Changes

Template:FMC640 Features settings (view source)

Revision as of 17:41, 17 August 2023

3,261 bytes added ,  17:41, 17 August 2023
m
no edit summary
Line 37: Line 37:  
     </tr>
 
     </tr>
 
</table>
 
</table>
−
{{{pic_accelerometerposition|[[Image:FMB640accelerometerposition.png|300px|right]]}}} [[FMC640]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.
      +
{{#switch: {{{model|}}}
 +
  | FMC640 = {{{pic_accelerometerposition|[[Image:fmx6_axis.jpg|300px|right]]}}} [[{{{model|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.
 +
 +
 +
  | FMM640 = {{{pic_accelerometerposition|[[Image:fmx6_axis.jpg|300px|right]]}}} [[{{{model|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.
 +
 +
 +
  | FMC650 = {{{pic_accelerometerposition|[[Image:fmx6_axis.jpg|300px|right]]}}} [[{{{model|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.
 +
 +
 +
  | FMM650 = {{{pic_accelerometerposition|[[Image:fmx6_axis.jpg|300px|right]]}}} [[{{{model|FMM}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.
 +
 +
 +
  | #default = {{{pic_accelerometerposition|[[Image:FMB640accelerometerposition.png|300px|right]]}}} [[{{{model|FMC}}}]] Device accelerometer position. (With positive Z axis pointing to Ground and antennas face forward in the vehicle). Before operation with the vehicle on level ground user must send “setacc” SMS.
 +
 +
}}
 
===Auto calibration===
 
===Auto calibration===
 
----
 
----
Line 44: Line 59:  
# The vehicle is stopped.
 
# The vehicle is stopped.
 
# There is a straight road ahead.
 
# There is a straight road ahead.
−
# Send SMS ''"auto_calibrate:set"'' to the {{{model_2|FMB}}} device.
+
# Send SMS ''"auto_calibrate:set"'' to the {{{model|FMB}}} device.
 
# Accelerate to >30 km/h for 5 sec.
 
# Accelerate to >30 km/h for 5 sec.
−
# {{{model_2|FMB}}} will send a response when calibration is completed successfully.
+
# {{{model|FMB}}} will send a response when calibration is completed successfully.
 
Calibration is saved to internal flash memory, which means it will stay after a reset.
 
Calibration is saved to internal flash memory, which means it will stay after a reset.
−
To check auto-calibration status send a following short text message to the {{{model_2|FMB}}} device: ''"auto_calibrate:get"''.
+
To check auto-calibration status send a following short text message to the {{{model|FMB}}} device: ''"auto_calibrate:get"''.
    
==Over Speeding==
 
==Over Speeding==
Line 72: Line 87:  
The scenario is activated and digital output is ON when a call is received from a number which is in authorized numbers list.
 
The scenario is activated and digital output is ON when a call is received from a number which is in authorized numbers list.
 
Call control functionality: <br/>
 
Call control functionality: <br/>
−
* When FMB64 is configured to control DOUT1/DOUT2/DOUT3/DOUT4 device waits for an incoming call from the configured secure number. If the call is received FMB64 turns on DOUT1/DOUT2/ DOUT3/DOUT4 for user-defined Duration timeout (s). If the Duration timeout set to „0“(s), DOUT1/DOUT2/ DOUT3/DOUT4 will be OFF. <br/>
+
* When {{{model|FMB}}} is configured to control DOUT1/DOUT2/DOUT3/DOUT4 device waits for an incoming call from the configured secure number. If the call is received {{{model|FMB}}} turns on DOUT1/DOUT2/ DOUT3/DOUT4 for user-defined Duration timeout (s). If the Duration timeout set to „0“(s), DOUT1/DOUT2/ DOUT3/DOUT4 will be OFF. <br/>
 
* DOUT1/ DOUT2/DOUT3/DOUT4 can be turned off by Duration timeout (s) or by digital input 1, digital input 2, digital input 3, or digital input 4 (DOUT deactivation settings). <br/>
 
* DOUT1/ DOUT2/DOUT3/DOUT4 can be turned off by Duration timeout (s) or by digital input 1, digital input 2, digital input 3, or digital input 4 (DOUT deactivation settings). <br/>
 
* DOUT1/DOUT2/DOUT3/DOUT4 can be turned off before Duration timeout (s) by selected DIN (DOUT deactivation settings).<br/>
 
* DOUT1/DOUT2/DOUT3/DOUT4 can be turned off before Duration timeout (s) by selected DIN (DOUT deactivation settings).<br/>
Line 122: Line 137:  
==Short burst data settings==
 
==Short burst data settings==
   −
{{{short_burst|[[Image:Short_burst.JPG|300px|right]]}}}
     −
[[FMC640]] supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.  
+
{{{model|}}} supports Iridium devices which can send short burst data (SBD) to the server. This means that some data can be sent from FM device to the server through satellites.  
 +
 
 +
In order to properly connect the Iridium device to {{{device|}}}, Iridium has to be connected to the device via RS-232 - COM1 or COM2 (with RJ-45 connector, where 4 pin is GND, 5 pin is RS232 Rx and 6 PIN is RS232 Tx). Additionally '''Pin No. 6''' - power control (reference in the image below) must be connected to one of the {{{model|}}} DOUTs (1/2/3/4), in order to allow the device to power ON/OFF Iridium device on demand. More information about SBD can be found here '''[[{{{model|}}} _Short_Burst_Data|Short Burst Data]]'''.
 +
 
 +
Iridium Edge pinout and RS232 COM 1/2 connection:
 +
 
 +
[[File:Iridium Edge pinout.png|left]]
 +
[[File:FMX640 and RS232 illustration v1.2.png|right|450x201px]]
 +
<br></br><br></br><br></br><br></br><br></br><br></br>
 +
[[File:SBD settings.gif|right]]
 +
When the Iridium edge device is connected '''''Power control DOUT''''' configures DOUT pin which can control Iridium Edge ON/OFF pin. Configure if DOUT pin is connected. Respective power control DOUT to which the Iridium device's ''PIN6'' is connected must be selected.
 +
 
   −
[[FMC640]] will enable satellite mode only if a device can not send data via GPRS. Satellite mode has his own Save/Send period. If timeout is set to 0 no periodic records will be made. It is not recommended to save records often because of satellite traffic prices. 8 kilobytes monthly data limit is hardcoded in firmware. If the data limit is reached – the data limit counter will reset automatically only on next month first day or you can rest counter by SMS command ''“sbdlimitsreset”''.
+
'''''Save/Send period''''' configures how long will {{{model|FMB}}} device wait after losing the signal to generate SBD packet. If the signal is not recovered, it will send it indefinitely (or till the SBD Upload limit is reached, if such is set).
   −
In addition, you can select which IO element can generate Satellite records. In order to do that you need to go to I/O tab select IO record priority Panic and check the checkbox “Satellite I/O” what you want to get that data through satellites if there is no GSM connection.
+
'''''SBD Upload Limit''''' is configurable and resets every month. This option can ensure that no additional data is used so that no unexpected costs are experienced by the customer. The default value is 8000 (for 8KB plan). This option can be disabled by setting the Upload limit to 0. The monthly data usage counter can be reset by using the SMS/GPRS command - '''sbdlimitsreset'''.
−
Record which will be sent through the Iridium satellite network will be different than the regular record. It will contain 4 bytes timestamp, 3 bytes longitude, 3 bytes latitude, 1 byte record generation info, 1 byte DIN, DOUT info, 1 byte speed value.
     −
{{{pic_connection|[[Image:connection.JPG|300px|center]]}}}
+
'''''SBD IO source''''' configures IO source which can trigger SBD record saving.  9 elements can generate an Alarm for SDB sending. These elements are:
 +
* Digital input 1
 +
* Digital input 2
 +
* Digital input 3
 +
* Digital input 4
 +
* Digital output 1
 +
* Digital output 2
 +
* Digital output 3
 +
* Digital output 4
 +
* Speed
 +
<br></br>
 +
Configurator parameter IDs and their explanation:
 +
{| class="nd-othertables_2" style="width:100%;"
 +
|- style="font-weight:bold; text-align:center;"
 +
! '''Parameter ID'''<br />
 +
! '''Parameter name'''
 +
! colspan="3" | '''Values'''
 +
! '''Explanation'''
 +
|- style="font-weight:bold; text-align:center;"
 +
| style="font-weight:normal;" |
 +
| style="font-weight:normal;" |
 +
| '''Min'''
 +
| '''Max'''
 +
| '''Default'''
 +
| style="font-weight:normal;" |
 +
|-
 +
| 99420
 +
| Iridium Edge
 +
| 0
 +
| 1
 +
| 0
 +
| This parameter enables or disables Iridium Edge functionality
 +
|-
 +
| 99421
 +
| Save/Send period
 +
| 0
 +
| 1440
 +
| 1440
 +
| This parameter lets to configure Iridium Edge sending period
 +
|-
 +
| 99422
 +
| SBD IO source'''*'''
 +
| 0
 +
| 8
 +
| 0
 +
| SBD IO elements which when enabled are included into the SBD record
 +
|-
 +
| 99423
 +
| SBD UploadLimit
 +
| 0
 +
| 30000
 +
| 8000
 +
| Limit to save user from exceeding the monthly plan. Max limit of 30000 due to 30KB plan. If set to 0 – limit will be off.
 +
|-
 +
| 99424
 +
| Power control DOUT
 +
| 1
 +
| 5
 +
| 0
 +
| Device DOUT which can control ON/OFF pin of the Iridium Edge
 +
|-
 +
| 151
 +
| RS232 Mode
 +
| 0
 +
| 23
 +
| 0
 +
| RS-232 mode selection. "Satellite backup" - 15
 +
|}
   −
'''NOTE''': Port1/2 cable from FM package can be used for [[TSM232]] connection. For this you need to cut a D-SUB connector and connect wires according to the instruction above (PIN 4 to TSM GND, PIN5 to TSM Rx, PIN6 to TSM Tx).
+
<br></br>
 +
'''*''' SBD IO source parameter is configured with bitmasks:  
 +
*Disabled    = 0x00,
 +
*Din1        = 0x01,
 +
*Din2        = 0x02,
 +
*Din3        = 0x04,
 +
*Din4        = 0x08,
 +
*Dout1          = 0x10,
 +
*Dout2          = 0x20,
 +
*Dout3          = 0x40,
 +
*Dout4          = 0x80,
 +
*Speed        = 0x100
 +
<br></br>
 +
For example: to enable Din1, Din3 and Dout4: 0x01 + 0x04 + 0x80 = 0x85 convert to decimal --> 133.
   −
{{{pic_connector|[[Image:connector.JPG|600px|center]]}}}
+
More information about SBD can be found here '''[[{{{model|}}} _Short_Burst_Data|Short Burst Data]]'''.
   −
'''NOTE''': SBD data is limited to 8000 Bytes per month. For firmware with a bigger SBD data limit, please ask your sales manager.
  −
If the data limit is reached you can reset it with SMS command ''“sbdlimitsreset”''.
   
==Impulse Counters Settings==
 
==Impulse Counters Settings==
  
Retrieved from "https://wiki.teltonika-gps.com/view/Special:MobileDiff/76088...88235"

Navigation menu