2,556
edits
Changes
FMB640 and Tachograph Solution (view source)
Revision as of 09:44, 23 January 2020
, 09:44, 23 January 2020no edit summary
Before connecting tachograph wires, it is required to measure CAN line resistance
Before connecting tachograph wires, it is required to measure CAN line resistance
while tachograph is switched off:<br />
while tachograph is switched off:<br />
#Turn off the vehicle ignition;<br />
#Measure resistance between the C5 (CAN2 H) and C7 (CAN2 L) contacts;<br />
#If the multimeter shows ~120 Ohms, skip the next step;<br />
#If the multimeter shows kilo Ohms resistance then it is needed to connect tachograph C8 (CAN-RES) and C7 (CAN2 L) contacts with wire and then perform further actions;<br />
#Re-measure the resistance of the line – it has to be ~120 Ohms.<br />
#Connect CAN2 L and CAN2 H wires to tachograph (C5 (CAN2 H) and C7 (CAN2 L))<br />
* All of the same level CAN-L and CAN-H wires must be interlaced with each other.<br />
*All of the same level CAN-L and CAN-H wires must be interlaced with each other.<br />
[[Image:Wires.PNG|800px|center]]
[[Image:Wires.PNG|800px|center]]
* CAN wires need to be installed as far as possible from GSM antenna.<br />
*CAN wires need to be installed as far as possible from GSM antenna.<br />
Below is wiring diagram of Tachograph and FM6400/FMB640 device:<br />
Below is wiring diagram of Tachograph and FM6400/FMB640 device:<br />
==Checking connection (Tachocheck SMS)==
==Checking connection (Tachocheck SMS)==
After successful connection tachocheck SMS message can be sent to device for checking if
After successful connection ''tachocheck'' SMS message can be sent to device for checking if
data presented on connected lines, by another words if connections were done correctly. It is
data presented on connected lines, by another words if connections were done correctly. It is
used for getting status information. SMS response is of such structure:
used for getting status information. SMS response is of such structure:
[T] – Tachograph presence on bus:<br />
[T] – Tachograph presence on bus:<br />
* 0 – Tachograph doesn’t respond on bus;<br />
* 1 – Tachograph responds on bus.
*0 – Tachograph doesn’t respond on bus;<br />
*1 – Tachograph responds on bus.
[R] – Response to Open Remote Session validity check:<br />
[R] – Response to Open Remote Session validity check:<br />
* 0 – Wrong or unknown response (failed to open Remote Session);<br />
* 1 – Tachograph responds positively (Remote Session opened successfully).
*0 – Wrong or unknown response (failed to open Remote Session);<br />
*1 – Tachograph responds positively (Remote Session opened successfully).
[C] – Response to Close Last Authentication Session validity check:<br />
[C] – Response to Close Last Authentication Session validity check:<br />
* 0 – Wrong or unknown response (failed to close last authentication session);<br />
* 1 – Last authentication session closed successfully, device is ready to open new authentication session.
*0 – Wrong or unknown response (failed to close last authentication session);<br />
*1 – Last authentication session closed successfully, device is ready to open new authentication session.
[K] – K-Line data presence on bus:<br />
[K] – K-Line data presence on bus:<br />
* 0 – K-Line data not present on bus;<br />
* 1 – K-Line data present on bus.
*0 – K-Line data not present on bus;<br />
*1 – K-Line data present on bus.
[ABCD] – FMS data presence on bus:<br />
[ABCD] – FMS data presence on bus:<br />
* 0000 – FMS data not present on bus;<br />
* Non-zero – FMS data detected on bus.
*0000 – FMS data not present on bus;<br />
*Non-zero – FMS data detected on bus.
'''SMS answer which shows correct line connections looks like “CAN_2:[111],[ABCD], K-Line:[K]”.'''
'''SMS answer which shows correct line connections looks like “CAN_2:[111],[ABCD], K-Line:[K]”.'''
