Changes

no edit summary
Line 1: Line 1: −
==RS-485 interface==
+
==RS-232 / RS-485 interface==
 +
RS-232 supports only full-duplex communication, which means the data can be sent and also received at the same time.<br/>
 +
'''Note:''' In RS-232 LLS mode can be connected only one LLS fuel level sensor.<br/><br/>
   −
RS-485 supports only half-duplex communication, which means data is transferred only one way at a time.<br/>When activated RS-485 driver chip draws constant 30mA current, when entering Sleep or Deep sleep RS-485 will be powered off.
+
RS-485 supports only half-duplex communication, which means data is transferred only one way at a time.<br/>
 +
'''Note No. 1:''' In RS-485 LLS mode can be connected up to 5 LLS fuel level sensors.<br/>
 +
'''Note No. 2:''' when activated RS-485 driver chip draws a constant 30 mA current when entering Sleep or Deep sleep RS-485 will be powered off.
   −
===RS-485 modes===
+
==RS-232 / RS-485 modes==
* RS-485 receive (FMB silent) mode:
+
Available modes for RS-232 and RS-485 interfaces:
RS485 Works in receive mode. Support debug and testing commands. When command is received answer is sent after that it back up to Receive mode.<br/>
     −
* RS-485 transmit (FMB log) mode:
+
{| class="wikitable" style="text-align:center; background-color:#ffffff;"
RS-485 prints FMB device log and does not respond to commands.<br/>
+
|- style="text-align:left;"
 +
! rowspan="2" style="text-align:center; vertical-align:middle; font-weight:bold; background: #0054A6; color: white;" | Interface
 +
! colspan="18" style="text-align:center; background: #0054A6; color: white;" | Mode
 +
|-
 +
| Log Mode
 +
| NMEA
 +
| LLS
 +
| LCD
 +
| RFID HID
 +
| RFID MF7
 +
| Garmin FMI
 +
| TCP/UDP Ascii
 +
| TCP/UDP Binary
 +
| TCP/UDP Ascii Buffered
 +
| TCP/UDP Binary Buffered
 +
| UL202 Fuel Sensor
 +
| REC to LCD
 +
| ATOL Tachograph
 +
| Backup Sattelite
 +
|-
 +
| style="vertical-align:middle;" | RS-232
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
|-
 +
| style="vertical-align:middle;" | RS-485
 +
| ✔
 +
| ✔
 +
| ✔
 +
|
 +
|
 +
|
 +
|
 +
| ✔
 +
| ✔
 +
| ✔
 +
| ✔
 +
|
 +
|
 +
|
 +
|
 +
|}
   −
* RS-485 transmit (NMEA) mode:
+
{|
RS-485 prints GNSS NMEA log and does not respond to commands.<br/>
+
|[[File:Alert.png|left|link=|50px]]||<b>Do not under any circumstances connect RS485 A and B lines (or RS232 Tx and Rx) to power source.
 +
</b>
 +
|}
   −
* RS-485 receive (LLS) mode:
+
<br />
This mode supports up to five LLS fuel level sensors each of which has a receiver ID.<br/>
+
<tr>
 +
        <td style="vertical-align:middle;">[[Image:Bw_nb.png|50px]]</td>
 +
        <td style="vertical-align:middle;">Swapping RS485 A and B lines (or RS232 Tx and Rx) of the external device and also not connecting common ground first - May cause irreparable damage.</td>
 +
</tr>
 +
</table>
   −
* RS-485 TCP receive (ASCII/Binary) modes:
+
====Log mode====
In TCP ASCII/Binary mode a link with an external device using text messages can be established. Buffered modes save information until link with server is established and records are sent.
+
In this mode via RS-232 or RS-485 interface prints the {{{model|FMX640}}} device log and does not respond to commands.<br />
   −
* RS-485 receive (TCP ASCII/Binary Buffered) mode :
+
====GNSS NMEA mode====
RS485 works in receive mode. When data received from server RS485 is switched to transmit mode. If data server is not available, data will be saved in buffer.
+
In NMEA mode via RS-232 or RS-485 interface {{{model|FMX640}}} prints GNSS NMEA log and does not respond to commands.<br />
    +
====LLS mode====
 +
In LLS mode RS-232 supports one and RS-485 supports up to five LLS sensors - each of which has a receiver ID.<br/>
   −
==RS-232 Interface==
+
====TCP (ASCII/Binary) modes====
RS-232 supports full-duplex communication which means the data can be both sent and received at the same time as they use separate transmission lines. Most of the modes are the same as for {{{model|FMB640}}}.
  −
{{{model|FMB640}}} RS-232 connection diagram is shown on the figure above.
     −
===RS-232 modes===
+
In ''TCP Ascii/Binary'' mode all data received from the external device is sent directly to the server. Data is encapsulated in Codec 12 format. ''TCP Binary'' Mode has a delay of 30 ms, if no data is received for 30 ms, data is sent to the server. ''TCP Ascii'' mode waits for the End of Line (EOL) character (0x0D0A, \r\n, <CR><LF>) to pack data and send it to the server.
   −
Silent, Log mode, NMEA, LLS, TCP ASCII and TCP Binary modes are identical to those of FMBXXX RS-232 and RS-485 modes. In RS-232 LLS mode only one LLS fuel level sensor can be connected.
+
''TCP Ascii Buffered'' and ''TCP Binary Buffered'' modes are used to collect data from RS232 and save it in the buffer if there is no link with the server and data cannot be sent immediately. When the link is established and there is data to transmit, then RS232 data from the buffer is transmitted after all records are sent.
   −
* RS-232 LCD mode:
+
{| class="nd-othertables_2" style="width:100%;"
In this mode user is able to communicate with the server through terminal. A link between FMB device and the server has to be established for this mode to function properly.
+
|-
 +
!
 +
! TCP Binary/TCP ASCII mode
 +
! TCP Binary/TCP ASCII Buffered mode
 +
|-
 +
| '''Data is saved in buffer'''
 +
| No
 +
| Yes
 +
|-
 +
| '''Data sending protocol'''
 +
| Codec 12
 +
| Codec 13*
 +
|-
 +
| '''Timestamp'''
 +
| Not using
 +
| Is using*
 +
|-
 +
| '''To which server is sent'''
 +
| Main
 +
| Main and backup
 +
|}
 +
''*If the Timestamp parameter is enabled, then Codec 13 is used for data sending. Otherwise, Codec 12 is used.''
 +
<br></br>
   −
* RS-232 RFID HID/RFID MF7 mode:
+
=====Message Timestamp=====
The difference between ''RFID HID Mode'' and ''RFID MF7 Mode'' is that in ''RFID HID Mode'' {{{model|FMB640}}} understands RFID messages that are in hexadecimal format and ''RFID MF7 Mode'' interpretes messages that are in decimal format. The type of RFID message sent to {{{model|FMB640}}} depends on the RFID reader. For example, ''RFID HID'' mode message looks like "$aa$02$03$04$17$89$00$01" while ''MF7 mode'' message is of following format: "1213141519".<br/>The selected mode has to correspond to the RFID reader's mode.<br/>Please contact your local sales representative for more information about RFID IDs and devices.
+
[[File:Timestamp.gif|right]] Message Timestamp parameter is used to determine if it is necessary to include a timestamp in the RS-232 TCP packet when sending to the server. If the parameter is Enabled, then Codec 13 is used for data sending. Otherwise, Codec 12 is used.
   −
* ATOL Tachograph mode: This mode is used to connect ATOL tachograph
+
===== RS-232 / RS-485  CMD ID=====
 +
This parameter is used when {{{model|}}} is sending RS232/RS485 packet to a server, it overrides command type value in Codec12/Codec13 with user-defined CMD ID value (1 - 14). {{{model|}}} behavior when it receives different CMD ID (Type) values in GPRS packet from server.
 +
[[File:CMD.gif|right]]
   −
* UL202-2 Fuel Sensor: Select this mode to make Ultrasonic Fuel Sensors to work on COM port.
+
==RS-232 modes==
 +
Below you will find descriptions of available modes only for RS-232 interface:
   −
* RS-232 Garmin mode:
+
====RS-232 LCD mode====
Garmin provides a Fleet Management Interface Tool Kit, once {{{model|FMB640}}} is connected to the navigator it enables the driver to have a "screen" in their vehicle for real-time navigation and messaging, and offers job dispatch capabilities to help them be more efficient.<br/>{{{model|FMB640}}} and Garmin operational diagram is shown on the figure below.
+
In this mode, the user is able to communicate with the server through the terminal. A link between the {{{model|FMB640}}} device and the server has to be established for this mode to function properly.
{{{image|[[Image:FMB640_garmin_block.png|800px|center]]}}}
+
 
 +
To communicate from terminal to server - in terminal send command "WT^W your text here"
 +
To communicate with the server to the terminal - send "#DO DAT=you text here" packet in [https://wiki.teltonika-gps.com/view/Teltonika_Data_Sending_Protocols#Codec_12 Codec12 protocol]
 +
 
 +
====RS-232 RFID HID/RFID MF7 mode====
 +
Radio-frequency identification (RFID) is the use of a wireless non-contact system that uses radio-frequency electromagnetic fields to transfer data from a tag attached to an object, for the purposes of automatic identification and tracking. [[{{{model|FMB640}}}]] can be configured in a way to use with an RFID reader. When an RFID of some sort (typically a plastic card with a magnetic line) is used with an RFID reader that is connected to [[{{{model|FMB640}}}]], the device creates a record with the data that the RFID reader has read and can be sent to a server with all other information. RFID ID is activated  like an I/O parameter:
 +
<br>
 +
[[image:FMB640_RS232_RFID.png]]
 +
<br>
 +
To set up [[{{{model|FMB640}}}]] so it can be connected to an RFID reader, some parameters have to be set up. Go to RS232 \ RS485 and set up COM1 or COM2 settings to RFID Mode or RFID MF7 Mode (the used mode depends on the mode that the RFID reader works). See Figure 922. The Baudrates for each mode are:
 +
* '''''RFID Mode''''' – 57600
 +
* '''''RFID MF7 Mode''''' – 9600
 +
[[image:FMB640_RS232_RFIDconf.png]]<br>
 +
The difference between RFID HID Mode and RFID MF7 Mode is that in RFID MF7 Mode [[{{{model|FMB640}}}]] understands RFID messages that are in hexadecimal text format and RFID HID Mode interprets messages that are in binary format. The type of RFID message sent to [[{{{model|FMB640}}}]] depends on the RFID reader. For example, the RFID MF7 mode message looks like $aa$02$03$04$17$89$00$01 while the HID mode message is of the following format: "1213141519".
 +
The selected mode has to correspond to the RFID reader's mode.
 +
Please contact your local sales representative for more information about RFID IDs and devices.
 +
 
 +
====REC to LCD mode====
 +
In this mode, records are sent via ports.
 +
This is an example view that is displayed in Terminal:
 +
 
 +
[[File:rec-lcd.jpg]]
 +
 
 +
====ATOL Tachograph mode====
 +
This mode is used to connect the ATOL tachograph.
 +
 
 +
====UL202-2 Fuel Sensor====
 +
Select this mode to make [[UL202 Ultrasonic Fuel Sensor|Ultrasonic Fuel Sensors]] work on the COM port.
 +
 
 +
====Satellite Backup mode====
 +
Since 00.02.05 firmware version device supports [[TSM232|Iridium devices]] which can send short burst data (SBD) to the server. This means that some data can be sent from the FM device to the server through satellites.
 +
In order to get those records, you have to connect the device to [[{{{model|FMB640}}}]] COM1 or COM2 port. Select COM1 or COM2 mode Satellite backup mode. Those settings could be found in RS232/RS485 tab in the configurator. Baudrate for satellite devices is 19200 bps. Furthermore, [[TSM232]] functionality should be enabled. These settings can be found in the Features tab in Short burst data settings. So, with this mode, some data can be sent from the FM device to the server through satellites using [[TSM232|Iridium devices]].
 +
 
 +
====RS-232 Garmin mode====
 +
Garmin provides a Fleet Management Interface Tool Kit, once [[{{{model|FMB640}}}]] is connected to the navigator it enables the driver to have a "screen" in their vehicle for real-time navigation and messaging and offers job dispatch capabilities to help them be more efficient.<br/>[[{{{model|FMB640}}}]] and Garmin operational diagram is shown in the figure below:
 +
{{{image|[[Image:FMB640_GARMIN_BLOCK.png|800px|center]]}}}
 +
 
 +
Garmin configuration is shown in the figure below: <br>
 +
[[image:FMB640_RS232_Garmin.png]]
 +
 
 +
==LLS Sensor==
 +
LLS sensor series liquid level sensors are solid-state capacitive devices with no moving parts. The sensors use capacitive technology to produce accurate liquid level measurements of standard factory-grade DIESEL OIL and PURE GASOLINE (BENZINE) carbon fuels. The LLS sensor liquid level sensors are strictly prohibited to use in any liquids which are not factory-grade carbon fuels or contain: BIOFUEL, METHANOL, ETHANOL, UREA, and similar aggressive components in pure form or as additives for factory-grade carbon fuels for use in INTERNAL COMBUSTION ENGINES. Operating media – Diesel fuel (oil), pure gasoline (benzene). <br>
 +
In order to use the LLS fuel counter, the newest firmware version is needed which can be obtained from Teltonika or a representative. Firmware is updated over GPRS or using a cable update method. <br>
 +
 
 +
 
 +
====Specifications====
 +
 
 +
 
 +
<table class="nd-othertables_2" style="width:40%;">
 +
<tr>
 +
        <th rowspan="1" style="width:70%; vertical-align: middle; text-align: center;">Parameter</th>
 +
        <th rowspan="1" style="width:30%; vertical-align: middle; text-align: center;">Value</th>
 +
    </tr>
 +
<tr>
 +
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Supply voltage</th>
 +
        <td style="vertical-align: middle; text-align: left; ">+10..+50 V</td>
 +
    </tr>
 +
<tr>
 +
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Current consumption, mA (for 12/24 V)</th>
 +
        <td style="vertical-align: middle; text-align: left; ">25 mA / 50 mA</td>
 +
    </tr>
 +
<tr>
 +
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Working temperature</th>
 +
        <td style="vertical-align: middle; text-align: left; ">-40..+85 ºC</td>
 +
    </tr>
 +
<tr>
 +
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Working mode</th>
 +
        <td style="vertical-align: middle; text-align: left; ">Continuous</td>
 +
    </tr>
 +
<tr>
 +
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Weight</th>
 +
        <td style="vertical-align: middle; text-align: left; ">< 2.0 kg</td>
 +
    </tr>
 +
<tr>
 +
        <th style="border-bottom: 1px solid #E8E8E8; vertical-align: middle; text-align: left; color:black">Working pressure</th>
 +
        <td style="vertical-align: middle; text-align: left; ">Atmospheric</td>
 +
    </tr>
 +
</table>
 +
 
 +
 
 +
====Wiring And Configuration====
 +
 
 +
 
 +
First of all, the LLS fuel sensor must be connected to the [[{{{model|FMB640}}}]] device. Please find examples below:
 +
<table class="nd-othertables_2" style="width:100%;">
 +
<tr>
 +
        <td style="vertical-align: middle; text-align: left; ">'''Using RS232 socket'''</th>
 +
        <td style="vertical-align: middle; text-align: left; ">'''Using RS485 socket'''</td>
 +
    </tr>
 +
<tr>
 +
        <td style="vertical-align: middle; text-align: left; ">[[Image:FMX6 ir LLS sensor pajungimo schema RS232 WIKI V1.2.png|575px]]</th>
 +
        <td style="vertical-align: middle; text-align: left; ">[[Image:FMX6 ir LLS sensor pajungimo schema RS485 WIKI V1.0.png|585px]]</td>
 +
    </tr>
 +
<tr>
 +
</table>
 +
 
 +
Then [[{{{model|FMB640}}}]] must be configured. Both fuel level and fuel temperature has to be set up by the configurator’s I/O menu: <br>
 +
[[image:FMB640_RS232_LLSmenu.png]]
    
==Garmin protocols==
 
==Garmin protocols==
The following is a list of protocols supported and the corresponding list of features/benefits. {{{model|FMB640}}} can fully support Fleet Management Interface (FMI) versions up to 2.1. Other or higher versions may be supported, but Teltonika is not responsible for the changes made by Garmin, which may affect the function of {{{model|FMB640}}} and Garmin products. For more information about Garmin products and FMI versions, please refer to http://www8.garmin.com/solutions/pnd/supportedproducts.jsp. Notice that some Garmin products use different connection cables than others.
+
The following is a list of protocols supported and the corresponding list of features/benefits. [[{{{model|FMB640}}}]] can fully support Fleet Management Interface (FMI) versions up to 2.1. Other or higher versions may be supported, but Teltonika is not responsible for the changes made by Garmin, which may affect the function of [[{{{model|FMB640}}}]] and Garmin products. For more information about Garmin products and FMI versions, please refer to https://www.garmin.com/en-US/fleet-ready-navigators/. Notice that some Garmin products use different connection cables than others.
 
  −
===Standard protocols===
      +
====Standard protocols====
 
Text Message Protocol:
 
Text Message Protocol:
* Allows text messages sent to the device to be displayed in "inbox" on navigation unit;
+
* Allows text messages sent to the device to be displayed in "inbox" on the navigation unit;
* Garmin can provide a confirmation that message was read;
+
* Garmin can provide a confirmation that the message was read;
 
* Garmin can also provide a yes/no box below the text of the message to enable a quicker response;
 
* Garmin can also provide a yes/no box below the text of the message to enable a quicker response;
 
* Messages can be up to 199 characters long;
 
* Messages can be up to 199 characters long;
* Messages can also be generated from device and sent to dispatcher/office;
+
* Messages can also be generated from the device and sent to dispatcher/office;
* Messages received will be notified to driver through a pop-up alert on Garmin screen;
+
* Messages received will be notified to the driver through a pop-up alert on the Garmin screen;
 
* Garmin provides a "virtual keyboard" for text communication.
 
* Garmin provides a "virtual keyboard" for text communication.
    
Stop (Destination) Protocol:
 
Stop (Destination) Protocol:
 
* Garmin can display a list of Stops/Jobs reported to the device in a separate category called "My Stops";
 
* Garmin can display a list of Stops/Jobs reported to the device in a separate category called "My Stops";
* Driver has ability to navigate directly to Stop from the list;
+
* Driver has the ability to navigate directly to Stop from the list;
* Garmin can provide status of a current Stop in progress;
+
* Garmin can provide the status of a current Stop in progress;
 
* Garmin can indicate whether the driver has stopped at the location;
 
* Garmin can indicate whether the driver has stopped at the location;
 
* Garmin can inform how far the driver has progressed through the list of Stops;
 
* Garmin can inform how far the driver has progressed through the list of Stops;
* Garmin can provide confirmation that the driver has received a particular Stop, familiarized himself/herself with its details or removed it from the list;
+
* Garmin can provide confirmation that the driver has received a particular Stop, familiarized himself/herself with its details, or removed it from the list;
 
* Can provide confirmation that a Stop has been reached.
 
* Can provide confirmation that a Stop has been reached.
   Line 73: Line 256:     
Auto-Arrival at Stop Protocol:
 
Auto-Arrival at Stop Protocol:
* This feature is used to tell Garmin PND to automatically detect that it has arrived at a Stop and then to prompt the driver if he/she would like to mark the Stop as done and begin navigating to a next Stop on the list;
+
* This feature is used to tell Garmin PND to automatically detect that it has arrived at a Stop and then to prompt the driver if he/she would like to mark the Stop as done and begin navigating to the Next Stop on the list;
 
* Auto-arrival can be determined by how long the unit is stopped close to the destination (in the case driver has to park and walk) or by how close the unit needs to be to the destination before the Auto-arrival feature is activated.
 
* Auto-arrival can be determined by how long the unit is stopped close to the destination (in the case driver has to park and walk) or by how close the unit needs to be to the destination before the Auto-arrival feature is activated.
    
Data Deletion Protocol:
 
Data Deletion Protocol:
 
* Dispatcher/office has the ability to wipe clean the data on Garmin PND;
 
* Dispatcher/office has the ability to wipe clean the data on Garmin PND;
* It allows to clean messages in inbox and remove stops.
+
* It allows to clean messages in the inbox and remove stops.
 
  −
===Enhanced protocols===
      +
====Enhanced protocols====
 
Canned Responses/Messages:
 
Canned Responses/Messages:
 
* Fleet managers can communicate by sending up to 200 "canned" responses from the server to be stored directly on Garmin devices;
 
* Fleet managers can communicate by sending up to 200 "canned" responses from the server to be stored directly on Garmin devices;
* Up to 50 of these canned responses can be utilized for any given scenarios;
+
* Up to 50 of these canned responses can be utilized for any given scenario;
 
* Drivers can store up to 120 canned messages, eliminating the need to type while driving.
 
* Drivers can store up to 120 canned messages, eliminating the need to type while driving.
    
Status Protocol:
 
Status Protocol:
 
* Up-to-the-minute communications that allow drivers to automatically send status updates;
 
* Up-to-the-minute communications that allow drivers to automatically send status updates;
* Driver's units can store up to 16 status indicators such as start/stop shift, on/off break etc.
+
* Driver's units can store up to 16 status indicators such as start/stop shift, on/off the break, etc.
   −
===Supported features on TAVL client application===
+
====Supported features on TAVL client application====
TAVL client application lets user use the following features of Garmin FMI:
+
TAVL client application lets the user use the following features of Garmin FMI:
 
* Text messaging;
 
* Text messaging;
 
* Destination message;
 
* Destination message;
 
* ETA request.
 
* ETA request.
   −
===Text messaging===
+
====Text messaging====
Text messaging feature lets user communicate with the driver (user that operates Garmin device) by sending text messages via GPRS.
+
The text messaging feature lets users communicate with the driver (the user that operates the Garmin device) by sending text messages via GPRS.
   −
===Destination message===
+
====Destination message====
Destination message is used to inform the driver of a new destination. When Garmin device receives a destination message from the server it displays it as a Stop to the driver and also gives the driver an ability to start navigating to the Stop location. New destination in TAVL client is represented as a Geozone so a new Geozone (as destination) has to be created first.
+
A destination message is used to inform the driver of a new destination. When the Garmin device receives a destination message from the server it displays it as a Stop to the driver and also gives the driver the ability to start navigating to the Stop location. A new destination in the TAVL client is represented as a Geozone so a new Geozone (as destination) has to be created first.
   −
===ETA request message===
+
====ETA request message====
''Estimated Time of Arrival'' request message is used when user wants to know an expected arrival time to currently active destination and the distance (in meters) from current object location to the destination.
+
''Estimated Time of Arrival'' request message is used when the user wants to know an expected arrival time to the currently active destination and the distance (in meters) from the current object location to the destination.

Navigation menu