|
|
| (9 intermediate revisions by one other user not shown) |
| Line 1: |
Line 1: |
| <b>{{{description|Small and smart tracker}}}</b>
| | {{Template:FTX First Start|model=FTC921}} |
| {{{pic|[[Image:FTC921.png|400px|right]]}}}
| |
| <br>
| |
| | |
| __TOC__
| |
| | |
| | |
| =='''HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY'''==
| |
| | |
| {{{with_battery|
| |
| # Gently remove {{{model|FTC921}}} '''cover''' using '''plastic pry tool''' from one side.
| |
| # Gently remove {{{model|FTC921}}} '''cover''' using '''plastic pry tool''' from another side.
| |
| # Insert '''{{{sim_type|Nano-}}}SIM''' card as shown. Make sure that {{{sim_type|Nano-}}}SIM card '''cut-off corner''' is pointing forward to slot.
| |
| # Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
| |
| # Attach device '''cover''' back. Device is ready to be connected.}}}
| |
| | |
| {{{SIM1|[[Image:FTC921_How_to_insert_SIM_card_1.png|850px]]}}}
| |
| {{{SIM2|[[Image:FTC921_How_to_insert_SIM_card_2.png|550px]]}}}
| |
| | |
| | |
| {|
| |
| |-
| |
| | [[File:Alert.png|left|link=]] || <b>{{{sim_type|Nano-}}}SIM card insertion/removal must be performed when device is powered off – external voltage {{{battery|and internal battery}}} disconnected. Otherwise {{{sim_type|Nano-}}}SIM card might be damaged or device will not detect it.</b>
| |
| |}
| |
| | |
| =='''PC CONNECTION (WINDOWS)'''==
| |
| 1. Power- up FTC921 with DC voltage (10-90V) power supply using power wires. LEDs should start blinking.
| |
| | |
| 2. Connect device to computer using USB Type-C cable and install USB driver, see “How to install USB drivers (Windows)1”
| |
| | |
| =='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==
| |
| | |
| # Please download COM port drivers from '''[[Media:TeltonikaCOMDriver.zip|here]]'''.
| |
| # Extract and run '''TeltonikaCOMDriver.exe'''.
| |
| # Click '''Next''' in driver installation window.
| |
| # In the following window click '''Install''' button.
| |
| # Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.
| |
| | |
| =='''CONFIGURATION (WINDOWS)'''==
| |
| | |
| At first FTC921 device will have default factory settings set. These settings should be changed according to the user's needs. Main
| |
| configuration can be performed via [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Teltonika Configurator tool (TCT)].
| |
| | |
| =='''MOUNTING RECOMMENDATIONS'''==
| |
| '''CONNECTING WIRES'''
| |
| | |
| * Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.<br />
| |
| * There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.<br />
| |
| * If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be <br />applied and the wires should not be loose.<br />
| |
| * Wires cannot be connected to the board computers or control units.<br />
| |
| | |
| '''CONNECTING POWER SOURCE'''
| |
| | |
| * Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.<br />
| |
| * When module is connected, measure voltage again to make sure it did not decrease.<br />
| |
| * It is recommended to connect to the main power cable in the fuse box.<br />
| |
| * 3 A, 125 V external fuse shall be used.<br />
| |
| | |
| '''CONNECTING GROUND WIRE'''
| |
| | |
| * Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.<br />
| |
| * If the wire is fixed with the bolt, the loop must be connected to the end of the wire.<br />
| |
| * For better contact scrub paint from the spot where loop is going to be connected.<br />
| |
| | |
| [[Category:FTC921]]
| |
