Difference between revisions of "Wialon+ADAS solution"
MindaugasK (talk | contribs) |
MindaugasK (talk | contribs) |
||
(10 intermediate revisions by 2 users not shown) | |||
Line 3: | Line 3: | ||
== ADAS on Wialon platform == | == ADAS on Wialon platform == | ||
− | Our devices are supported by many third-party platforms however, currently only one platform, Wialon supports our advanced driver safety system [https://wiki.teltonika-gps.com/view/ADAS ADAS] | + | Our devices are supported by many third-party platforms however, currently only one platform, Wialon supports our advanced driver safety system [https://wiki.teltonika-gps.com/view/ADAS ADAS] |
− | |||
In this chapter, we will show you how to configure the device and also how to configure the Wialon platform for receiving information from ADAS. | In this chapter, we will show you how to configure the device and also how to configure the Wialon platform for receiving information from ADAS. | ||
Line 19: | Line 18: | ||
To do that please go to Teltonika configurator window and press '''Ctrl+Alt+I''' on your keyboard. | To do that please go to Teltonika configurator window and press '''Ctrl+Alt+I''' on your keyboard. | ||
− | Copy the key | + | Copy the key ( '''jXIEpOLMg6bIyPDZdpIpKgSVCTVdvLyNEua76CNP2TQAAADTTaD1uQ/FhdhfRCCi7PRdtlSutkbDlC9c1UejUWUUSo5bwNhCHG5NGCdn8Qh/DhVppOsbSfH/9Y+8SjUHbqvVNBlKZw9LTIT4nveAKc3ODwy7aumxvQoZEynV9+B44ucUIzDJk9WLVfQfjr54+4O747drg4m/HxoTFGoGg0GuLi7UKFsERiVClqT+b2Qh30L3hBgwgwqxjoUABAAAAAAACIsf''' ) |
− | |||
− | '''jXIEpOLMg6bIyPDZdpIpKgSVCTVdvLyNEua76CNP2TQAAADTTaD1uQ/ | ||
− | |||
− | |||
− | |||
− | |||
− | |||
to “New key” section and press Register. If everything is OK, you will see new device added on the left side. | to “New key” section and press Register. If everything is OK, you will see new device added on the left side. | ||
After that you can use ADAS on FMX640 | After that you can use ADAS on FMX640 | ||
Line 81: | Line 73: | ||
'''Note:''' You must enter device IMEI in "Unique ID" to identify device in Wialon platform. | '''Note:''' You must enter device IMEI in "Unique ID" to identify device in Wialon platform. | ||
− | [[File: | + | [[File:Wialon_add_adas.gif]] |
'''Step 2''' | '''Step 2''' | ||
− | + | Set the command to request a photo. | |
− | Go to | + | Go to Units tab and push on "wrench" icon. |
Now select "Commands" and press new. | Now select "Commands" and press new. | ||
Line 97: | Line 89: | ||
After that press ok and the command will appear. | After that press ok and the command will appear. | ||
− | [[File: | + | [[File:Command set.gif]] |
'''Step 3''' | '''Step 3''' | ||
− | After the command was created, you should to go to the "Monitoring" tab, select needed device and press the arrow and select GPRS command. | + | After the command was created, you should to go to the "Monitoring" tab, select needed device and press the arrow and select GPRS. |
+ | |||
+ | After that select from which camera you need to get front-rear photo and press ok. | ||
+ | |||
+ | After you will see new window opened and command was sent, you will see that new picture arrived from the rear camera and then from the front. | ||
+ | |||
+ | [[File:Photo ask.gif]] | ||
+ | |||
+ | '''Step 4''' | ||
+ | |||
+ | Video request set up. | ||
+ | |||
+ | First open unit properties. | ||
+ | |||
+ | Than, go to the "Video" section, select "Set cameras", choose Cam 1 Cam 2 and pres ok twice. | ||
+ | |||
+ | [[File:Video settings.gif]] | ||
+ | |||
+ | '''Step 5''' | ||
+ | |||
+ | To request a video go to the "Video" section, select "Playback", select "save requested file to Files", select "Unit". After setting date and time of the video you need, press "Request". Wialon will generate a message and show the files in the "Files" section. Finally, it will be sent to Wialon. | ||
+ | |||
+ | '''Note:''' We recommend creating a notification with the same time intervals and no more than +/-15 sec. The video file duration can be max 30 sec (according device limitation). | ||
+ | |||
+ | [[File:Video requrest.gif]] | ||
+ | |||
+ | '''Step 6''' | ||
+ | |||
+ | If you need to set a video request from using trigger, it should be done from Wialon side. | ||
+ | |||
+ | Go to "Notification" tab, select "New", select "Device", and here choose required triggers. | ||
− | + | In GIF below, you can see an example of the trigger set on Digital Input. After configuring the command and selecting "ok", command will appear and if Digital Input will be triggered you will receive video. | |
− | [[File: | + | [[File:Video triggered.gif]] |
Revision as of 12:12, 7 July 2022
ADAS on Wialon platform
Our devices are supported by many third-party platforms however, currently only one platform, Wialon supports our advanced driver safety system ADAS In this chapter, we will show you how to configure the device and also how to configure the Wialon platform for receiving information from ADAS.
Configurator set-up instructions for Spec ID on FMX640
It is important to note that ONLY specific ADAS cameras starting with the Serial Number S/N: 9C can be connected and used with FMX640 devices. Cameras starting with different S/N numbers for example; 9B, are currently not supported.
Base firmware version of the device will not have the ability to connect ADAS through RS235 connection, it has to be activated using special(spec) firmware. If you want to remove spec ID, you need to install FMX64.Ver.01.02.10.Rev.103_ID1 firmware, after that you can install spec ID1039 firmware.
To use firmware FMX64.Ver.01.02.10.Rev.103_ID1039 which has spec ID a spec key is required to be inserted into the configurator Teltonika.Configurator_1.7.40_B.FM64_R.55
To do that please go to Teltonika configurator window and press Ctrl+Alt+I on your keyboard.
Copy the key ( jXIEpOLMg6bIyPDZdpIpKgSVCTVdvLyNEua76CNP2TQAAADTTaD1uQ/FhdhfRCCi7PRdtlSutkbDlC9c1UejUWUUSo5bwNhCHG5NGCdn8Qh/DhVppOsbSfH/9Y+8SjUHbqvVNBlKZw9LTIT4nveAKc3ODwy7aumxvQoZEynV9+B44ucUIzDJk9WLVfQfjr54+4O747drg4m/HxoTFGoGg0GuLi7UKFsERiVClqT+b2Qh30L3hBgwgwqxjoUABAAAAAAACIsf ) to “New key” section and press Register. If everything is OK, you will see new device added on the left side. After that you can use ADAS on FMX640
Device configuration
Step 1
Enable codec 8 extended.
Step 2
Configure Domain and Port for the device to send data to the Wialon. This information you will find then you register the device in Wialon
Step 3
Go to RS232/RS485 and enable ADAS in order for the configurator to open additional settings.
Configure the ADAS image sending and camera settings for your needs in the ADAS window which opens after selecting ADAS in RS232 input.
Step 4
Go to I/O element and select required or desired parameter priority to Low.
Step 5
ADAS server settings will be different:
Domain: Will be the same as from Wialon for the device
Port: 22297
Wialon configuration
Step 1
Login into Wialon and go to the Units and select New.
Configure the device and activate ADAS device according to the GIF.
Note: You must enter device IMEI in "Unique ID" to identify device in Wialon platform.
Step 2
Set the command to request a photo.
Go to Units tab and push on "wrench" icon.
Now select "Commands" and press new.
Then you should press "New" button to call out new window.
You'll need to create the name of the command and select the command type according to the GIF.
After that press ok and the command will appear.
Step 3
After the command was created, you should to go to the "Monitoring" tab, select needed device and press the arrow and select GPRS.
After that select from which camera you need to get front-rear photo and press ok.
After you will see new window opened and command was sent, you will see that new picture arrived from the rear camera and then from the front.
Step 4
Video request set up.
First open unit properties.
Than, go to the "Video" section, select "Set cameras", choose Cam 1 Cam 2 and pres ok twice.
Step 5
To request a video go to the "Video" section, select "Playback", select "save requested file to Files", select "Unit". After setting date and time of the video you need, press "Request". Wialon will generate a message and show the files in the "Files" section. Finally, it will be sent to Wialon.
Note: We recommend creating a notification with the same time intervals and no more than +/-15 sec. The video file duration can be max 30 sec (according device limitation).
Step 6
If you need to set a video request from using trigger, it should be done from Wialon side.
Go to "Notification" tab, select "New", select "Device", and here choose required triggers.
In GIF below, you can see an example of the trigger set on Digital Input. After configuring the command and selecting "ok", command will appear and if Digital Input will be triggered you will receive video.