EYE BEACON / BTSID1

From Wiki Knowledge Base | Teltonika GPS
Main Page > Sensors > EYE BEACON / BTSID1

Introduction

Wireless solutions open up new horizons for your business and help to keep an eye on your assets. Discover our brand-new and certified Bluetooth Low Energy ID beacon model from Teltonika with robust waterproof casing and a long-lifetime battery. The model designed for a low-cost fast and easy configuration and integration to save precious time, resources, and ensure accountability.

EYE device.png

About BTSID1

Perfect for traceability use cases, delivery tracking, monitoring of various movable objects in logistics (trailers, containers), agriculture (tractor attachments), and constructions (tools and inventory). Also, it suitable for indoor tracking solutions for items tracking in warehouses, hospitals, transport hubs and other types of industrial areas. EYE beacon supports iBeacon and Eddystone protocols. The device is fully compatible with the Teltonika firmware platform which provides extended functionality. Configure, scan, and update anytime anywhere with a dedicated Teltonika mobile app.

Product Specification

Features

Functionalities
Beacon ID, LED
Dimensions and weight
Dimensions 56,6 mm x 38 mm x 13 mm
Weight 19 g 18g
Battery and power (not confirmed)
Model CR2450
Type Type Lithium, Manganese Dioxide
Total Capacity 620 mAh
Replaceable No
Battery life (Tx=2 dBm; interval: 3 s) 5+ years

(Tx=2 dBm; interval: 3 s)

Battery life (Tx=2 dBm; interval: 10 s) 10+ years

(Tx=2 dBm; interval: 10s)

Electronic
Microcontroller ST Microelectronics BlueNRG-2
Connectivity
Bluetooth Bluetooth 4.2 compliant,

Bluetooth 5.2 certified

Range 80 m
Available transmission power levels Up to 8 dBm
Sensitivity -88 dBm
Casing
Protection IP67
Mounting Two holes to screw/leash/strip, tape
Customization Custom logo upon request (Special conditions)
Environmental Requirements
Operational temperature -20 °C / +60 °C (-4 °F / +140 °F)
Protocols compatibility
iBeacon Yes

*iOS doesn't show devices with iBeacon protocol

Eddystone Yes
Certificates
CE (EU) Yes
FCC (USA) Yes
UKCA (UK) Yes
RoHS Yes
E-mark Yes

Dimensions

Eye dimensions.png

Mounting recomendations

Mounting recomendations.jpg
Mounting recomendations 1.jpg

Configuration

Devices work constantly and are ready to perform out of the box. Default basic Sensor settings are set to:
• Transmitting at 2 dBm power.
• Data advertising at 3 second intervals.
• Eddystone protocol

If you would like to change these settings you will need to:
1) Download and install EYE APP - Teltonika application to change sensor settings.
QR.jpg

Eye app

With the application you will be able to scan for visible Teltonika EYE devices, check their statuses or connect for configuration or firmware update.

Detailed list - collapsed(2).jpg
Overview - without update (beacon)(2).png
Basic settings(2).png
Advance settings 4.png


Devices in view: In this window you will see all visible devices. You have options to see devices in Short list Shortlist.jpg or in default list. When looking at devices in default list you will be able to open Detailed view Detailed.jpg of devices and check transmitted data statuses. Additionaly if you are looking for specific devices you will be able to use Search Search button eye app.jpg function to filter search options. When in this window select a device of your choice to connect and after passing pin code you will go to device overview window.

Overview window: In overview window you can see device details, check firmware version and update if available , go to device configuration settings. If you select to Configure device new window will open with Basic and Advanced settings.

Configure window: In this window you can check and change device configuration settings. In main tab Basic Settings you can change main settings. Change Device name, Power signal strength, Advertising interval and Packet transmition type*. For more settings go to Advanced settings tab to enable various events.

Advanced configuration window: Beacon information (iBeacon ID*, Eddystone ID). UUID/MINOR/MAJOR parameter can be changed for iBeacon ID*. Namespace ID/Instance ID can be changed for Eddystone ID

IBeacon ID settings.png

Eddystone ID settings.png

*iOS doesn't show devices with iBeacon protocol

Teltonika configurator without EYE functionality

If you have firmware / configurator which does not support EYE Beacon tab in Bluetooth 4.0 section, then you can use Beacon list section of the configurator to scan available EYE Beacons.
Below are short instructions which show how we recommend configuring the device to Enable the Beacon functionality for testing.

Steps to follow according to the visual representation

  1. In System Settings Enable Codec8 Extended;
  2. In Bluetooth settings Enable Bluetooth, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth will be disabled;
  3. In Bluetooth 4.0 settings, set Non Stop Scan to "Disable", configure "Update Frequency" and "Scan duration" as 30 seconds. These settings will bring the best results for BLE scanning with our device;
  4. In Beacon list settings, configure Beacon Detection as "All" and Beacon Record as "Eventual". This will detect all surrounding Beacons and create Beacon records every 30 seconds.

Beacon project V3.gif


Teltonika configurator with EYE functionality

Bluetooth 4.0
Functionalities were reorganized and transferred to Bluetooth 4.0 configuration tab with additional horizontal tabs selection for specific settings:

  • Global - Parameters responsible for device scanning ability like power and duratations.
  • Beacon - Parameters to enable Beacon scanning scenarios.


Common settings

  • Non Stop Scan - Enable Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
  • Sensors and Beacons Update frequency - changes sensors temperature/humidity/battery voltage data update frequency. Minimum value: 30s, maximum value: 65535s. Recommended value 30.
  • BLE Scan Duration - Sensors data reading time. Recommended value 30.
  • Scan retries until error - Scan retries count, till start to show the value as Error '3000' - sensor disconnected. Recommended value 30.
  • BT Power Level - Telematics device Bluetooth power level setting.
  • BLE Broadcasting service ID - Telematics device can broadcast configured ID.
  • BLE connection control - Connection mode settings. If broadcasting ID is configured, parameter should be set to Prohibit.


Configurator GUI changes.png

Beacons
Beacons configuration instruction: How to start with FMB devices and Beacons?

EYE Beacons configurator.png

Beacon detection - Parameter controls over all Beacons scanning:

Beacon detection configurator.png
  • Disabled – Beacon scanning and transmitting disabled.
  • All – Read all visible beacons;
  • Configured – Read only beacons set in Beacon List;
  • Teltonika MAC – Filter and transmit only Teltonika EYE packets*.
    *It allows to filter only MAC addresses which will be assigned to BTSX device. The MAC address that is currently filtered by this parameter is FD:5F:9A:XX:XX:XX.



Beacon record

Beacon record on change.png

Eventual settings have two modes:

  • Monitoring - Beacon record generating every scan period
  • On change - Beacon records are generated only when there are changes in scanned list.

Periodic - records are generated according to Period settings. When there is no visible beacons, empty record will be generated.

Beacon Mode

Beacon Mode SImple.png
  • Simple - beacon parsing is done automatically (Eddystone and iBeacon protocols are supported).
  • Advanced - beacon data capturing can be configured.



Filter type

Filter Type.png

New firmware has two Beacon lists, so it is possible to create two separate lists of beacons, standard one with Beacons ID (UUID:Major:Minor, or Namespace:InstanceID) and new one according Beacon Name (by name or prefix, for example all beacons with prefix "ID1" can be saved.

  • Beacon ID - configurator allows to configure beacon id in iBeacon or Eddystone format.
  • Beacon Name - user can enter names of beacons which needs to be filtered. It would filter the full name or only if the prefix of the name is configured like “BTS”.


Both ID and Name filters can work at the same time. If beacon doesn’t match ID filter, but matches the name, it will be added to beacon list. Filtering only works Beacon Mode is set to Simple.

Proximity

Proximity.png


Proximity Events allow to configure 3 different zones: Near, Away, Far Away. There is additional Lost parameter for beacons which were lost from any of the 3 zones. Averaging timeout determines period how often results are evaluated to avoid fake event detection. Periodic option will generate records at known interval while On Change option will generate record when beacon enters/exits certain zone.

Proximity IO elements have the following structure 1st beacon protocol version.png

Protocol overwiev

Beacon advertising


Beacon advertising.png


Protocol parsing example

AVL Data Packet
AVL Data Packet Part HEX Code Part
Zero Bytes 00 00 00 00
Data Field Length 00 00 00 40
Codec ID 8E (Codec8 Extended)
Number of Data 1 (Number of Total Records) 01
AVL Data Timestamp 00 00 01 70 1F 9B 3F A9 (GMT: Friday, 07 February 2020 12:23:53.001)
Priority 01
Longitude 0F 0E 50 2A
Latitude 20 9A B4 61
Altitude 00 74
Angle 00 C6
Satellites 0E
Speed 00 00
Event IO ID 01 81 (385)
N of Total ID 00 01
N1 of One Byte IO 00 00
N2 of Two Bytes IO 00 00
N4 of Four Bytes IO 00 00
N8 of Eight Bytes IO 00 00
NX of X Bytes IO 00 01
N’th IO ID - AVL ID. 01 81 (385)
Length of Variable Length IO 00 13
Value of Variable Length IO 1101E39B606AA38255AA8E460B154E2D0055CF
Number of Data 2 (Number of Total Records) 01
CRC-16 00 00 00 56

Safety information

This message contains information on how to operate BTSID1 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

1. To avoid mechanical damage, it is advised to transport the device in an impact-proof package.

2. In case of malfunction contact yours Teltonika account manager or write to technical support team over VIP helpdesk.
Safety.jpg

External Links

https://teltonika-gps.com/eye/