicator panel exists in most cars. If the sensor returns analogue signal proportional to fuel level it can be connected to {{{model|FMB20X}}} Analog input. After connection to the tank fuel level sensor a calibration is needed because most fuel tank sensors are not linear. Calibration is performed by measuring voltage values resulting from the volume of fuel in tank.
 
−
| style="text-align: left; vertical-align: top;" | [[Image:Sch_fmb20x_lls.png|250px|center]]
 
−
|}
 
−
</font>
 
−
<font size="+2"><span style=color:#F49E21> 2. </span> Connecting power source. </font>
 
−
<font size="+1">
 
−
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
 
−
* When the module is connected, measure the voltage again to make sure it did not decrease.
 
−
* It is recommended to connect to the main power cable in the fuse box.
 
−
* 3 A, 125 V external fuse shall be used.
 
−
</font>
 
−
<font size="+2"><span style=color:#F49E21> 3. </span> Connecting ignition wire. </font>
 
−
<font size="+1">
 
−
* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
 
−
* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
 
−
* Check if power is still available when you turn off any of vehicles devices.
 
−
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
 
−
</font>
 
−
<font size="+2"><span style=color:#F49E21> 4. </span> Connecting ground wire. </font>
 
 
<font size="+1">
 
<font size="+1">
−
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
+
It is strongly recommended to mount FMB2YX outside of the vehicle with the sticker direction to the sky
−
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
 
−
* For better contact scrub paint from the spot where loop is going to be connected.
 
 
</font>
 
</font>

Latest revision as of 14:34, 29 May 2018

Trucks

It is strongly recommended to mount FMB2YX outside of the vehicle with the sticker direction to the sky

Trucks.png











Truck Inside.png

Most commercial trucks have plastic hood in front of the vehicle. It is recommended to mount FMB2YX
 under the hood. Power cord output of the device should be at the bottom. If it is not possible,
if a front hood is made of some kind of metal, the device can be mounted inside the car on the front
panel as close as possible to the front window.















Tractors

It is strongly recommended to mount FMB2YX outside of the vehicle with the sticker direction to the sky

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:FMB2_Possible_mounting_zones&oldid=13443"