Difference between revisions of "Universal Device Test Guide"

From Wiki Knowledge Base | Teltonika GPS
(36 intermediate revisions by 6 users not shown)
Line 1: Line 1:
−
__TOC__
+
[[Image:Qsg_rut950_teltonika.PNG|centre]]__TOC__
−
=='''<big>Introduction</big>'''==
+
=='''How to insert SIM card and connect the battery*'''==
−
[[File:Welcome to the telematics banner 1.1.png]]
 
  
−
Universal Device Testing Guide can be applied to any Teltonika Telematics device. The purpose of this guide is to help new users get acquainted with Teltonika Fleet Management devices and test basic functions in 5 easy steps.
+
# Gently remove '''device cover''' using '''plastic pry tool''' from both sides as it is showed in a 1st picture.
 +
# Insert '''SIM''' card as shown with '''PIN request disabled''' or read [[FMB9YX Security info|'''Security info''']] how to enter it later in Configurator. Make sure that SIM card '''cut-off corner''' is pointing forward to slot.
 +
# Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
 +
# Attach device '''cover''' back. Device is ready to be connected.
  
−
Once you are finished with basic testing, you will find additional instructions on how to test specific use cases and advanced features of our devices as well as remote tracker management platform and other solutions.
 
  
−
In case you have any questions regarding Teltonika devices or their features, do not worry - we have a well of knowledge called '''[[Main Page|Teltonika WIKI]]''', '''[https://community.teltonika.lt/c/teltonika-telematics/6 Teltonika Telematics Community page]''' and our '''[https://www.youtube.com/channel/UCjWIn5amqvtWc7X7tI_04LQ Official Youtube Channel]''', where you can find answers regarding our devices functionalities and specifications.
 
  
−
If you do not find answers to your questions online - do not despair, we have a highly professional team of support engineers who are willing to help and can be reached via Helpdesk.
 
  
−
=='''<big>Basic Testing</big>'''==
+
[[Image:{{{sim_insert_pic1|FMB1_cover1_correct.png}}}|260px]][[Image:{{{sim_insert_pic2|FMB1_cover2_correct.png}}}|260px]][[Image:{{{sim_insert_pic3|FMB1_cover3_correct.png}}}|260px]][[Image:{{{sim_insert_pic4|FMB1_cover4_correct.png}}}|260px]]
−
[[File:5 easy steps to prepare any Teltonika Telematics device banner.png]]  
 
  
−
In this chapter, we will go through 5 easy testing steps which will help you get acquainted with Teltonika Telematics devices. We will cover everything you need to start using the device - from inserting a SIM card, powering the device, and ending with GPS track information directly from your vehicle to the server.
 
  
−
The video below shows the preparation of FMC880 device - please note that the initial steps are universal and can be applied to majority of our devices.
 
  
−
<youtube width="850" height="480">GDGFG6Lh1B0</youtube><br>''*Please note that the '''iot.truphone.com''' APN shown in the video should only be used with Truphone SIM cards - please contact Your network operator for the exact APN details, if You are using different SIM cards.''
+
''
  
−
==='''STEP 1: Prepare the Device'''===
 
−
'''''Result: Device has a SIM card installed and internal battery connected'''''
 
  
−
All our devices use SIM cards for telecommunication, thus you will not be able to get any data and/or communicate with the device remotely without the SIM card. In this chapter, you will find a guide on how to insert a SIM card and connect the internal battery.
 
  
−
''Note:'' Different Teltonika devices use different SIM card types: mini-SIM, micro-SIM, nano-SIM, and [[Requirements for eSIM|'''eSIM''']] (which is soldered during device manufacturing process).
+
'''<nowiki>*</nowiki> If you would like to check how to insert SIM card into your particular device, you will find a link with all devices manuals here.'''
  
−
 
+
{|
−
'''How to insert SIM card and connect the battery?'''
 
−
#Gently remove '''device cover''' using '''plastic pry tool''' from both sides as it is showed in a 1st picture.
 
−
#After opening device cover, you will see '''SIM card''' and '''battery''' connection '''slots'''.
 
−
#Insert '''SIM''' card as shown with '''PIN request disabled''' or read '''[[FMB120 Security info|Security info]]''' (Universal Guide) how to enter it later in Configurator. Make sure that SIM card '''cut-off corner''' is pointing forward to slot.
 
−
#Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
 
−
#Attach device '''cover''' back. Device is ready to be connected.
 
−
 
 
−
 
 
−
You can find how exactly the SIM card has to be inserted (and battery connected, if the device comes with one) by seeing the pictures below:
 
−
 
 
−
 
 
−
<div class="toccolours mw-collapsible mw-collapsed">
 
−
<strong>Basic trackers</strong>
 
−
<div class="mw-collapsible-content">
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB900</strong>
 
 
|-
 
|-
−
|[[Image:Fmb900_cover_1.png|500px]]
+
|[[File:Alert.png|left|link=]]||<b>SIM card insertion/removal must be performed when device is powered off – external voltage {{{battery|and internal battery}}} disconnected. Otherwise SIM card might be damaged or device will not detect it.</b>
−
|[[Image:Fmb900_cover_2.png|500px]]
 
−
|[[Image:Fmb900_cover_3.png|500px]]
 
−
|[[Image:Fmb900_cover_4.png|500px]]
 
 
|}
 
|}
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
=='''PC Connection (Windows)'''==
−
|<strong>FMB910, FMB920, FMB930 </strong>
+
Power-up device with '''DC voltage (10 – 30 V)*''' power supply using '''supplied power cable'''. LED’s should start blinking, see “'''[[LED Status|LED behaviour description]]'''”.
−
|-
+
<span> </span>
−
|{{{SIM1|[[Image:FMB9_sim_ir_battery_insert-1.png|500px]]}}}
 
−
|{{{SIM2|[[Image:FMB9_sim_ir_battery_insert-2.png|500px]]}}}
 
−
|{{{SIM3|[[Image:FMB9_sim_ir_battery_insert-3.png|500px]]}}}
 
−
|{{{SIM4|[[Image:FMB9_sim_ir_battery_insert-4.png|500px]]}}}
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
#Connect device to computer using '''USB cable''' or '''Bluetooth''' connection:
−
|<strong>FMC920, FMM920 </strong>
+
#* Using '''USB cable'''
−
|-
+
#**You will need to install USB drivers, see "[[Universal Device Test Guide#How to install USB drivers (Windows)|'''How to install USB drivers (Windows)''']]"
−
|{{{SIM1|[[File:FMC920 1.png|500px]]}}}
+
#* Using '''Bluetooth'''
−
|{{{SIM2|[[File:FMC920 2.png|500px]]}}}
+
#**Device Bluetooth is enabled by default. Turn on '''Bluetooth''' on your PC, then select '''Add Bluetooth or other device > Bluetooth'''. Choose your device named – “'''FMxyzw_last_7_imei_digits'''”, without '''LE''' in the end. Enter default password '''5555''', press '''Connect''' and then select '''Done'''. Keep in mind that the FMx640 devices do not support configuration via Bluetooth.
−
|{{{SIM3|[[File:FMC920 3.png|500px]]}}}
+
#You are now ready to use the device on your computer.
−
|{{{SIM4|[[File:FMC920 4.png|500px]]}}}
 
−
|{{{SIM5|[[File:FMC920_5.png|500px]]}}}
 
−
|{{{SIM5|[[File:FMC920_6.png|500px]]}}}
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB965</strong>
 
−
|-
 
−
|{{{SIM1|[[Image:FMB965_sim_ir_battery_insert-1.png|260px]]}}}
 
−
|{{{SIM2|[[Image:FMB965_sim_ir_battery_insert-2.png|260px]]}}}
 
−
|{{{SIM3|[[Image:FMB965_sim_ir_battery_insert-3.png|260px]]}}}
 
−
|{{{SIM4|[[Image:FMB965_sim_ir_battery_insert-4.png|260px]]}}}
 
−
|{{{SIM4|[[Image:FMB965_sim_ir_battery_insert-5.png|260px]]}}}
 
−
|{{{SIM4|[[Image:FMB965_sim_ir_battery_insert-6.png|260px]]}}}
 
−
|}
 
−
</div>
 
−
</div>
 
  
−
<div class="toccolours mw-collapsible mw-collapsed">
+
''* FMB900, FMB910, FMB920, MTB100, FMB202, FMB204 devices support '''(6 - 30 V)'''  DC power supply.''<span></span>
−
<strong>Fast & Easy trackers</strong>
 
−
<div class="mw-collapsible-content">
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMP100</strong>
 
−
|-
 
−
|[[Image:FMP100 1.png|300px]]
 
−
|[[Image:FMP100 2.png|300px]]
 
−
|[[Image:FMP100 3.png|300px]]
 
−
|[[Image:FMP100 4.png|300px]]
 
−
|[[Image:FMP100 5.png|300px]]
 
−
|[[Image:FMP1000 6.png|300px]]
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
=='''How to install USB drivers (Windows)'''==
−
|<strong>FMB010</strong>
 
−
|-
 
−
|{{{insert1|[[Image:Fmb010_cover_1.png|280px]]}}}
 
−
|{{{insert2|[[Image:Fmb010_cover_2.png|280px]]}}}
 
−
|{{{insert3|[[Image:Fmb010_battery_1.png|280px]]}}}
 
−
|{{{insert4|[[Image:Fmb010_cover_3.png|280px]]}}}
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
#Please download COM port drivers from Teltonika '''[https://teltonika-gps.com/downloads/en/fmb120/TeltonikaCOMDriver.zip here]'''.
−
|<strong>FMB020</strong>
+
#Extract and run '''TeltonikaCOMDriver.exe'''.
−
|-
+
# Click '''Next''' in driver installation window.
−
|{{{insert1|[[Image:Fmb020 card 1.png|280px]]}}}
+
#In the following window click '''Install''' button.
−
|{{{insert2|[[Image:Fmb020 card 2.png|280px]]}}}
+
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.
−
|{{{insert3|[[Image:Fmb020 card 3.png|280px]]}}}
 
−
|{{{insert4|[[Image:Fmb020 card 4.png|280px]]}}}
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
=='''Configuration (Windows)'''==
−
|<strong>FMC800, FMM800, FMM80A</strong>
 
−
|-
 
−
|{{{insert1|[[Image:Fmm001_cover_1.png|280px]]}}}
 
−
|{{{insert2|[[Image:Fmm0001_cover_2.png|280px]]}}}
 
−
|{{{insert3|[[Image:Fmm001_battery_1.png|280px]]}}}
 
−
|{{{insert4|[[Image:Fmm001_cover_3.png|280px]]}}}
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
At first device will have default factory settings set. These settings should be changed according to the user's needs.<br />
−
|<strong>FMT100, FMC880, FMM880</strong>
+
Main configuration can be performed via '''[[Teltonika Configurator]]''' software. Get the latest '''Configurator''' version from '''[[{{{SAS_Configurator_Versions|Teltonika Configurator versions}}}|here]]'''. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
−
|-
 
−
||[[Image:FMT100_sim_insert-1.png|170px]]&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;[[Image:FMT100_sim_insert-2.png|170px]]
 
−
|[[Image:FMT100_sim_insert-3.png|170px]]&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;[[Image:FMT100_sim_insert-4.png|170px]]
 
−
|[[Image:FMT100_sim_insert-5.png|170px]]&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;[[Image:FMT100_sim_insert-6.png|170px]]
 
−
|}
 
−
</div>
 
−
</div>
 
  
−
<div class="toccolours mw-collapsible mw-collapsed">
+
{| class="wikitable" style="width:50%;"
−
<strong>Advanced trackers</strong>
+
|+
−
<div class="mw-collapsible-content">
+
! colspan="4" style="width:50%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |MS .NET requirements
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB110</strong>
 
−
|-
 
−
|[[Image:{{{sim_insert_pic1|FMB110-Battery-1.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic2|FMB110-Battery-2.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic3|FMB110-Battery-3.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic4|FMB110-Battery-4.png}}}|260px]]
 
−
|}
 
−
 
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB120, FMB122, FMB130, FMC130, FMM130</strong>
 
−
|-
 
−
|[[Image:{{{sim_insert_pic1|FMB1_cover1_correct.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic2|FMB1_cover2_correct.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic3|FMB1_cover3_correct.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic4|FMB1_cover4_correct.png}}}|260px]]
 
−
|}
 
−
 
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMC13A, FMM13A</strong>
 
−
|-
 
−
|[[Image:FMC13A_cover1_correct.png|280px]]
 
−
|[[Image:FMC13A_cover2_correct.png|280px]]
 
−
|[[Image:FMC13A_cover3_correct.png|280px]]
 
−
|[[Image:FMC13A_cover4_correct.png|280px]]
 
−
|}
 
−
 
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB202, FMB204, FMB209</strong>
 
 
|-
 
|-
−
|[[Image:case7.png|250px]]
+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Operating system
−
|[[Image:case4.png|250px]]
+
! style="width:25%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |MS .NET Framework version
−
|[[Image:case2.png|250px]]
+
! style="width:10%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Version
−
|[[Image:case5.png|250px]]
+
! style="width:5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;" |Link
−
|[[Image:case3.png|250px]]
 
−
|[[Image:case6.png|250px]]
 
−
|}
 
−
 
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB230</strong>
 
 
|-
 
|-
−
|[[Image:FMX2YX_cover_open1_correct.png|280px]]
+
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |<ul style="list-style: none; margin: 0px;">
−
|[[Image:FMX2YX_cover2_correct.png|280px]]
+
<li>Windows Vista</li>
−
|[[Image:FMX2YX cover3 correct.png|280px]]
+
<li>Windows 7</li>
−
|[[Image:FMX2YX_cover4_correct.png|280px]]
+
<li>Windows 8.1</li>
−
|[[Image:FMX2YX_cover5_correct.png|middle|280px]]
+
<li>Windows 10</li>
−
|[[Image:FMX2YX_cover6_correct.png|middle|280px]]
+
</ul>
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |MS .NET Framework 4.6.2
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |32 and 64 bit
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |[https://www.microsoft.com/en-us/download/confirmation.aspx?id=53344 www.microsoft.com]
 
|}
 
|}
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
Launch '''Configurator.exe'''. After launch software language can be changed by clicking [[File:Language_icon.png|25px|link=]] in the right bottom corner:
−
|<strong>FMC230, FMM230, FMC234</strong>
 
−
|-
 
−
|[[Image:FMX2YX_cover_open1_correct.png|280px]]
 
−
|[[Image:FMX2YX_cover2_correct.png|280px]]
 
−
|[[Image:FMX2YX SIM insert FMC230.png|280px]]
 
−
|[[Image:FMX2YX_cover4_correct.png|280px]]
 
−
|[[Image:FMX2YX_cover5_correct.png|middle|280px]]
 
−
|[[Image:FMX2YX_cover6_correct.png|middle|280px]]
 
−
|}
 
−
</div>
 
−
</div>
 
−
 
 
−
<div class="toccolours mw-collapsible mw-collapsed">
 
−
<strong>OBD trackers</strong>
 
−
<div class="mw-collapsible-content">
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB001</strong>
 
−
|-
 
−
|{{{insert1|[[Image:Fmb010_cover_1.png|280px]]}}}
 
−
|{{{insert2|[[Image:Fmb010_cover_2.png|280px]]}}}
 
−
|{{{insert3|[[Image:Fmb010_battery_1.png|280px]]}}}
 
−
|{{{insert4|[[Image:Fmb010_cover_3.png|280px]]}}}
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
[[File:FMB_Configurator_language.jpg|400px]]
−
|<strong>FMB002, FMB003</strong>
 
−
|-
 
−
|{{{insert1|[[Image:Fmb020 card 1.png|280px]]}}}
 
−
|{{{insert2|[[Image:Fmb020 card 2.png|280px]]}}}
 
−
|{{{insert3|[[Image:Fmb020 card 3.png|280px]]}}}
 
−
|{{{insert4|[[Image:Fmb020 card 4.png|280px]]}}}
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
Configuration process begins by pressing on connected device:
−
|<strong>FMC001, FMC003, FMC00A, FMM001, FMM003, FMM00A</strong>
 
−
|-
 
−
|{{{insert1|[[Image:Fmm001_cover_1.png|280px]]}}}
 
−
|{{{insert2|[[Image:Fmm0001_cover_2.png|280px]]}}}
 
−
|{{{insert3|[[Image:Fmm001_battery_1.png|280px]]}}}
 
−
|{{{insert4|[[Image:Fmm001_cover_3.png|280px]]}}}
 
−
|}
 
−
</div>
 
−
</div>
 
  
−
<div class="toccolours mw-collapsible mw-collapsed">
+
[[File:Faceless_configurator_select.png]]
−
<strong>CAN trackers</strong>
 
−
<div class="mw-collapsible-content">
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB140, FMC150, FMM150</strong>
 
−
|-
 
−
|[[Image:{{{sim_insert_pic1|FMB1_cover1_correct.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic2|FMB1_cover2_correct.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic3|FMB1_cover3_correct.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic4|FMB1_cover4_correct.png}}}|260px]]
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
After connection to Configurator '''Status window''' will be displayed:
−
|<strong>FMB240</strong>
 
−
|-
 
−
|[[Image:FMX2YX_cover_open1_correct.png|280px]]
 
−
|[[Image:FMX2YX_cover2_correct.png|280px]]
 
−
|[[Image:FMX2YX SIM insert FMC230.png|280px]]
 
−
|[[Image:FMX2YX_cover4_correct.png|280px]]
 
−
|[[Image:FMX2YX_cover5_correct.png|middle|280px]]
 
−
|[[Image:FMX2YX_cover6_correct.png|middle|280px]]
 
−
|}
 
−
</div>
 
−
</div>
 
  
−
<div class="toccolours mw-collapsible mw-collapsed">
+
[[File:Faceless_configurator.png]]
−
<strong>Professional trackers</strong>
 
−
<div class="mw-collapsible-content">
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>FMB641</strong>
 
−
|-
 
−
|[[Image:Fmb640FMB640111.png|260px]]
 
−
|[[Image:Fmb640-FMB640222.png|260px]]
 
−
|[[Image:Fmb640FMB640333.png|260px]]
 
−
|[[Image:Fmb640FMB640444.png|260px]]
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
Various '''[[{{{model|FMB1YX}}}_Status_info|Status window]]''' tabs display information about '''[[{{{model|FMB1YX}}}_Status_info#GNSS_Info|GNSS]], [[{{{model|FMB1YX}}}_Status_info#GSM_Info|GSM]], [[{{{model|FMB1YX}}}_Status_info#I.2FO_Info|I/O]], [[{{{model|FMB1YX}}}_Status_info#Maintenance|Maintenance]]''' and etc. {{{model|FMB1YX}}} can be loaded and saved to the device. After any modification of configuration changes need to be saved to device using '''Save to device''' button. Main buttons offer following functionalities:<br />
−
|<strong>FMC650, FMM650</strong>
+
#[[File:Load_from_device.png|25px|link=]] '''Load from device''' – loads configuration from device.
−
|-
+
#[[File:Save_to_device.png|25px|link=]] '''Save to device''' – saves configuration to device.
−
|[[Image:{{{sim_insert_pic1|{{{model|Fmb640}}}-cover-1.png}}}|260px]]
+
#[[File:Load_from_file.png|25px|link=]] '''Load from file''' – loads configuration from file.
−
|[[Image:{{{sim_insert_pic2|{{{model|Fmb640}}}-cover-2.png}}}|260px]]
+
#[[File:Save_to_file.png|25px|link=]] '''Save to file''' – saves configuration to file.
−
|[[Image:{{{sim_insert_pic3|{{{model|Fmb640}}}-cover-3.png}}}|260px]]
+
#[[File:Firmware_update.png|link=|25x25px]]<span> </span>'''Update firmware'''<span> – updates firmware on device.</span>
−
|[[Image:{{{sim_insert_pic4|{{{model|Fmb640}}}-cover-4.png}}}|260px]]
+
#[[File:Read_records.png|25px|link=]] '''Read records''' – read records from device.
−
|[[Image:{{{sim_insert_pic4|{{{model|Fmb640}}}-cover-5.png}}}|260px]]
+
#[[File:Reboot_device.png|25px|link=]] '''Reboot device''' – restarts device.
−
|[[Image:{{{sim_insert_pic4|{{{model|Fmb640}}}-cover-6.png}}}|260px]]
+
#[[File:Reset_configuration.png|25px|link=]] '''Reset configuration''' – sets device configuration to default.
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
Most important configurator sections are GPRS – where all your server and '''GPRS settings''' can be configured and '''Data Acquisition''' – where data acquiring parameters can be configured.
−
|<strong>FMB125, FMC125, FMM125</strong>
+
More details about devices configuration using Configurator and more information about your particular device can be found [[Main Page|'''{{{config_link|in the manual}}}'''.]]
−
|-
 
−
|[[Image:{{{sim_insert_pic1|FMB1_cover1_correct.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic2|FMB122-Battery-Sim-2.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic3|FMB1_cover3_correct.png}}}|260px]]
 
−
|[[Image:{{{sim_insert_pic4|FMB1_cover4_correct.png}}}|260px]]
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
=='''Quick SMS configuration'''==
−
|<strong>FMC225</strong>
 
−
|-
 
−
|[[Image:FMX2YX_cover_open1_correct.png|280px]]
 
−
|[[Image:FMX2YX_cover2_correct.png|280px]]
 
−
|[[Image:FMX2YX SIM insert FMC230.png|280px]]
 
−
|[[Image:FMX2YX_cover4_correct.png|280px]]
 
−
|[[Image:FMX2YX_cover5_correct.png|middle|280px]]
 
−
|[[Image:FMX2YX_cover6_correct.png|middle|280px]]
 
−
|}
 
−
</div>
 
−
</div>
 
  
−
<div class="toccolours mw-collapsible mw-collapsed">
+
Default configuration has optimal parameters present to ensure best performance of track quality and data usage.<br />
−
<strong>Autonomous trackers</strong>
+
Quickly set up your device by sending this SMS command to it:
−
<div class="mw-collapsible-content">
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>TAT100, TAT140, TAT240</strong>
 
−
|-
 
−
|[[Image:TAT100 Cover off.png|275px]]
 
−
|[[Image:TAT100 SIM in.png|275px]]
 
−
|[[Image:TAT100 Device on V3.png|275px]]
 
−
|[[Image:TAT100 Cover on.png|275px]]
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
"  setparam <span style="background-color:#91b9d4;">2001</span>:APN;<span style="background-color:#91d4b9;">2002</span>:APN_username;<span style="background-color:#b991d4;">2003</span>:APN_password;<span style="background-color:#b9d491;">2004</span>:Domain;<span style="background-color:#d491b9;">2005</span>:Port;<span style="background-color:#d4b991;">2006</span>:0"
−
|<strong>TMT250</strong>
 
−
|-
 
−
|[[Image:Tmt250battery1.png|185px]]
 
−
|[[Image:Tmt250battery2.png|185px]]
 
−
|[[Image:Tmt250battery3.png|185px]]
 
−
|[[Image:Tmt250battery4.png|185px]]
 
−
|[[Image:Tmt250battery5.png|185px]]
 
−
|[[Image:Tmt250battery6.png|185px]]
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
<div style="column-count:2;-moz-column-count:2;-webkit-column-count:2">
−
|<strong>GH5200</strong>
+
GPRS settings:
−
|-
+
* <span style="background-color:#91b9d4;">2001</span> – APN
−
|[[Image:GH5200 battery sim insert-1.jpg|250px]]
+
* <span style="background-color:#91d4b9;">2002</span> – APN username (if there are no APN username, empty field should be left)
−
|[[Image:GH5200 battery sim insert-2.jpg|250px]]
+
* <span style="background-color:#b991d4;">2003</span> – APN password (if there are no APN password, empty field should be left)
−
|[[Image:GH5200 battery sim insert-3.jpg|250px]]
+
Server settings:
−
|[[Image:GH5200 battery sim insert-4.jpg|250px]]
+
* <span style="background-color:#b9d491;">2004</span> – Domain
−
|}
+
* <span style="background-color:#d491b9;">2005</span> – Port
 +
* <span style="background-color:#d4b991;">2006</span> – Data sending protocol (0 – TCP, 1 – UDP)
 
</div>
 
</div>
−
</div>
 
−
 
−
<div class="toccolours mw-collapsible mw-collapsed">
 
−
<strong>E-Mobility trackers</strong>
 
−
<div class="mw-collapsible-content">
 
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
 
−
|<strong>TST100</strong>
 
−
|-
 
−
|[[Image:TST100_setup_1.jpg|250px]]
 
−
|[[Image:TST100_setup_2.jpg|250px]]
 
−
|[[Image:TST100_setup_3.jpg|250px]]
 
−
|[[Image:TST100_setup_4.jpg|250px]]
 
−
|[[Image:TST100_setup_5.png|250px]]
 
−
|[[Image:TST100_setup_6.jpg|250px]]
 
−
|[[Image:TST100_setup_7.jpg|250px]]
 
−
|}
 
  
−
{| class="wikitable mw-collapsible mw-collapsed" role="presentation"
+
'''Note''': Before SMS text, two space symbols should be inserted.<br /><br />
−
|<strong>TFT100</strong>
+
[[File:IOS sms cfg.png|235px|right]]
−
|-
 
−
|[[Image:Cover1.png|250px]]
 
−
|[[Image:Cover2.png|250px]]
 
−
|[[Image:Cover3.png|250px]]
 
−
|[[Image:Cover4.png|250px]]
 
−
|[[Image:Cover5.png|250px]]
 
−
|}
 
−
</div>
 
−
</div>
 
  
 +
{{{quick_sms_tmt|<table style="width:70%">
 +
  <tr>
 +
    <td colspan="4">'''Default configuration settings'''</td>
 +
  </tr>
 +
  <tr>
 +
    <td colspan="4">Movement and ignition detection:</td>
 +
  </tr>
 +
  <tr>
 +
    <td>[[File:Accelerometer.png|65px]]</td>
 +
    <td>Vehicle movement will be detected by accelerometer</td>
 +
    <td>[[File:Ignition detection-2-2.png|65px]]</td>
 +
    <td>Ignition will be detected by vehicle power voltage between 13,2 – 30 V</td>
 +
  </tr>
 +
  <tr>
 +
    <td colspan="4">Device makes a record '''On Moving''' if one of these events happen:</td>
 +
  </tr>
 +
  <tr>
 +
    <td>[[File:300s_icon_2.png|65px]]</td>
 +
    <td>300 seconds passes</td>
 +
    <td>[[File:Angle_10_2.png|65px]]</td>
 +
    <td>Vehicle turns 10° degrees</td>
 +
  </tr>
 +
  <tr>
 +
    <td>[[File:Min_distance.png|65px]]</td>
 +
    <td>Vehicle drives 100 meters</td>
 +
    <td>[[File:Speed_delta.png|65px]]</td>
 +
    <td>Speed difference between last coordinate and current position is greater than 10 km/h</td>
 +
  </tr>
 +
  <tr>
 +
    <td colspan="4">Device makes a record '''On Stop''' if:</td>
 +
  </tr>
 +
  <tr>
 +
    <td>[[File:1h_icon.png|65px]]</td>
 +
    <td>1 hour passes while vehicle is stationary and ignition is off</td>
 +
  </tr>
 +
  <tr>
 +
    <td colspan="4">Records sending to server:</td>
 +
  </tr>
 +
  <tr>
 +
    <td>[[File:120_s.png|65px]]</td>
 +
    <td>If device has made a record it is sent to the server every 120 seconds</td>
 +
  </tr>
 +
</table>}}}
  
−
{|
+
<br />
−
|-
+
<p>After successful SMS configuration, device will '''synchronize time''' and '''update records''' to '''configured server'''. More SMS commands can be found '''[[FMB SMS/GPRS Commands|here.]]'''</p>
−
|[[File:Alert.png|left|link=]]||<b>SIM card insertion/removal must be performed when device is powered off – external voltage {{{battery|and internal battery}}} disconnected. Otherwise SIM card might be damaged or device will not detect it.</b>
 
−
|}
 
  
 +
{{{mounting_recommendations|=='''Mounting recommendations'''==
  
−
==='''STEP 2: Connect the device to PC'''===
+
{{{connecting_wires|* <big>Connecting wires</big>
−
'''''Result: Device is connected to the PC and powered with a power supply, allowing the user to configure it.'''''
+
{{{plugged_in|** Wires should be connected while the module is not plugged in.}}}
 +
:* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
 +
:* There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.
 +
:* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.
 +
:* Wires cannot be connected to the board computers or control units.
 +
}}}
  
−
One way to control your device is by connecting it to a PC. During this step, we will introduce you to how to establish the connection.
+
{{{connecting_power_source|* <big>Connecting power source</big>
 +
** Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.
 +
** When module is connected, measure voltage again to make sure it did not decrease.
 +
** It is recommended to connect to the main power cable in the fuse box.
 +
** 3 A, 125 V external fuse shall be used.
 +
}}}
  
−
'''How to install USB drivers (Windows)?'''
+
{{{connecting_ignition|* <big>Connecting ignition wire</big>
 +
**Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
 +
**Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
 +
**Check if power is still available when you turn off any of vehicles devices.
 +
**Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
 +
}}}
  
−
Download COM port drivers from Teltonika '''[[Media:TeltonikaCOMDriver.zip|here]]''' and install them.
+
{{{connecting_ground_wire|* <big>Connecting ground wire</big>
 +
**Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
 +
**If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
 +
**For better contact scrub paint from the spot where loop is going to be connected.
 +
}}}
 +
{{{pay_attention|{{Template:Pay_attention|model={{{model|device}}}}}}}}
 +
}}}
  
−
'''PC Connection (Windows)'''
 
  
−
Power-up device with '''DC voltage (10 – 30 V)*''' power supply using '''supplied power cable**'''. LED’s should start blinking, see “'''[[LED Status|LED behaviour description]]'''”.
+
=='''Installation instructions'''==
−
<span> </span>
 
  
−
Connect device to computer*** using '''USB cable''' or '''Bluetooth®''' connection.
+
In case device has internal GNSS antenna it should be mounted with the logo facing towards open sky
 +
(metal free)
  
 +
[[File:Faceless_device.jpg|center|]]
  
−
''* FMB900, FMB910, FMB920, MTB100, FMB202, FMB204 devices support '''(6 - 30 V)'''  DC power supply.''
 
  
−
<nowiki>**</nowiki> FMP100, FMB002, FMB020, FMB003 can be powered up and configured via USB without any need for an external power supply.
 
  
−
<nowiki>***</nowiki> If you would like to check how to connect your particular device to PC, please see device [[Main Page|'''Teltonika WIKI documentation.''']] Click on ''your device'' -> First Start -> PC Connection (Windows)
+
Device can be mounted under the plastic panel behind the front window, with the sticker direction to a window (sky). It is recommended to place device behind dashboard as close to the window as possible. A good example of GNSS antenna placement is displayed in a picture below (area colored green).
  
−
==='''STEP 3: Configure the Device'''===
+
SIM card should be inserted in the module while the connector is plugged off (while module has no power).
−
'''''Result: Device is configured to generate and send records to the specified server.'''''
 
  
−
After powering up your device, it should be configured to meet your needs. Here you will find steps on how to prepare your device for a first start.
+
[[File:FMB120 install2.jpg|center|]]
  
 +
==<span style="color:#FF0000">'''Safety information'''</span>==
  
−
'''Configuration'''
 
  
−
At first, the device will have default factory settings set. These settings should be changed according to the user's needs.<br />
+
===Precautions===
−
Main configuration can be performed via '''[[Teltonika Configurator]]''' software. Get the latest '''Configurator''' version from '''[[{{{SAS_Configurator_Versions|Teltonika Configurator versions}}}|here.]]''' Configurator operates on Microsoft Windows OS and uses prerequisite latest MS .NET Framework.
 
  
−
The configuration process begins by pressing on the connected device:
+
This message contains information on how to operate device safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!
 +
{{{SELV|* The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is {{{voltage|+10..+30}}}V DC.}}}
 +
*To avoid mechanical damage, it is advised to transport the device in an impact-proof package. {{{LED_indicators|Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.}}}
 +
{{{FMB0_3_ignition|*Before unmounting the device from the vehicle, ignition '''MUST be OFF'''.}}}
 +
{{{connecting|* When connecting the {{{wires|wires}}}{{{2x6_wires|2x6 connector wires to the vehicle}}}{{{1x5_wires|connection (1x5) cables to the vehicle}}}, the appropriate jumpers of the vehicle power supply should be disconnected.}}}
 +
{{{FMB2_connecting_cables|* When installing the connection cables to the vehicle, the appropriate jumpers of the power supply of the vehicle should be disconnected.}}}
 +
{{{unmounting|* Before unmounting the device from the vehicle, the {{{2x6_connector|2x6 connector}}} {{{1x5_connection|1x5 connection}}} must be disconnected.}}}
 +
{{{zone_of_limited|* The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.}}}<br>
 +
{{{boats|* The devices are not designed as a navigational device for boats.}}}
  
−
[[File:Faceless_configurator_select.png|370x370px]]
 
  
−
After connection to Configurator '''Status window''' will be displayed.
 
  
−
In the status window, you will be able to see crucial information that influences device operation such as GNSS and GSM statuses.
+
{| class="wikitable" style="border-style: solid; border-width: 0px"
−
 
+
|+  
−
GNSS Info tab contains GNSS Status, Satellites, and Location information.
 
−
 
 
−
*GNSS Status describes whether the module is ON, received/sent GNSS packets count, FIX status and FIX time
 
−
*Satellites provide you information about visible and currently in-use satellites
 
−
*Location provides you the coordinates, speed, altitude, and angle of your current location.
 
−
 
 
−
GSM Info tab contains GSM Status, Records, GPRS Traffic, SMS Count, and Sockets information
 
−
 
 
−
*GSM Status describes modem status, SIM state, GPRS status, signal level, and operator code
 
−
*Records provide you information about sent records count and the date of the last record sent/server response
 
−
*GPRS Traffic contains information about data usage
 
−
*SMS Count shows you sent/received SMS count
 
−
*Sockets provide status about AVL Data server communication
 
−
 
 
−
{| class="wikitable"
 
−
|+
 
−
GNSS/GSM Status
 
−
!Illustration
 
−
!Description of most important parameters
 
 
|-
 
|-
−
! rowspan="2" |[[File:GNSS Info.png|frameless|800x800px]]
+
| style="text-align: left; background: #F6F6FB;"         | [[Image:Bw_nb.png|50px]]
−
|Module status - here you will be able to see whether the module is ON or in Sleep mode.
+
| style="text-align: left; background: #F6F6FB;"        | '''Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.'''
 
|-
 
|-
−
|Fix Status - Fix/No Fix. For a GNSS fix, at least 4 visible satellites are needed, thus for best performance, the device should be facing an open sky.
+
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_nb.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | '''All wireless data transferring devices produce interference that may affect other devices which are placed nearby.'''
 
|-
 
|-
−
| rowspan="3" |[[File:GSM Info.png|frameless|801x801px]]
+
| style="text-align: left; background: #F6F6FB;"         | [[Image:Bw_key.png|50px]]
−
|Signal Level - make sure that the signal is available in order to send the data to the server.
+
| style="text-align: left; background: #F6F6FB;"        | '''The device must be connected only by qualified personnel.'''
 
|-
 
|-
−
|Type - AVL Data sending status.
+
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_tick.png|50px]]
 +
| style="text-align: left; background: #F6F6FB;"        | '''The device must be firmly fastened in a predefined location.'''
 
|-
 
|-
−
|Socket - Closed or Server domain and port which is used when sending AVL Data via TCP/UDP.
+
| style="text-align: left; background: #F6F6FB;"         | [[Image:Bw_tick.png|50px]]
−
|}
+
| style="text-align: left; background: #F6F6FB;"         | '''The programming must be performed using a PC with autonomic power supply.'''
−
Various '''Status window''' tabs display information about '''GNSS, GSM, I/O, Maintenance''' and etc. configuration can be loaded and saved to the device. '''After changing the configuration, make sure that modifications are saved by clicking "Save to device" button.''' To restore default configuration, click '''"Reset configuration"''' button.
 
−
 
 
−
{| class="wikitable"
 
−
|+
 
−
|[[File:Testing_always_sending.png|alt=|frameless]]
 
−
|'''Note:''' make sure that "Records Saving/Sending Without TS" in System Tab is configured as "Always" ''for testing purposes.''
 
−
This will allow the device to send the data even if there is no GNSS fix (which is hardly obtained inside the buildings) and/or time synchronization.
 
−
|}
 
−
 
 
−
The most important configurator section is GPRS – where all your server and '''GPRS settings''' can be configured and '''Data Acquisition''' – where data acquiring parameters can be configured.
 
−
 
 
−
{| class="wikitable"
 
−
|+
 
−
GPRS Settings
 
−
!Illustration
 
−
!Parameter ID
 
−
!Description
 
−
|-
 
−
! rowspan="3" |[[File:GPRS_settings.png|alt=|frameless|400x400px]]
 
−
|<span style="background-color:#91b9d4;">2001</span>
 
−
|'''A'''ccess '''P'''oint '''N'''ame is a gateway between mobile operator and public internet.
 
−
It can be obtained from your SIM card provider.
 
−
 
 
−
When correct APN settings will be entered device will connect to the internet.
 
−
 
 
−
Note: we do have an auto APN functionality, which is described [[Auto APN feature for FM trackers|'''here''']]
 
 
|-
 
|-
−
|<span style="background-color:#b991d4;">2003</span>
+
| style="text-align: left; background: #F6F6FB;"         | [[Image:Bw_humidity.png|50px]]
−
|APN password (if there are no APN password, empty field should be left)
+
| style="text-align: left; background: #F6F6FB;"        | '''The device is susceptible to water and humidity.'''
 
|-
 
|-
−
|<span style="background-color:#91d4b9;">2002</span>
+
| style="text-align: left; background: #F6F6FB;"         | [[Image:Bw_ecute.png|50px]]
−
|APN username (if there are no APN username, empty field should be left)
+
| style="text-align: left; background: #F6F6FB;"         | '''Installation and/or handling during a lightning storm is prohibited.'''
−
|-
 
−
| rowspan="3" |[[File:SERVER_settings.png|alt=|frameless|400x400px]]
 
−
|<span style="background-color:#b9d491;">2004</span>
 
−
|Domain/IP of destination server
 
−
|-
 
−
|<span style="background-color:#d491b9;">2005</span>
 
−
|Port of destination server
 
−
|-
 
−
|<span style="background-color:#d4b991;">2006</span>
 
−
|Data sending to destination server protocol (0 – TCP, 1 – UDP)
 
 
|}
 
|}
−
[[File:SMS_testing.png|alt=|347x347px|thumb|Picture 4: SMS communication between user and device]]
 
−
 
−
'''Note:''' If you do not have GPS tracking service yet, you can use Teltonika TCP/UDP listener to receive data from the device and Teltonika parser to parse received information. Software can be downloaded from [[Special:Redirect/file/Protocols_and_AVL_parser_pack.zip|'''here.''']] Archive password: 1234
 
−
 
−
<br />
 
−
If you do not want to configure your device via configurator, you can quickly set up your device GPRS settings by sending this SMS command to it:
 
−
"  setparam <span style="background-color:#91b9d4;">2001</span>:APN;<span style="background-color:#91d4b9;">2002</span>:APN_username;<span style="background-color:#b991d4;">2003</span>:APN_password;<span style="background-color:#b9d491;">2004</span>:Domain;<span style="background-color:#d491b9;">2005</span>:Port;<span style="background-color:#d4b991;">2006</span>:0"
 
−
'''Note''': Before SMS text, two space symbols should be inserted.
 
−
 
−
After successful GPRS/SERVER settings configuration, device will '''synchronize time''' and '''update records''' to '''the configured server''' according to the Data Acquisition time intervals. The default configuration has optimal parameters present to ensure the best performance of track quality and data usage. However, '''''for testing''''',  we do recommend these Data Acquisition settings:
 
−
{| class="wikitable"
 
−
|+
 
−
Testing Data Acquisition settings
 
−
!Illustration
 
−
!Parameter ID
 
−
!Description
 
−
|-
 
−
! rowspan="3" |[[File:Testing_Data_Acquisition_V2.png|alt=|frame|Picture 5: Recommended Data Acquisition values for testing purposes]]
 
−
|'''10000'''
 
−
|'''Min period''' indicates time interval in seconds in order to acquire new record.
 
−
|-
 
−
|'''10004'''
 
−
|'''Min Saved Records''' defines the minimum number of records in one data packet that can be sent to the server.
 
−
|-
 
−
|'''10005'''
 
−
|'''Send Period''' indicates time interval in seconds after which the device checks whether it has generated enough records based on the'''Min Saved Records''' parameter. If enough records are generated, the device will send them to the server. If the interval is set to 0 seconds, the device will not send any records to the server.
 
−
 
−
 
−
''Note:'' If the link with the server is already open, records are sent to the server immediately after they are generated.
 
−
|}
 
−
 
−
The device will generate periodic records and send them to the server based on Data Acquisition settings.
 
−
 
−
Using these settings, the device will make a periodic record every 30 seconds and will send it every 30 seconds
 
−
 
−
After testing, Data Acquisition settings should be configured according to your needs.
 
−
 
−
The device will switch operating mode between On Stop and Moving based on configured corresponding movement source status.
 
−
 
−
More details about devices configuration using Configurator and more information about your particular device can be found [[Main Page|'''Teltonika WIKI documentation.''']] Click on ''your device'' -> Configuration.
 
−
 
−
==='''STEP 4: Mount the Device'''===
 
−
'''''Result: Device is mounted in an optimal location, allowing it to have good GNSS and GSM connectivity.'''''
 
−
 
−
Different types of devices have specific mounting instructions: some of them are simple plug-and-play, while other hard-wired devices require professional installation. Please find your specific device mounting instructions [[Main Page|'''Teltonika WIKI documentation.''']] Click on ''your device'' -> First Start -> Mounting recommendations and precautions.
 
−
 
−
 
−
'''Installation instructions'''
 
−
 
−
[[File:Mounting picture 02-01.png|frameless|806x806px]]
 
−
 
−
==='''STEP 5: Track the Device'''===
 
−
'''''Result: User is able to track his device on the tracking platform.'''''
 
−
 
−
Last but not least step for Basic Testing would be to get data/track from your device.
 
−
 
−
This can be done by using either simple TCP/UDP listeners or pre-made tracking platform like listed [[Fleet Management platforms|'''here.''']]
 
−
 
−
Below you can find steps on how to set up a simple TCP/UDP listener on your personal computer.
 
−
 
−
#Open [[Opening TCP/UDP port|'''TCP/UDP port''']]
 
−
#Go to [[Java Parser First Start Guide|'''Java Parser First Start Guide''']]
 
−
 
−
Below you can find pictures of how the track looks on different pre-made tracking platforms:
 
−
 
−
[[File:TAVL jamming.png]]
 
−
 
−
[[File:Wialonturbo.jpg]]
 
−
 
−
=='''<big>Advanced Testing</big>'''==
 
−
 
−
[[File:Discover more device possibilities in-depth banner.png]]
 
−
 
−
In this chapter, we will review advanced device functionalities to get the most out of your Teltonika Telematics device. We will go through some of the specific, widespread use cases, however, keep in mind that device scenarios are not limited to just that. Available device functions can accomplish a much wider range of application scenarios, which will be limited only by your imagination!
 
−
 
−
==='''Advanced SMS capabilities'''===
 
−
 
−
Teltonika devices have a broad SMS usage spectrum including advanced device configuration and debugging. A full list of SMS commands can be found [[FMB SMS/GPRS Commands|'''here.''']]
 
−
 
−
For example, one of the most widely used SMS command for configuring the device is "setparam". Below you can see a description of this command:
 
−
 
−
Setparam changes parameter value. Command structure is: ''"<SMS_Login><Space><SMS_Password><Space>setparam<Space>[Parameter ID]'' ''':''' ''[New Parameter Value]'' ''';''' ''[Parameter ID]'' ''':''' ''[New Parameter Value]''..." Parameter ID consists of 3 or 5 digits. A detailed list of parameters and identifiers can be found [[FMB Device Family Parameter list|'''here.''']]
 
−
{| class="wikitable"
 
−
|+
 
−
|[[File:WIKI_hover.gif]]
 
−
|You can also find parameter ID by hovering the mouse pointer over specific parameter in the configurator.
 
−
|}
 
−
SMS command is limited to 160 characters.
 
−
 
−
Example:
 
−
 
−
"setparam 101:1" will change ignition setting to "DIN1".
 
−
 
−
Answer:
 
−
 
−
"Param ID:101 Value:1"
 
−
 
−
Example:
 
−
 
−
"setparam 101:2;138:1" will change ignition setting to "Accelerometer" and movement source to "Ignition"
 
−
 
−
==='''Advanced Use Case configuration'''===
 
−
 
−
Our devices can be as simple or as complicated as you want them to be. Having one firmware and one configurator for all the devices allows different devices to be used in a broad spectrum of use cases. Other use cases have specific devices assigned.
 
−
 
−
To show how easy it is to use our devices in different use cases we prepared a technical description of what steps are needed to integrate our device into your use case.
 
−
 
−
Each category explains what parameters have to be configured and why as well as showing examples of what information you should expect on your server and how to read it.
 
−
 
−
'''General''' use case descriptions, an overview of the most commonly used solutions, their topologies, and possibilities, provided on the Teltonika website '''[https://teltonika-gps.com/industries/use-cases/ USE CASES]'''.
 
−
 
−
'''Specific technical''' use case instructions can be found [[Usage scenarios|'''here.''']]
 
−
 
−
=='''<big>Solutions</big>'''==
 
−
 
−
[[File:Extend device's capabilities with our solutions banner.png]]
 
−
 
−
In this section, we will get acquainted with our most useful and simple to utilize solutions which will provide remote access, management, and control of your device as well as external devices like tachograph.
 
−
 
−
==='''FOTA WEB'''===
 
−
 
−
FOTA WEB – a brand new and exciting solution for remote access to your Teltonika Fleet management devices! FOTA WEB enables firmware upgrades, configuration changes, remote device debugging of FMx devices, as well as CAN adapter updates without a need of a dedicated application – everything is achieved through your regular Web browser, from any device. By default, the device connects to FOTA WEB every 720 minutes (parameter is configurable). For more information click '''[[FOTA WEB|here.]]''' If you would like to have your own FOTA WEB account, please contact your Sales Manager. [https://www.youtube.com/watch?v=SiMwnkEEes4 '''Short video about FOTA WEB.''']
 
−
 
−
Moreover, we also have a desktop FOTA solution: desktop ''FOTA is the predecessor of FOTA WEB, which is mainly used for updating EOL (End-Of-Life, - FM5300, FMA120, etc.) devices. We strongly advise to use our newest [[FOTA WEB|'''FOTA WEB''']] platform for OTA changes.''
 
−
 
−
'''''Note:''''' FOTA WEB meets all '''GDPR''' requirements thus '''we do not store, track or analyze your personal data.'''
 
−
 
−
==='''WEB Tacho'''===
 
−
 
−
Teltonika WEB Tacho is an online service that allows to remotely download Tachograph files from supported tachographs, using Teltonika professional trackers. Files are stored on server, in defined format (.DDD, .V1B, .C1B, .TGD). Files can be downloaded – directly from the website, receive in Email, receive to a defined FTP server. For more information click '''[[WEB Tacho|here.]]''' If you would like to have your own WEB Tacho account, please contact your Sales Manager.
 
−
 
−
=='''<big>Protocols</big>'''==
 
−
 
−
[[File:Understand communication language banner.png]]
 
−
 
−
Our devices communicate using unique Teltonika's protocols. Protocols are applied for different usage scenarios using Codecs. Each Codec has its own structure and application scenario. A codec is a device or computer program for encoding or decoding a digital data stream or signal.
 
−
 
−
==='''Data sending protocols'''===
 
−
 
−
Each Codec used by Teltonika devices has a different purpose. For example, [[Codec#Codec 8 Extended|'''Codec 8 Extended''']] is main FM device protocol used to send data to server, while [[Codec#Codec for communication over GPRS messages|'''Codec 12''']] is used for device-server communication using GPRS messages. All information about Teltonika's communication protocols used by FM devices can be found [[Codec|'''here.''']]
 
−
 
−
==='''Protocols implementation'''===
 
−
 
−
TCP/UDP listener and AVL Records parser, which source code could be used as a template for developing your own server, can be helpful for implementing protocols. A full software pack can be downloaded from [[Special:Redirect/file/Protocols_and_AVL_parser_pack.zip|'''here.''']] Archive password: 1234.
 
−
 
−
 
−
Each device I/O parameter has its own unique ID, which is called AVL ID. Once the TCP/UDP listener and AVL Records parser are implemented, received AVL IDs descriptions can be checked in the AVL ID list page for your specific device (for example: [[FMB120_Teltonika_Data_Sending_Parameters_ID|'''FMB120''']] ).
 
−
 
−
[[Category:General Information]]
 

Revision as of 13:59, 25 March 2021

Main Page > General Information > Universal Device Test Guide
Qsg rut950 teltonika.PNG

How to insert SIM card and connect the battery*

  1. Gently remove device cover using plastic pry tool from both sides as it is showed in a 1st picture.
  2. Insert SIM card as shown with PIN request disabled or read Security info how to enter it later in Configurator. Make sure that SIM card cut-off corner is pointing forward to slot.
  3. Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
  4. Attach device cover back. Device is ready to be connected.



FMB1 cover1 correct.pngFMB1 cover2 correct.pngFMB1 cover3 correct.pngFMB1 cover4 correct.png



* If you would like to check how to insert SIM card into your particular device, you will find a link with all devices manuals here.

Alert.png
 SIM card insertion/removal must be performed when device is powered off – external voltage and internal battery disconnected. Otherwise SIM card might be damaged or device will not detect it.

PC Connection (Windows)

Power-up device with DC voltage (10 – 30 V)* power supply using supplied power cable. LED’s should start blinking, see “LED behaviour description”.

  1. Connect device to computer using USB cable or Bluetooth connection:
    • Using USB cable
    • Using Bluetooth
      • Device Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named – “FMxyzw_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done. Keep in mind that the FMx640 devices do not support configuration via Bluetooth.
  2. You are now ready to use the device on your computer.


* FMB900, FMB910, FMB920, MTB100, FMB202, FMB204 devices support (6 - 30 V) DC power supply.

How to install USB drivers (Windows)

  1. Please download COM port drivers from Teltonika here.
  2. Extract and run TeltonikaCOMDriver.exe.
  3. Click Next in driver installation window.
  4. In the following window click Install button.
  5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

Configuration (Windows)

At first device will have default factory settings set. These settings should be changed according to the user's needs.
Main configuration can be performed via Teltonika Configurator software. Get the latest Configurator version from here. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS .NET requirements
Operating system MS .NET Framework version Version Link
  • Windows Vista
  • Windows 7
  • Windows 8.1
  • Windows 10
 MS .NET Framework 4.6.2 32 and 64 bit www.microsoft.com

Launch Configurator.exe. After launch software language can be changed by clicking Language icon.png in the right bottom corner:

FMB Configurator language.jpg

Configuration process begins by pressing on connected device:

Faceless configurator select.png

After connection to Configurator Status window will be displayed:

Faceless configurator.png

Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. FMB1YX can be loaded and saved to the device. After any modification of configuration changes need to be saved to device using Save to device button. Main buttons offer following functionalities:

  1. Load from device.png Load from device – loads configuration from device.
  2. Save to device.png Save to device – saves configuration to device.
  3. Load from file.png Load from file – loads configuration from file.
  4. Save to file.png Save to file – saves configuration to file.
  5. Firmware update.png Update firmware – updates firmware on device.
  6. Read records.png Read records – read records from device.
  7. Reboot device.png Reboot device – restarts device.
  8. Reset configuration.png Reset configuration – sets device configuration to default.

Most important configurator sections are GPRS – where all your server and GPRS settings can be configured and Data Acquisition – where data acquiring parameters can be configured. More details about devices configuration using Configurator and more information about your particular device can be found in the manual.

Quick SMS configuration

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it: 

"  setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"

GPRS settings:

  • 2001 – APN
  • 2002 – APN username (if there are no APN username, empty field should be left)
  • 2003 – APN password (if there are no APN password, empty field should be left)

Server settings:

  • 2004 – Domain
  • 2005 – Port
  • 2006 – Data sending protocol (0 – TCP, 1 – UDP)

Note: Before SMS text, two space symbols should be inserted.

IOS sms cfg.png
Default configuration settings
Movement and ignition detection:
Accelerometer.png Vehicle movement will be detected by accelerometer Ignition detection-2-2.png Ignition will be detected by vehicle power voltage between 13,2 – 30 V
Device makes a record On Moving if one of these events happen:
300s icon 2.png 300 seconds passes Angle 10 2.png Vehicle turns 10° degrees
Min distance.png Vehicle drives 100 meters Speed delta.png Speed difference between last coordinate and current position is greater than 10 km/h
Device makes a record On Stop if:
1h icon.png 1 hour passes while vehicle is stationary and ignition is off
Records sending to server:
120 s.png If device has made a record it is sent to the server every 120 seconds


After successful SMS configuration, device will synchronize time and update records to configured server. More SMS commands can be found here.

Mounting recommendations

  • Connecting wires
    • Wires should be connected while the module is not plugged in.
  • Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
  • There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.
  • If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.
  • Wires cannot be connected to the board computers or control units.


  • Connecting power source
    • Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.
    • When module is connected, measure voltage again to make sure it did not decrease.
    • It is recommended to connect to the main power cable in the fuse box.
    • 3 A, 125 V external fuse shall be used.


  • Connecting ignition wire
    • Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
    • Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
    • Check if power is still available when you turn off any of vehicles devices.
    • Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.


  • Connecting ground wire
    • Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
    • If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
    • For better contact scrub paint from the spot where loop is going to be connected.


Alert.png
 PAY ATTENTION! Connecting the power supply must be carried out in a very low impedance point of on-board vehicle network. These points in the car are the battery terminals. Therefore, we recommend connecting the power of device (GND and POWER wires) directly to the battery terminals. Another valid option is to connect the wires to the main POWER cable inside the fuse box (if there is none, then to the power supply where the fuses of vehicle’s computer are), GND wire must be connected in a special point, designed to connect GND vehicle computer. Connecting the GND at an arbitrary point to the mass of the car is unacceptable, as static and dynamic potentials on the line GND will be unpredictable, which can lead to unstable device operation and even its failure.


Installation instructions

In case device has internal GNSS antenna it should be mounted with the logo facing towards open sky (metal free)

Faceless device.jpg


Device can be mounted under the plastic panel behind the front window, with the sticker direction to a window (sky). It is recommended to place device behind dashboard as close to the window as possible. A good example of GNSS antenna placement is displayed in a picture below (area colored green).

SIM card should be inserted in the module while the connector is plugged off (while module has no power).

FMB120 install2.jpg

Safety information

Precautions

This message contains information on how to operate device safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

  • The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10..+30V DC.
  • To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
  • Before unmounting the device from the vehicle, ignition MUST be OFF.
  • When connecting the wires2x6 connector wires to the vehicleconnection (1x5) cables to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.
  • When installing the connection cables to the vehicle, the appropriate jumpers of the power supply of the vehicle should be disconnected.
  • Before unmounting the device from the vehicle, the 2x6 connector 1x5 connection must be disconnected.
  • The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.
  • The devices are not designed as a navigational device for boats.


Bw nb.png Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
Bw nb.png All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
Bw key.png The device must be connected only by qualified personnel.
Bw tick.png The device must be firmly fastened in a predefined location.
Bw tick.png The programming must be performed using a PC with autonomic power supply.
Bw humidity.png The device is susceptible to water and humidity.
Bw ecute.png Installation and/or handling during a lightning storm is prohibited.
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Universal_Device_Test_Guide&oldid=63926"