Changes

Line 164: Line 164:  
==Configuration==
 
==Configuration==
   −
Make sure the {{{model|}}} device is configured to receive data from “Transcan2 Reefer”, "Touchprint Reefer" or "DataCold Reefer". To do this, enter the configurator window, select the RS232 \ RS485 section displayed in the screenshots below, and configure accordingly (COM1/COM2 Settings, Mode “Transcan2 Reefer”, "Touchprint Reefer" or "DataCold Reefer", Baudrate: Default)
+
Make sure the {{{model|}}} device is configured to receive data from “Transcan2 Reefer”, "Touchprint Reefer", "Euroscan: or "DataCold Reefer". To do this, enter the configurator window, select the RS232 \ RS485 section displayed in the screenshots below, and configure accordingly (COM1/COM2 Settings, Mode “Transcan2 Reefer”, "Touchprint Reefer", "Euroscan"or "DataCold Reefer", Baudrate: Default)
 
  −
[[File:Transcan2_Reefer_2021_08_12.png|alt=|frameless|746x746px]][[File:Touchprint_Reefer_2021_08_12.png|alt=|frameless|746x746px]]
  −
 
  −
[[File:DataCold Reefer 2021 08 20.png|frameless|739x739px]]
      +
[[File:RS-232 refer.png]]
 
==== DataCold Reefer ====
 
==== DataCold Reefer ====
      
To configure "DataCold Reefer" I/O parameters, please select "Reefer IO":
 
To configure "DataCold Reefer" I/O parameters, please select "Reefer IO":
 
+
[[File:ReeferIO.png]]
[[File:Reefer IO settings.png|frameless|1000x1000px]]
      
Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to '''[[{{{model|}}} Teltonika Data Sending Parameters ID#Freezer_IO|Data Sending Parameters page]].'''
 
Data sending parameters (AVL ID) used for "DataCold Reefer" are these: 10040 - 10649. For more in-depth information, please refer to '''[[{{{model|}}} Teltonika Data Sending Parameters ID#Freezer_IO|Data Sending Parameters page]].'''
Line 181: Line 176:  
==== Transcan2 Reefer ====
 
==== Transcan2 Reefer ====
 
To configure "Transcan2 Reefer" I/O parameters, please select "TK Transcom IO":
 
To configure "Transcan2 Reefer" I/O parameters, please select "TK Transcom IO":
 +
[[File:TranscanIO.png]]
 +
Data sending parameters (AVL ID) used for "Transcan2
 +
" are these: 10683 - 10694. For more in-depth information, please refer to '''[[{{{model|}}} Teltonika Data Sending Parameters ID#Freezer_IO|Data Sending Parameters page]].'''
   −
[[File:Transcom IO settings.png|frameless|1000x1000px]]
+
==== Euroscan IO====
 +
To configure "Euroscan refeer" I/O parameters select "Euroscan IO":
 +
[[File:EuroScanIO.png]]
   −
Data sending parameters (AVL ID) used for "Transcan2 Reefer" are these: 10683 - 10694. For more in-depth information, please refer to '''[[{{{model|}}} Teltonika Data Sending Parameters ID#Freezer_IO|Data Sending Parameters page]].'''  
+
Data sending parameters (AVL ID) used for "Euroscan" are these: x- X. For more in-depth information, please refer to '''[[{{{model|}}} Teltonika Data Sending Parameters ID#Freezer_IO|Data Sending Parameters page]].'''
   −
==== Touchprint Reefer ====
+
==== TK Touchprint/Touchlog I/O ====
 
To configure "Touchprint Reefer" I/O parameters select "TK Touchprint IO":
 
To configure "Touchprint Reefer" I/O parameters select "TK Touchprint IO":
   −
[[File:Touchprint Reefer IO settings.png|frameless|1000x1000px]]
+
[[File:TouchprintIO.png]]
 
   
Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to '''[[{{{model|}}} Teltonika Data Sending Parameters ID#Freezer_IO|Data Sending Parameters page]].'''
 
Data sending parameters (AVL ID) used for "Touchprint Reefer" are these: 10695 - 10703. For more in-depth information, please refer to '''[[{{{model|}}} Teltonika Data Sending Parameters ID#Freezer_IO|Data Sending Parameters page]].'''
  −
         
[[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.
 
[[Codec#Codec_8_Extended |Codec 8 Extended]] should be selected as the main data protocol in the “Protocol Settings” tab, which is located in the “System” section.
   −
[[image:Reefer3.png|center]]
   
[[Category:{{{model|}}}]]
 
[[Category:{{{model|}}}]]
 
[[Category:{{{model|}}} Manual]]
 
[[Category:{{{model|}}} Manual]]