Line 1: |
Line 1: |
| + | ==Disclaimer== |
| + | |
| + | [[File:Alert.png|left|link=]] <br> If you are not using Bluetooth®, '''please consider turning it off''' or '''change Bluetooth® PIN''' to remove potential risks. |
| + | |
| + | If you are using Bluetooth® we strongly recommend '''using AES encryption''' for enhanced security. |
| + | |
| =Sensors= | | =Sensors= |
| | | |
− | TAT100 has a BLE connectionless devices reading feature that can be configured in the '''Bluetooth''' tab. When '''Sensors''' mode is selected a table with configurable parameters will appear. Currently to the TAT100 device up to '''4 sensors''' can be connected. | + | TAT100 has a BLE connectionless devices reading feature that can be configured in the '''Bluetooth®''' tab. When '''Sensors''' mode is selected a table with configurable parameters will appear. Currently to the TAT100 device up to '''4 sensors''' can be connected. |
| | | |
| [[Image:TAT100_BLE_Sensor_configuration_v3.png|250px|{{{general|size}}}|right]] | | [[Image:TAT100_BLE_Sensor_configuration_v3.png|250px|{{{general|size}}}|right]] |
| <br>'''BLE Feature:'''<br> | | <br>'''BLE Feature:'''<br> |
− | <br><code>None</code> – Bluetooth functionality will be disabled. <br> | + | <br><code>None</code> – Bluetooth® functionality will be disabled. <br> |
− | <code>Sensors</code> – Enables Bluetooth functionality for sensors. <br> | + | <code>Sensors</code> – Enables Bluetooth® functionality for sensors. <br> |
| | | |
| '''Update frequency''' – how often BLE scanning will run. <br> | | '''Update frequency''' – how often BLE scanning will run. <br> |
Line 100: |
Line 106: |
| '''To ENABLE backup feature on TAT100 device:''' | | '''To ENABLE backup feature on TAT100 device:''' |
| | | |
− | # <code>Bluetooth</code> → select <code>Backup Tracker</code><br> | + | # <code>Bluetooth®</code> → select <code>Backup Tracker</code><br> |
| # Enter main device (FMBxxx/TFT100/TST100/GH5200/TMT250) IMEI<br> | | # Enter main device (FMBxxx/TFT100/TST100/GH5200/TMT250) IMEI<br> |
| # Set <b>Update frequency</b> to <b>3600</b> (s) – <i>We do not recommend to set values below <b>1800</b> sec. in this field, as it will shorten the battery life.</i><br> | | # Set <b>Update frequency</b> to <b>3600</b> (s) – <i>We do not recommend to set values below <b>1800</b> sec. in this field, as it will shorten the battery life.</i><br> |
Line 106: |
Line 112: |
| | | |
| | | |
− | [[File:TAT100_Bluetooth_Backup_v2.png|center|400px]] | + | [[File:TAT100_Bluetooth®_Backup_v2.png|center|400px]] |
| | | |
| | | |
| '''To ENABLE backup feature on FMBXXX/TFT100/TST100/GH5200/TMT250 devices:''' | | '''To ENABLE backup feature on FMBXXX/TFT100/TST100/GH5200/TMT250 devices:''' |
| | | |
− | #<code>Bluetooth</code> → <code>BT Radio</code> set to <code>Enable(visible)</code><br><br>[[File:BT ONN.jpg|center|500px]]<br> | + | #<code>Bluetooth®</code> → <code>BT Radio</code> set to <code>Enable(visible)</code><br><br>[[File:BT ONN.jpg|center|500px]]<br> |
| #ENABLE backup feature on: | | #ENABLE backup feature on: |
− | ##<b>TFT100 | TST100 | GH5200 | TMT250</b> devices<br><code>Bluetooth 4.0</code> → <code>Backup Tracker</code> set to <code>Enabled</code><br><br>[[File:TAT100_bluetooth_backup_enable.png|center|700px]]<br> | + | ##<b>TFT100 | TST100 | GH5200 | TMT250</b> devices<br><code>Bluetooth® 4.0</code> → <code>Backup Tracker</code> set to <code>Enabled</code><br><br>[[File:TAT100_bluetooth_backup_enable.png|center|700px]]<br> |
− | ##<b>FMBXXX</b> devices<br>Instructions on how to configure the FMBXXX device can be found [https://wiki.teltonika-gps.com/view/FMC130_Bluetooth_4.0_settings#Backup_Tracker here]. | + | ##<b>FMBXXX</b> devices<br>Instructions on how to configure the FMBXXX device can be found [https://wiki.teltonika-gps.com/view/FMC130_Bluetooth®_4.0_settings#Backup_Tracker here]. |
| | | |
| ==DEVICE RECOGNITION CHECK USING TERMINAL== | | ==DEVICE RECOGNITION CHECK USING TERMINAL== |
Line 136: |
Line 142: |
| 3. When TAT100 cannot see the main tracker Terminal will print a line as shown in example below:<br> | | 3. When TAT100 cannot see the main tracker Terminal will print a line as shown in example below:<br> |
| <code>[2021.10.26 10:50:03] – [ASSET.UART] << [2021.10.26 10:50:03] – [APP.TBT] ERROR! Amount of valid packets does not detect during this period! Triggering alarm </code><br> | | <code>[2021.10.26 10:50:03] – [ASSET.UART] << [2021.10.26 10:50:03] – [APP.TBT] ERROR! Amount of valid packets does not detect during this period! Triggering alarm </code><br> |
− |
| |
− | ==Disclaimer==
| |
− |
| |
− | [[File:Alert.png|left|link=]] <br> If you are not using Bluetooth, '''please consider turning it off''' or '''change Bluetooth PIN''' to remove potential risks.
| |
− |
| |
− | If you are using Bluetooth we strongly recommend '''using AES encryption''' for enhanced security.
| |
− |
| |
− |
| |
− | [[Category:TAT100 Configuration]]
| |