Teltonika DualCam

From Wiki Knowledge Base | Teltonika GPS
Main Page > Video Solutions > Teltonika DualCam

Introduction to the product

Teltonika DualCam is connected to FMX125 and FMU126 devices using the RS232 interface.

DualCam1.png

How to insert microSD cards

Teltonika DualCam can hold 2 x microSD cards, which are inserted on both sides of the camera (front and rear).
When the card is inserted correctly, it locks in with a "click". How the cards are inserted is depicted in the photos.

Dual camera MicroSD card insert 1.png Dual camera MicroSD card insert 2.png

Product Specification


Technical data Description
Supported by FMC125, FMM125, FMU125, FMU126, FMB125
Day & Night Vision Effect Day (Color), Night (Black & White)
Angle of View Horizontal 120°, Vertical 70°
Dual Camera Front and Rear (equal characteristics)
Camera casing dimensions 126.2 x 36.6 x 36.6 mm
Camera mounting Sticky tape (3M) or screws
Supported microSD card sizes 16 GB, 32 GB, 64 GB


Electrical parameters Description
Input voltage range 9 ~ 36 V
Working temperature and humidity Temperature: -30 °C ~ 85 °C

Humidity: <90%

Power consumption 220 mA


Function parameters Description
Real time clock (RTC) synchronization Available over FM (via NTP, NITZ or GNSS)
Picture resolution 1280 x 720 (default) (50KB transfer period 18 sec), Configurable: 160 x 120; 320 x 240; 640 x 480; 1920 x 1080
IR Distance 2 Meters
Cable length RS232 (3.5 m)
Video compression H.265
Video resolution 720P (20 sec. – 6MB, transfer period ~ 320 sec.)
Video storage 2psc. MicroSD card (Max 64GB up to 72 hours of video)


DualCam Firmware Version

We are always improving our device's performance, stability, and reliability.
This document describes DualCAM platform devices' firmware improvements, changes, new features implementations as well as current firmware release version.


FIRMWARE VERSION RELEASE DATE CHANGES
03.27.07.Rev.361
2021-09-17
  • Minor improvements
03.27.07.Rev.360
2021-08-30
  • Extended video and image sending configuration
  • Added Domain and Port parameters to “camreq” command
  • Extended “camreq” response
  • Added “camgetver” command
  • Fixed timestamp for video meta data
  • Improved system stability and fixed general bugs
03.27.03.Rev.104
2021-06-18
  • Added image sending trigger
  • Ability to configure multiple video triggers
  • Always enabled DualCam scenario support
  • Improved system stability and fixed general bugs
03.27.00.Rev.100
2021-02-19
  • Initial release


DUALCAM FIRMWARE VERSION RELEASE DATE CHANGES
V1.9.3
2021-07-15
  • Improved stability and fixes of camera data packets
V1.9.2
2021-06-02
  • Fixed issue with front camera crash if picture size is too large
  • Added command to check the camera version
  • Improved system stability and fixed general bugs
V1.9.0
2021- 02-19
  • Initial release

Certifications & Approvals

Installation

To connect the DualCam to a supported device, you have to make sure to connect 4 PINs of the camera to the PINs of your device correctly. Dual camera scheme 1.3 (1).jpg

PIN NUMBER PIN NAME

DESCRIPTION

1 RS232-Tx DualCam output for data transmission through RS232
2 RS232-Rx DualCam input for data reception through RS232
3 VCC(9-36V) (+) Power supply for the DualCam
4 GND (-) Ground


DualCam RS232 camera support

DualCam camera support was introduced from firmware version 03.27.06.Rev.360. A new RS232 mode "DualCam" was added with parameters for setting control. The details of the RS232 mode parameter are provided in the table below.

Parameter name Parameter ID Parameter value
RS232 Mode 151 18
size

Configuration version 8.14.1.0 has to be used if configuration is being made in offline mode.



Camera Feature Settings

size

Once this mode is enabled, new tab “Camera Settings” appears on the left sidebar. This will contain the main parameters for configuring the camera settings The parameter IDs and values are provided in the table below. Once configuration is saved to device, these parameters are updated.

Parameter name Parameter ID Parameter values Default values
Camera Picture Resolution 66000
0 - 160 x 120 3
1 - 320 x 240
2 - 640 x 480
3 - 1280 x 720
4 - 1920 x 1080
Camera Picture Compression 66001 [0 - 100] (%) 50
OSD Display 66002 0 - Disabled 0
1 - Enabled
Video Frame Rate 66003 20, 25 and 30 (frames per second) 30

OSD display - On Screen Display feature displays date and time in the upper left corner of the photo. This feature can be enabled or disabled.

Camera Scenario Settings

size

"Camera settings" tab also contains scenario settings that trigger camera video/photo capture when specific condition is met.

Parameter name Parameter ID Parameter values Default values
Periodic Image sending 66006 0 - Disabled 0
1 - Front Camera
2 - Rear Camera
3 - Both Cameras
Sending interval 66007 [10-1800] (seconds) 600
Image Sending Trigger 66022
0 - None 0
2 - DIN1
4 - DIN2
8 - Crash
16 - Towing
32 - Idling
64 - Geofence
128 - Unplug
256 - Green Driving
Video sending trigger 66023
0 - None 0
2 - DIN1
4 - DIN2
8 - Crash
Video duration before trigger 66009 [1-10] (seconds) 5
Video duration after trigger 66010 [1-10] (seconds) 5
Camera Scenario Mode 66020
0 - On Ignition 0
1 - Always
Video source for trigger DIN1 66040
0 - None 0
1 - Front
2 - Rear
3 - Front and Rear
Video source for trigger DIN2 66041
0 - None 0
1 - Front
2 - Rear
3 - Front and Rear
Video source for trigger Crash 66042
0 - None 0
1 - Front
2 - Rear
3 - Front and Rear


Periodic image sending scenario

Periodic image sending triggers photo capture from a front camera, whenever the timeout is reached (sending interval parameter).

Update: Since 03.27.03.Rev.04 firmware, Periodic Image Sending Enable/Disable switch was replaced by a camera selection:

  • Both cameras deselected – periodic image sending is disabled (value 0)
  • Front camera selected – front camera’s pictures will be sent periodically (value 1)
  • Rear camera selected – rear camera’s pictures will be sent periodically (value 2)
  • Both cameras selected – both cameras’ pictures will be sent periodically (value 3)

If the camera has not finished uploading pictures to the server, then the photo capture is skipped.

Camera Scenario Mode

The options On Ignition and Always determine the working mode.

On Ignition means the camera scenarios will operate the way it was up to 03.27.03.Rev.105, that is it will work only when the ignition is detected.

Always mode means the camera scenarios will work all the time, including whenever the device is in sleep mode (excepting Ultra sleep mode during which scenario is disabled). During sleep footage requests (if the network is available), periodic image sending and triggers work as well.

Warning: using Always mode, depending on the configuration, the device might wake up from sleep very frequently. That has to be taken into consideration when configuring the scenarios.

Video sending by trigger

Video sending by trigger camera scenario monitors the selected trigger (video sending trigger parameter) and captures video from front, rear or both cameras before and after the event (video duration before trigger and video duration after trigger parameters). If the previously captured video has not finished downloading, then a new video capture is skipped until the old one has been sent. When this scenario is triggered, high priority eventual record is generated with the value corresponding to what triggered the scenario. See the table below.

Parameter name Parameter AVL ID Parameter value
SOS trigger 499 0 - Server request
1 - DIN1
2 - DIN2
3 - Crash
4 - Towing
5 - Idling
6 - Geofence
7 - Unplug
8 - Green Driving

Image sending trigger

Added Image sending trigger option (works the same way as Video sending trigger just triggers image sending). Both front and rear images will be sent.

For selecting multiple options using SMS/GPRS commands, add values of every option and set that value for this parameter.

For example, to set DIN1 (2), Crash (8), and Unplug (128) scenarios as triggers, add their values (2 + 4 + 128 = 138) and set the sum as the parameter value

Camera firmware version

Additional SMS/GPRS command for cameras’ firmware checking. Since both cameras are separate, there are two versions returned.

Command Arguments Explanation
camgetver None Used to check firmware versions.

Returns version in the format: V<major>.<minor>.<revision>. For example, V1.9.3.

Because there are two cameras, two versions are returned. The complete response would look like this: Front camera V1.9.3. Rear camera V1.9.3.

If there are problems reading the version or if the camera is not responding/connected, the return would be this: The front camera camgetver failed. The rear camera camgetver failed.

Camera request command

A new camera request has been added, which allows the server to request files from a camera. The format is as provided below in the table:

Command Arguments Explanation
camreq: <file_type>,<file_source>,<timestamp>,<duration>

,<domain>,<port>

Captures appropriate file with the provided details. If the connection to server is opened, them files immediately become available for download. If not, then connection is tried to be made. If <domain> and <port> parameters are included, the device will send footage of the command to that address.

The arguments are as follows:

  • <file_type>
    • 0 - Video
    • 1 - Photo
  • <file_source>
    • 1 - Front camera
    • 2 - Rear camera
    • 3 - Both cameras
  • <timestamp>
    • Unix timestamps in decimal (not required for photo download)
  • <duration>
    • Video duration in seconds from provided timestamps (not required for photo download), (max 30 sec)

Structure examples:

camreq:<file type>,<file source>(if video, add ",<timestamp>,<duration>)

However, if there is a need to send to the specific server without configuring, you can add two extra parameters. The complete structure:

camreq:<file type>,<file source>(if video, add ",<timestamp>,<duration>),<domain>,port

For example: camreq:0,1,1624960616,5,212.59.13.226,7160


Conditions Command response
Request successful and server connection successful. Device is ready to send selected file Photo request from source <1-3>.

(If photo request)


Video request from source <1-3> for <1-255> seconds since YYYY-MM-DD HH:MM:SS.

(If video request)

Preparing to send file from timestamp <timestamp of the file>
Request successful but the device was already connected to the server. Device is ready to send selected file Already connected. Preparing to send file from timestamp <timestamp of the file>
Request received but the capture failed Error: capture failed
Request received but the device cannot proceed with the capture and sending because ignition is off Error: Cannot capture because ignition is off
Request received but the previously captured and prepared photo/video was not sent. New media is not captured. The device is ready to send the previous capture Warning: Photo / Video already captured previously, trying to send it
Request received but the device was already connected to the server. New media is not captured. The device is ready to send previous capture Already connected. Warning: Photo / Video already captured previously, trying to send it
Request received but the camera doesn’t acknowledge sent command. Nothing will be sent Error: DualCam NAK
Request received but the camera is not connected or not working Error: DualCam not present
Request received but the camera is not connected or not working Error: requested file does not exist
Request received but the device cannot connect to the server Error: connect to server
Request received but the modem is not ready for operation (network or modem issue) Error: modem not ready to start send
Request received but the device cannot proceed with the capture and sending because the camera is being reconfigured Cannot send, DualCam configuration is in progress
Request received but file capture time was exceeded. Error: Media request timeout
Request received but capture completed incorrectly Error: Media request problem
File type parameter incorrect in the request command Error: Invalid File Type argument in camera request cmd!
File Source parameter incorrect in the request command File Source
Timestamp parameter incorrect in the request command Timestamp
Duration parameter incorrect in the request command Duration
Cannot proceed with the request, ignition is off Error: Ignition not detected!
Request command structure incorrect Error: Invalid camera request command!
RS232 and DualCam mode is not enabled Error: DualCam is not configured!
Front or rear camera not found Error: Front / Rear Camera not present


Camera ping transmission and TF status checking

Camera pinging was implemented to periodically check if a camera is connected to a device. This is done via “Get TF status” command for both front and rear camera every 20 seconds when ignition is on. The received result from this command is stored in two corresponding AVL elements “Front camera state” and “Rear camera state”. The following do not only store TF status, but also if response from the camera was received or not.

Parameter name Parameter AVL ID Parameter values
Front camera state: 498 0 - Camera not detected
1 - No card
Rear camera state: 497
2 - Card mount failed
3 - Card mounted
4 - Card faulty


Camera RTC synchronization

Camera RTC synchronization is done anytime the device itself is synchronized (via NTP, NITZ or GNSS).

How to read camera data from SD card

The software for reading camera data can be downloaded here

Data reading steps:

  1. Double-click “VideoPlayer.exe” to open the player
  2. When the software starts, first select the directory where the TF card files are located. Once located, click "OK". The software starts analyzing the pictures and videos existing in the TF card files.
  3. Software will automatically detect the video and picture in the TF card files, which will last for a few seconds and then enter the software, as shown.,

The upper part of the software is a calendar. You can choose to view whether there is a video in the current month according to the year and month. The number of the year/month can be entered by keyboard after selecting it, and then press the “Enter” key to jump to the entered year/month. You can press Button1.png to view the previous year/month and Button2.png to view the next year/month. The date of the recorded video in the current month will be marked in blue. The lower part of the software is the preview interface, divided into two parts: "Video View" and "Image View".

Video View

Video view shows the video information. Left click on the date of the video in the calendar, then the following "Video View" section will show which time period there is a video, as shown. For video recording, the time period during which the video is recorded will be marked in blue.

Click on the blue part of the timeline to get the time you clicked, and the video thumbnail of the current time will be displayed in the middle of the screen. The timeline length is 24 hours and it is difficult to locate the exact number of seconds. Hold down the timeline with the left mouse button and then swipe to the right to zoom in on the timeline. For example, we need to carefully view the video at 05:00-07:00. Then, the left mouse button is pressed at the 05:00 position and slide to the right to the position of 07:00, so that this part of time can be enlarged to the entire timeline.

Note: If you need to restore, then left-click and hold the time axis to slide left.

Video Playback

Left click on the timeline will view the video thumbnail of the clicked time point, and double click the left mouse button to start playing the video from the current time. By default, the video will be played for two minutes from the selected time. If you click to find the location you want to play, you don't need to move the mouse, double click again will pop up the play form.

Vplayback.png

Video playback interface contains
Stopp.png
Stop button
Speediup.png
Speed up

play button

Pause.png
Pause button
Screenshot.png
Screenshot

button

Slowdown.png
Slow down

play button

Fullscreen.png
Full screen

button

Note: Closing the current playback interface does not exit the player software.

Image view

"Image View" displays the image information (the camera saves the image in the TF card after the person takes the initiative to take the photo, here you can see the photo taken by the camera). We first click on "Image View" to switch the software to the image page.

After switching to the picture interface, you can view when the photo is taken according to the directory. As shown below, after expanding the index, we can see how many pictures in total were taken.

Imageview1.png
Imageview2.png



After the expansion, click the time of the image generation to see the preview on the left side. Clicking on the preview image will pop up the image viewing window. The size of the window is the size of the image itself. The scroll wheel zooms in and out of the picture. You can right click on the preview to save the original image to your hard disk. Imageviwe.png

Export MP4

Click the "Convert" button Convert.png to convert the video in the TF card to MP4 and export it.

Then first select the folder you want to export to, enter the MP4 start time and end time to be exported, and then click Export, if you need, cancel the export. Exporting.png

Then wait for the export to complete. The time of export is not certain. Depending on the performance of the computer, it takes about 1 to 5 minutes for each 1-hour duration video.

Other camera related functionality

Camera is configured if all of these conditions are met:

  1. RS232 mode is selected (DualCam)
  2. Camera was not configured since startup or one of the related parameters were changed (compression, framerate or OSD)
  3. Camera file transfer is not active

Active camera reconfiguration is accompanied by two consecutive camera shutter clicks. If camera is disconnected and later reconnected, a device will detect it by periodic camera ping packet. Once camera is detected, the device will reissue the reconfiguration procedure.

Camera file transfer reconnection

If FMU1YX device has bad reception, server is not reachable or wrong server details are configured, then the device tries to open a link to a camera server few consecutive times. If no connection was possible to be established, then the connection is postponed for 30 minutes and tried again (or tried every configured sending interval if periodic image sending is enabled).

DualCam camera file transfer support

size

Once camera has at least one file captured, it starts connection to a remote server, which is configured by parameters “Domain” and “Port” found in the “Camera Settings” tab.

Initialization packet

On connection, a device sends an initialization packet.

Header(0x0000) Protocol ID IMEI Settings
2 bytes 2 bytes 8 bytes 4 bytes

Protocol ID – just a reference for the protocol version that is running on a device (for server cross compatibility with older versions). Firmware FMB.Ver.03.27.00.Rev.100 and up have protocol ID 5. Settings flag contains information on what is available for download. Structure is provided below:

Settings, 4 B
Byte 3 Byte 2 Byte 1 Byte 0
1 2 3 4
  1. Video, rear (%videor)
  2. Video, front (%videof)
  3. Photo, rear (%photor)
  4. Photo, front (%photof)

If identifier sent to a server is not valid, device disconnects.

General command structure

General communication packet structure is as in the table bellow. It consist of CMD_ID (2 bytes), Data length of a command and a payload.

Command ID Data length Data
2 bytes 2 bytes [data length] bytes


Communication protocol

Close a session command (CMD ID 0x0000)
In case when a device connects to a server, but the server does not expect it to connect, the server will respond by sending a CLOSE command after which the connection will be terminated. This command is also used when the device connects to a server for a custom file sending and the server finishes to send all custom files to the device.

Command ID Data length
0x0000 0x0000


Start file transfer command (CMD ID 0x0001)
After device received file request command from the server (0x0008) device sends START command with file data (packet count).

Command ID Data length File Packets (4 bytes) Blank field (2 bytes)
0x0001 0x0006 0x12345678 0x0000 (always same value)


File request command (CMD ID 0x0008)
After the device is connected for a file upload, the server initiates file transfer by sending a FILE REQ command.

Command ID Data length File Identifier
0x0008 2 bytes See the table below

The device should answer with a START command described above indicating the size and CRC of the requested file.

File source, type Identifier (ASCII chars)
Photo from camera, rear %photor
Photo from camera, front %photof
Video from camera, rear %videor
Video from camera, front %videof


Resume file transfer command (CMD ID 0x0002)
In a response to the START command a RESUME command must be sent from server.

Command ID Data length Packet offset (4 bytes)
0x0002 0x0004 0x00000001

To begin file transfer from the start, offset should be set to 1 (4 bytes value). In case when the file transfer was interrupted, to resume file transfer, offset can be set to the desired value (1 ≤ [offset] ≤ [file packets]).

Synchronize file transfer command (CMD ID 0x0003)
In a response to the RESUME command a SYNC command is sent from device.

Command ID Data length File offset (4 bytes)
0x0003 0x0004 0x00000001

By sending the SYNC command it is ensured that the next data command will contain file data starting from the specified offset.

File data transfer command (CMD ID 0x0004)
After sending a SYNC command, a file data transfer is started by sending DATA commands.

Command ID Data length File data (up to 1024 bytes) Data CRC (2 bytes)
0x0004 0x0402 ... ...

A File data is split into 1024 byte parts, each part wrapped into a DATA command and is sent.
Note: if a command with a bad CRC is received, RESUME command should be sent with the last valid file offset, after receiving a RESUME command, the server will stop sending DATA commands and continue communication from “Resume file transfer” step.
CRC polynomial expression: 0x8408 The initial value, when calculating CRC, is the previously received packet (CMD ID 0x0004) CRC value.

File transfer status command (CMD ID 0x0005)
After a file transfer is completed and no more files are required from the device, a server should send a COMPLETED command to the device (this command does not work after executing repeat init command0 x0009 – in this case, the server should send a CLOSE SESSION 0x0000 command mentioned before).

Command ID Data length Status (4 bytes)
0x0005 0x0004 0x00000000

In case of the server using invalid arguments, commands or not following the file request flow, the device will send this command with a Status field set to one of the few possible error codes. A list of possible ones is provided below.

Status value (hexadecimal) Description Notes
0x00000000 File transfer process completed Sent from server
0x00000002 Failed to close GPRS Sent from device
0x00000003 Failed to close socket Sent from device
0x00000005 Invalid response from server to init packet Sent from device
0x00000011 This error code forces the device to disconnect from server Sent from device. Possible causes:
  • Camera is not configured
  • The requested file is not available by camera

After a COMPLETED command device should disconnect from the server.

Initialization packet repeat command (CMD ID 0x0009)
When sent, the initialization packet is repeated. This is used, when all of the files are downloaded and an additional check is carried out for any additional files, that may have been captured during the download operation.

Query file metadata request (CMD ID 0x000A)
This command is used for retrieving extra information about a selected file. A file identifier is used to determine which file’s information will be received. File identifiers are identical and used in the same way as in the File Request Command (0x0008).

Command ID (2 bytes) Data length (2 bytes) File Identifier (7 bytes)
0x000A 0x0007 0xFFFFFFFFFFFFFF

Can be sent after the initialization packet or after the file transfer is complete. It is not a mandatory command and doesn’t have to be used. The response for this command is 0x000B (more details below).

Note: 0x000A command was added since 03.27.04.Rev.104 firmware version and would not work with older versions.

File metadata response (CMD ID 0x000B)
0x000B is a response command to the request command 0x000A.

Response command returns information about a specified file: file type, timestamp, trigger, and video length. Complete command’s structure:

Command ID (2 bytes) Data length (2 bytes) Command version (1 byte) File type (1 byte) Timestamp (8 bytes) Trigger (1 byte) Video length (2 bytes)
0x000B 0x000D 0xFF 0xFF 0xFFFFFFFFFFFFFF 0xFF 0xFFFF

Note: 0x000B command was added since 03.27.04.Rev.104 firmware version and would not work with older versions.

Response command meta data:

Data Description
Command version Iteration of the command itself to determine to parse of the data
File type Media type for confirming which file’s metadata is received. Byte structure is the same as byte 3 in the initialization packet settings data
Timestamp Timestamp at the time of the trigger. Same used in a corresponding SOS record
Trigger Trigger values. Same values as video sending trigger in SOS record.
Video length Duration of the video in seconds. If the file type is a photo, this value is 0x0000.

File transfer visual flow

size

Troubleshoot

DualCam Checks

  • Check RS232 configuration, baud rate, etc. Default values should be set for the DualCam.
  • See if both cameras are working. Try sending separate picture requests and check the result. “camreq:1:1” for the front camera and “camreq:1;2” for the rear camera. Possible responses to "camreq" command - Camera request command

Check camera IO values in the configurator.

  • See if the camera is physically enabled, gets power, and re-check the RS232 connections. You can also test if the camera is physically enabled by covering the light sensor on the rear camera (marked green in the picture below). The rear camera’s IR LEDs should turn on by doing so in a dark environment.

DualCam Reset.png

  • If the camera seems to be enabled, check the SD card content. See if there are any files and review the footage using TF CardVideoPlayer v1.14. If there is some footage from the time the camera was turned on. The actual time in the camera might differ, therefore check older dates to see if there are any videos.
  • If some recent video files were found, it means that the camera is working, but not responding to RS232 commands. Otherwise, the camera is either not working or not responding to commands and does not detect SD card.

Possible solutions

  • Camera might have a problem detecting SD card. Format microSD card using FAT32 file system. Try different cards. Try re-inserting the cards while the camera is turned on. Also, keep in mind that the smallest supported card is 16 GB.
  • Physical camera restart. Disconnect the camera’s power supply and disconnect from the FMX125 device. Leave the camera for a few minutes like that and power it on but do not connect to the FMX125 for a few minutes. After some time, reconnect the device and check if the camera responds.
  • Try firmware update:
    • Upload firmware to both SD cards. The firmware file has to be the exact name “JPEG_IPC_APP” name without any extensions.
    • Disconnect the camera from the FMX125 device.
    • Power the camera off.
    • Put the SD cards in.
    • Turn the power on but do not connect to the FMX125.
    • Wait for 3-5 minutes.
    • Turn off the power and reconnect to the FMX125 device.
    • Power on the camera with the FMX125 device.
    • Check whether Codec8 Extended is enabled. Without Codec8 Extended, parameters of AVL ID 497, 498, 499 WILL not be sent.

Data protocol.gif

If nothing helps and the camera is still not working or working incorrectly, log data using 2;3;9;1 filter and collect the log files.