312
edits
Changes
no edit summary
'''NOTE:''' If you do not insert microSD card, you will be only available to receive images, but you do not receive video if the trigger will happen or you will send SMS/GPRS command.
'''NOTE:''' If you do not insert microSD card, you will be only available to receive images, but you do not receive video if the trigger will happen or you will send SMS/GPRS command.
[[image:548772 DASHBOARD 1.jpg|400px]]
[[image:548772 DASHBOARD 1.jpg|400px]]
==Mounting recommendation==
==Mounting recommendation==
Camera location:
Camera location:
* Camera must be mounted as shown in the picture below, you can stick it to window using 3M duct tape, or you can use screws fit to other surfaces.
* Camera must be mounted on the windshield of the, you can stick it to window using 3M duct tape, or you can use screws fit to other surfaces.
* To maximize the field of view, the camera should be mounted in the middle of the front windshield so that an even field of view for the sides of the vehicle is recorded. We recommend you mount the DashCam near the rearview mirror area.
* To maximize the field of view, the camera should be mounted in the middle of the front windshield so that an even field of view for the sides of the vehicle is recorded. We recommend you mount the DashCam near the rearview mirror area.
* We always recommend angling the lens slightly upwards so that video footage displays about 60% road and 40% sky. This angle offers a good balance of exposure and details.
* We always recommend angling the lens slightly upwards so that video footage displays about 60% road and 40% sky. This angle offers a good balance of exposure and details.
[[File:Dashcam ignition connection.jpg|frameless|928x928px]]
[[File:2Dashcam ignition connection.jpg|frameless|928x928px]]
If you need to receive additional data from the DashCam when the ignition is off, you can do it by connecting the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [https://wiki.teltonika-gps.com/view/FMB_setdigout FMB DOUT].
If you need to receive additional data from the DashCam when the ignition is off, you can do it by connecting the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [https://wiki.teltonika-gps.com/view/FMB_setdigout FMB DOUT].
[[File:DashCam dout connection.jpg|frameless|928x928px]]
[[File:Reley2.PNG|frameless|928x928px]]
'''DASHCAM FMC650 Installation with Ignition Source'''. To connect the DashCam to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.
'''NOTE:''' DashCam must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.
[[File:DashCam and FMC650 Ignition source.png|frameless|928x928px]]
'''DASHCAM FMC650 Installation with Relay'''. If you need to receive additional data from the DashCam when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].
[[File:DashCam and FMC650 relay.png|frameless|928x928px]]
'''Two cameras FMC650 Installation with Ignition Source'''. To connect the two cameras to the FMC650 device, you have to make sure to connect 4 PIN's of the camera to the PIN's of your device correctly.
'''NOTE:''' Two cameras must be connected to the ignition source or another source, where then you turn off ignition camera will turn off in another case camera will drain the battery if you connect directly.
[[File:688548 DualCam and DSM with FMC650.jpg]]
'''Two cameras FMC650 Installation with Relay'''. If you need to receive additional data from the Two cameras or one of them when the ignition is off, you can also connect the camera to a power source using the relay, to control the power supply by turning on/off the camera. To find information on how to configure DOUT, please visit [[FMB setdigout|FMB DOUT]].
[[File:2 cameras dout.JPG|frameless|928x928px]]
{| class="wikitable"
{| class="wikitable"