Difference between revisions of "Template:FMC640 Dual SIM"

From Wiki Knowledge Base | Teltonika GPS
(Created page with "==Introduction to Dual SIM Functionality== {{{model|FMB640}}} is able to operate in DUAL SIM switching mode to minimize the bill accounts for GSM/GPRS services. SIM1 card has...")
 
 
Line 4: Line 4:
  
 
SIM1 card has higher priority than SIM2. For one SIM
 
SIM1 card has higher priority than SIM2. For one SIM
card using it must be placed in SIM1 slot for FMB640 to switch minimum times. (SIM1 SLOT is closer to PCB, SIM2 SLOT
+
card using it must be placed in SIM1 slot for {{{model|FMB640}}} to switch minimum times. (SIM1 SLOT is closer to PCB, SIM2 SLOT
 
is the upper one).
 
is the upper one).
If SIM card is inserted into SIM 2 slot and 1 SIM operator list mode is used, FMB640 will
+
If SIM card is inserted into SIM 2 slot and 1 SIM operator list mode is used, {{{model|FMB640}}} will
 
work normally, but there will be more switching activities. In addition, APN settings in GPRS
 
work normally, but there will be more switching activities. In addition, APN settings in GPRS
 
should be entered for SIM 1 and SIM 2 to avoid not sending records over GPRS.
 
should be entered for SIM 1 and SIM 2 to avoid not sending records over GPRS.
Line 29: Line 29:
 
inserted in Home profile’s list. At first, it tries to connect to SIM 1 Home Operator, if operator is
 
inserted in Home profile’s list. At first, it tries to connect to SIM 1 Home Operator, if operator is
 
unreachable; the device switches to SIM 2 slot and tries to connect to SIM 2 Home Operator.
 
unreachable; the device switches to SIM 2 slot and tries to connect to SIM 2 Home Operator.
When the connection procedure is successful, FMB640 stays connected to the available
+
When the connection procedure is successful, {{{model|FMB640}}} stays connected to the available
 
Home operator using the SIM card, which was inserted for and works according to the Home
 
Home operator using the SIM card, which was inserted for and works according to the Home
 
profile parameter settings.
 
profile parameter settings.
If none of the Home operators could be connected with, FMB640 switches to the SIM 1
+
If none of the Home operators could be connected with, {{{model|FMB640}}} switches to the SIM 1
 
card tries to connect to its roaming operators from SIM 1 Roaming profile.
 
card tries to connect to its roaming operators from SIM 1 Roaming profile.

Latest revision as of 07:37, 8 May 2020

Introduction to Dual SIM Functionality

FMB640 is able to operate in DUAL SIM switching mode to minimize the bill accounts for GSM/GPRS services.

SIM1 card has higher priority than SIM2. For one SIM card using it must be placed in SIM1 slot for FMB640 to switch minimum times. (SIM1 SLOT is closer to PCB, SIM2 SLOT is the upper one). If SIM card is inserted into SIM 2 slot and 1 SIM operator list mode is used, FMB640 will work normally, but there will be more switching activities. In addition, APN settings in GPRS should be entered for SIM 1 and SIM 2 to avoid not sending records over GPRS.

SIM 1 and SIM 2 APN settings are set in the GPRS tab (Figure). Information about APN and authentication type should be provided by your GSM operator.

Dual.png


  • Dual SIM algorithm

Two SIM cards use algorithm is shown in the diagram below :

Algo.png


  • Home Network

FMB640 gets possible operator codes list from the network and compares them with the operator codes inserted in Home profile’s list. At first, it tries to connect to SIM 1 Home Operator, if operator is unreachable; the device switches to SIM 2 slot and tries to connect to SIM 2 Home Operator. When the connection procedure is successful, FMB640 stays connected to the available Home operator using the SIM card, which was inserted for and works according to the Home profile parameter settings. If none of the Home operators could be connected with, FMB640 switches to the SIM 1 card tries to connect to its roaming operators from SIM 1 Roaming profile.