Wiki Knowledge Base | Teltonika GPS

Changes

Template:FMB640 System settings (view source)

Revision as of 08:31, 11 October 2023

8,719 bytes added ,  08:31, 11 October 2023
no edit summary
Line 1: Line 1: −
System settings have following configurable parameters:
+
System settings have the following configurable parameters:
−
System settings have 14 configurable parameters:
  −
*Sleep settings, where user can choose sleep mode;
  −
*GNSS Source, where user can pick any or all satellite systems to use. More selections might improve tracking quality
  −
*Analog Input value range, where user can choose analog input range 10 V or 30 V (10 V range for now works same as 30 V range).
  −
*AIN4/DOUT4 Mode, user can select on of 2 options to define which way 18th pin (from Figure 5) will work.
  −
*J1708 settings used to enable/disable following vehicle bus standard used for communication.
  −
*Odometer Source settings, where user can select one of the options for odometer counting. There are 5 possible options: GNSS, LVCAN, ALLCAN, FMS and KLINE.
  −
*Speed source settings are used to declare what technology will be used for vehicle speed measurement
  −
*Records Settings, where user can enable or disable records when GPS is not available (no time synchronization). There are additional parameters for records saving: memory selection and sorting option to define where records will be saved and in what order they will be sent.
  −
*Open Link Timeout is used to set timeout of link between FMB640 and AVL application termination. If FMB640 has already sent all records it waits for new records before closing link (except Deep Sleep mode, more information in Deep Sleep mode chapter). If new records are generated in the period of this timeout, and minimum count of timer to send is reached, they are sent to AVL application. This option is useful when GSM operator charge money for link activation.
  −
*Server Response Timeout is used to set time period waiting for response from server side.
  −
*Ping mode, where user can enable and select how frequent device will send packets to inform server about active data link. It works when device did not send any records to server in defined time period.
  −
*Static navigation settings, where user can turn static navigation on or off. Additional, user can chose from what source (movement or ignition) static navigation can be deactivated/activated. Static Navigation Mode is a filter, which filters out track jumps when the object is stationary. If Static navigation filter is disabled, it will apply no changes on GPS data. If Static navigation filter is enabled, it will filter changes in GPS position if no movement (configured movement source) or ignition (configured ignition source) is detected (depends on what static navigation settings is selected: movement, ignition or both sources). It allows filtering GPS jumps when object is parked (is not moving) and GPS position is still traced.
  −
*Ignition source, where user can choose between power voltage, digital input 1, digital input 2, digital input 3, digital input 4 and accelerometer as ignition sources. More than one ignition source can be selected at the same moment. User can select movement start and movement stop delay time (in seconds): those parameters are used when ignition source is accelerometer.
  −
*Time synchronization settings, where user can choose from what source (or sources) FMB640 time will be synchronized. User has choice to use only one synchronization source by GNSS. When selected synchronization from NTP, time will be synchronized from NTP server and from GNSS. When selected synchronization from NITZ, time will be synchronized from GSM operator and GNSS. When selected synchronization from NITZ+NTP, time will be synchronized from all three sources (if it is necessary). Every time GNSS fix will be acquired time will be synchronized (if needed). User can select from what NTP server (possible to configure two servers) time will be synchronized, as well as delay after which time synchronization from non-GNSS source will begin.
     −
''Static Navigation'' mode is a filter, which filters out track jumps when the object is stationary. If static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement (as defined by configured movement source) or ignition (as defined by configured ignition source) is detected. It allows filtering GPS jumps when the object is parked (not moving) and GPS position is still traced.
+
==Sleep Mode==
   −
{{{pic_system|[[Image:FMB640_System.png|800px|center]]}}}
+
[[Image:FMB640 Sleep mode.png|right|300px]]
   −
In ''GNSS Source'' settings user can configure which GNSS system(s) to use.<br/>User has a choice to use only one system between GPS and GLONASS or it is possible to choose both. Examples of non-configurable GNSS source are:
+
This feature will be used to save power consumption of external battery (power supply). It let the user choose one of four power saving modes which he would prefer: '''[[{{{model|FMB1YX}}} Sleep modes#GPS Sleep mode|GPS Sleep]]''', '''[[{{{model|FMB1YX}}} Sleep modes#Deep Sleep mode|Deep Sleep]]''' and '''[[{{{model|FMB1YX}}} Sleep modes#Online Deep Sleep mode|Online Deep Sleep]]'''. Also, after the mentioned options you can find the Timeout (min) parameter which starts counting when the device is in STOP mode. After timeout is reached and all conditions for sleep mode are met, the device goes to sleep mode. <br><br>
−
* GLONASS + GPS;
+
'''Note:''' Detail description and conditions about every mode you can find [[{{{model|FMB1YX}}} Sleep modes|'''here''']].<br><br><br><br>
−
* GLONASS;
  −
* GPS;
     −
{| class="wikitable"
+
===BT/BLE module OFF during Sleep modes===
−
|+
+
------------------
−
! style="width: 250px; background: black; color: white;" | Selected source(s)
+
Power off sleep mode can be described as the lowest possible power consumption mode where the device can go into power off state.
−
! style="width: 100px; background: black; color: white;" | ID
+
<br>
−
|-
+
 
−
! style="text-align: left; vertical-align: top;" | GPS only
+
From the version, 03.28.XX this new functionality includes new parameters:
−
| style="text-align: left; vertical-align: top;" | 1
+
 
−
|-
+
*'''Periodic Wakeup''' – if value is greater than zero, device while being in Deep Sleep or Online Deep Sleep, will wake up after defined period for beacon collection. This is mainly should be used when Bluetooth is disabled in sleep.
−
! style="text-align: left; vertical-align: top;" | GLONASS only
+
*'''Bluetooth On While In Sleep'''- by default this parameter value is set to Enable and BT will work as in base functionality. If this value is set to Disable, Bluetooth will be turned off when device goes to Deep Sleep or Online Deep Sleep and will be turned on during Periodic Wakeup or if device enters normal state.
−
| style="text-align: left; vertical-align: top;" | 2
+
[[Image:PWU.jpg|right|300px]]
−
|-
+
</br></br>
−
! style="text-align: left; vertical-align: top;" | GPS + GLONASS
+
 
−
| style="text-align: left; vertical-align: top;" | 3
+
Note: In case when during scan after wakeup no BLE devices will be found FMB will be active for configured scan duration time in Bluetooth 4.0 tab. After that timeout FMB will go to sleep state.
−
|-
+
<br>
−
|}
+
 
 +
Power off sleep mode can be described as the lowest possible power consumption mode where the device can go into power off state and can only wake up if one of the conditions is true:
 +
 
 +
*Movement is detected by accelerometer (not by the configured movement source);
 +
*External power is applied;
 +
*It is the time to make a new periodic record (new feature);
 +
<br>
 +
Please keep a note that Power OFF Sleep will not work if any USB cable is connected to the device.
 +
 
 +
==System Settings==
 +
 
 +
===Movement Source===
 +
---------------
 +
[[Image:Movement source.png|right|300px]]
 +
Parameter, which determines if the device should work in "Vehicle on Stop" or "Vehicle on Moving" mode. There are four possible movement sources<br>
 +
 
 +
*'''Ignition''' - if Ignition (based on Ignition Source) is ON, Vehicle MOVING mode is used; if Ignition is OFF, Vehicle on STOP mode is used;
 +
*'''Movement''' - if the accelerometer detects movement, Vehicle MOVING mode is used; if no movement is detected, Vehicle on STOP mode is used;
 +
*'''GNSS''' - if GPS Fix is acquired and the vehicle speed is >=5 km/h, Vehicle MOVING mode is used; if GPS speed is <5 km/h, Vehicle on STOP mode is used (if there is no GPS Fix, accelerometer determines vehicle modes);
 +
*'''CAN Speed''' - if CAN adapter or FMS speed is >0 km/h, Vehicle MOVING mode is used; if CAN adapter or FMS speed is <=0 km/h, Vehicle on STOP mode is used;
 +
 
 +
===GNSS Source===
 +
------------------
 +
In ''GNSS Source'' settings user can configure which GNSS system(s) to use.<br />User has a choice to use only one system GPS and it is possible to choose two or three systems together. One exception is that you cannot combine BeiDou and GLONASS systems together. Examples of non-configurable GNSS source combinations are:
 +
 
 +
[[Image:GNSS source.png|right|300px]]
 +
 
 +
*GPS + Galileo;
 +
*GLONASS + BeiDou;
 +
*Galileo + BeiDou;
 +
*Galileo + GLONASS;
 +
*GPS + GLONASS + BeiDou;
 +
*GPS + Galileo + BeiDou;
 +
*Galileo + GLONASS + BeiDou;
 +
*GPS + Galileo + GLONASS + BeiDou.<br><br>
 +
 
 +
'''List of configurable GNSS sources:'''
 +
 
 +
*GPS only
 +
*GPS + BeiDou
 +
*GPS + GLONASS
 +
*GPS + Galileo + GLONASS
 +
 
 +
===Battery Charge Mode===
 +
------------------
 +
In ''Battery Charge Mode'' settings user can choose when the battery will be charged.<br>
 +
 
 +
[[Image:FMB640 Battery Charge Mode.png|right|300px]]
 +
 
 +
Possible options:
 +
 
 +
*'''On Need''' - enable battery charger any time when needed;
 +
*'''After Ignition ON''' - charger can be enabled after ignition is turned on, except if the battery is fully charged or 10-minute timeout has not passed since the device was turned on for faster FIX receiving;
 +
 
 +
===Analog Input value range===
 +
------------------
 +
 
 +
[[Image:Analog input value range.png|right|300px]]
 +
 
 +
In ''Analog Input Value Range'' settings user can choose an analog input range of 10 V or 30 V.<br><br>
 +
 
 +
===AIN4/DOUT4 Mode===
 +
------------------
 +
 
 +
[[Image:FMB640_AIN4_DOUT4_Mode.png|right|300px]]
 +
 
 +
Users can select one of 2 options to define which way the 18th PIN will work. Configurable options are DOUT4 and AIN4.<br><br>
 +
'''Note:''' ''DOUT4 can be used for relay control, however it is not recommended to use it with low current peripheral devices such as LEDs as they may stay turned on in DOUT4 "OFF" state. (Due to interface properties up to 100 uA leakage current is feasible on 18th pin when DOUT4 is turned "OFF").''
 +
 
 +
===Analog Input value range 3-4===
 +
------------------
 +
 
 +
[[Image:FMB640 analog input range 3 4.png|right|300px]]
 +
 
 +
In ''Analog Input Value Range'' settings user can choose an analog input range of 10 V or 30 V for AIN3 and AIN4.<br><br>
 +
 
 +
===Odometer Source settings===  
 +
------------------
 +
 
 +
[[Image:FMB640 Odometer Source settings.png|right|300px]]
 +
 
 +
In ''Odometer Source settings'' a user can select one of the options for odometer counting. There are 4 possible options:  
 +
 
 +
*GPS
 +
*LVCAN
 +
*FMS
 +
*KLINE
 +
 
 +
===Speed source settings===
 +
------------------
 +
 
 +
[[Image:FMB640 Speed source settings.png|right|300px]]
 +
 
 +
In ''Speed Source settings'' a user can declare what technology will be used for vehicle speed measurement. There are 4 possible options:
 +
 
 +
*GPS
 +
*LVCAN
 +
*FMS
 +
*KLINE
 +
 
 +
==IO Global Settings==
 +
 
 +
[[Image:FMB640 IO Global Settings.png|right|300px]]
 +
 
 +
In ''IO Global settings'' a user can set IO value if I/O is not present for 30 seconds. <br>
 +
A user can choose how the device will send this IO element: <br />
 +
 
 +
*'''Don't Send''' - IO element is not included in the packet until new data is acquired;
 +
*'''Send Zero''' - Zero value is sent until new data is acquired;
 +
*'''Send Last Know Value''' - Last known value is sent until new data is acquired;
 +
*'''Send 0xFF''' - 0xFF value is sent until new data is acquired;
 +
 
 +
==Protocol Settings==
 +
 
 +
[[Image:Data Protocol.png|right|300px]]
 +
 
 +
In ''Data Protocol'' settings user can choose which protocol version ('''[[Codec#Codec 8|Codec 8]]''' or '''[[Codec#Codec 8 Extended|Codec 8 Extended]]''') will use for data sending to the server.<br><br>
 +
 
 +
==Records Settings==
 +
 
 +
===Recors Saving/Sending Without TS===
 +
------------------
 +
 
 +
This feature will be used to save and send records to the server without time synchronization.<br>
 +
 
 +
[[Image:Records saving sending without TS.png|right|300px]]
 +
 
 +
Possible options:
 +
 
 +
*'''After Position Fix''' - records will be saved and send only after position fix;
 +
*'''After Time Sync''' - records will be saved and send only after time synchronization;
 +
*'''Always''' - records will be always saved and send even if will not be time synchronization.
 +
 
 +
'''Note:''' ''If record is without valid coordinates – (there were no GPS fix in the moment of data acquisition) – Longitude, Latitude and Altitude values are last valid fix, and Angle, Satellites, and Speed are 0. After a reboot, it will send zero coordinates.''
 +
 
 +
===Open Link Timeout===
 +
------------------
 +
 
 +
[[Image:Open link timeout.png|right|300px]]
 +
 
 +
This feature is used to set a timeout of the link between [[{{{model|FMB640}}}]] and AVL application termination. If [[{{{model|FMB640}}}]] has already sent all records it waits for new records before closing link (except '''[[{{{model|FMB640}}} Sleep modes#Deep Sleep mode|Deep Sleep]]''' mode, more information in '''[[{{{model|FMB640}}} Sleep modes#Deep Sleep mode|Deep Sleep]]''' mode chapter). If new records are generated in the period of this timeout, and the minimum count of the timer to send is reached, they are sent to AVL application. This option is useful when a GSM operators charge money for link activation.
 +
 
 +
===Response Timeout===
 +
------------------
 +
 
 +
[[Image:Response Timeout.png|right|300px]]
 +
 
 +
This feature is used to set a time period waiting for a response from the server-side.
 +
 
 +
===Sort By===
 +
------------------
 +
 
 +
[[Image:Sort By.png|right|300px]]
 +
 
 +
This feature is used to set sort records sending sequence. Possible options:
 +
 
 +
*'''Newest''' - sends records from newest to oldest. High priority records are sent to the server immediately;
 +
*'''Oldest''' - sends records from oldest to newest. High priority records are sent to the server immediately.
 +
 
 +
===Save records to===
 +
------------------
 +
 
 +
[[Image:Save records to.png|right|300px]]
 +
 
 +
This feature is used to select where to save records which are not sent yet. Possible options:
 +
 
 +
*Internal memory;
 +
*SD card.
 +
 +
===Ping mode===
 +
------------------
 +
 
 +
[[Image:Ping mode.png|right|300px]]
 +
 
 +
The user can enable and select how frequent devices will send packets to inform the server about the active data link. It works when the device did not send any records to the server in a defined time period. <br><br><br><br>
 +
 
 +
===Network Ping Timeout===
 +
------------------
 +
 
 +
[[Image:Network ping timeout.png|right|300px]]
 +
 
 +
This feature is used to set network ping after a timeout to prevent link close by the operator.
 +
 
 +
==Static Navigation Settings==
 +
 
 +
[[Image:FMB640_Static_navigation_settings.png|right|300px]]
 +
 
 +
''Static Navigation Mode'' is a filter, which filters GPS jumps when an object is parked (is not moving) and GPS position is still traced.<br><br>
 +
If the Static navigation filter is disabled, it will apply no changes to GPS data. If the Static navigation filter is enabled:
 +
 
 +
*'''Movement OR Ignition''' - filter changes in GPS position if no movement (configured movement source)or ignition (configured ignition source) is detected;
 +
*'''Movement''' - filter changes in GPS position if no movement (configured movement source) is detected;
 +
*'''Ignition''' - filter changes in GPS position if ignition (configured ignition source) is detected;
 +
*'''Movement''' AND Ignition - filter changes in GPS position if no movement (configured movement source) and ignition (configured ignition source) is detected.
 +
 
 +
If the user chooses Movement OR Ignition (default setting), static navigation will be deactivated, when movement or ignition is detected. If the user chooses Movement, static navigation will be deactivated, only when movement is detected. If the user chooses Ignition, static navigation will be deactivated, only when the ignition is detected. If the user chooses Movement AND Ignition, static navigation will be deactivated, when both movement and ignition are detected. Parameter values for each source are described in the table below.
 +
 
 +
''Static Navigation'' mode is a filter, which filters out track jumps when the object is stationary. If the static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement (as defined by configured movement source) or ignition (as defined by configured ignition source) is detected. It allows filtering GPS jumps when the object is parked (not moving) and GPS position is still traced.
 +
 
 +
==Ignition Source==
 +
 
 +
[[Image:FMB640 Ignition source.png|right|300px]]
 +
 
 +
Ignition source will be used to determine the ignition of the vehicle. If voltage is between High Voltage Lever and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON. If voltage is higher than High Voltage Lever or lower than Low Voltage Level - ignition is OFF.<br>
 +
 
 +
*'''Digital Input 1''' - if ''Digital Input 1'' is 1 - ignition is ON; if ''Digital Input 1'' value is 0 - ignition is OFF;
 +
*'''Digital Input 2''' - if ''Digital Input 2'' is 1 - ignition is ON; if ''Digital Input 2'' value is 0 - ignition is OFF;
 +
*'''Digital Input 3''' - if ''Digital Input 3'' is 1 - ignition is ON; if ''Digital Input 3'' value is 0 - ignition is OFF;
 +
*'''Digital Input 4''' - if ''Digital Input 4'' is 1 - ignition is ON; if ''Digital Input 4'' value is 0 - ignition is OFF;
 +
*'''Power Voltage''' - if the voltage is between High Voltage Lever and Low Voltage Level (below ''Ignition Settings'' options) - ignition is ON; if the voltage is higher than High Voltage Lever or lower than Low Voltage Level - ignition is OFF.
 +
*'''Movement''' - if ''Movement'' is still detect 1 after ''Movement Start Delay (s)'' - ignition is ON; if ''Movement'' value is 0 after ''Movement Stop Delay (s)'' - ignition is OFF;
 +
 
 +
'''Example:''' DIN1 and Movement are selected as the Ignition source. When the device detects movement, Ignition status will change to 1, regardless that the DIN1 value is 0.
 +
 
 +
==Time Synchronization Settings==
 +
 
 +
[[Image:Time synchronization older.png|right|300px]]
 +
 
 +
''Synchronization settings'' is used for choosing the device’s internal time synchronization source. Possible options are:
 +
 
 +
*'''GPS Only''' - time synchronization by GPS;
 +
*'''NITZ and NTP''' - time synchronization from GSM operators (NITZ) and/or web server (NTP);
 +
*'''NTP''' - time synchronization from NTP server only;
 +
*'''NITZ''' - time synchronization from GSM operators (NITZ).
 +
 
 +
''NTP Resync'' parameter determines how often a device should resynchronize its time. If the set value is not equal to zero, time resynchronization will occur periodically at time intervals to which this parameter is set.<br>
 +
''NTP server 1'' and ''NTP Server 2'' let the user select which NTP server (s) will be used to re-synchronize time.<br><br>
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/14838...89611"