Difference between revisions of "Template:FMT1 Mounting recommendations"
From Wiki Knowledge Base | Teltonika GPS
Simkunas.ma (talk | contribs) |
|||
(16 intermediate revisions by 5 users not shown) | |||
Line 1: | Line 1: | ||
− | + | =='''Mounting recommendations'''== | |
− | + | [[Image:FMT100_mounting_tape-1.png|500px|right|thumb|Double sided tape on the back]][[Image:FMT100_mounting_tampo-2.png|500px|right|thumb|Example of device mounting]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | Device fastening | |
− | + | * Locate the battery in your vehicle. If present remove the battery cover to access the battery. | |
− | * | + | * Wipe clean the installation surface of the battery if any dust or dirt is visable. |
− | * | + | * There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna and LEDs indicators are facing up. |
− | * | ||
− | |||
− | |||
− | + | Connecting power wire | |
− | + | * Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery. | |
− | * | ||
− | |||
− | |||
− | |||
− | |||
− | < | + | Connecting ground wire |
− | < | + | * Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery. |
− | * | + | <br /> |
− | * | + | <br /> |
− | * | + | <br /> |
− | + | <br /> | |
+ | <br /> | ||
+ | <br /> | ||
+ | <br /> | ||
+ | <br /> | ||
+ | <br /> | ||
+ | <br /> | ||
+ | <br /> | ||
+ | <br /> | ||
+ | =='''Safety information'''== | ||
+ | This message contains information on how to operate {{{model|FMT100}}} safely. By following these requirements and recommendations, you will avoid any dangerous situations. You must read these instructions carefully and follow them strictly before operating the device! | ||
+ | *The device uses a 10 V...30 V DC power supply. The nominal voltage is 12 V DC. The allowed range of voltage is 10 V...30 V DC. | ||
+ | *To avoid mechanical damage, it is advised to transport the device in an impact-proof package. | ||
+ | *Before dismounting the device from the vehicle, ignition '''MUST be OFF'''. | ||
− | + | {| class="wikitable" style="width:100%; background: white; border-bottom: 2px solid #0054A6;" | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | {| class="wikitable" style="border- | ||
|+ | |+ | ||
|- | |- | ||
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_nb.png|50px]] |
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.''' |
+ | |- | ||
+ | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_nb.png|50px]] | ||
+ | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''All wireless data transferring devices produce interference that may affect other devices which are placed nearby.''' | ||
+ | |- | ||
+ | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_key.png|50px]] | ||
+ | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''The device must be connected only by qualified personnel.''' | ||
+ | |- | ||
+ | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_tick.png|50px]] | ||
+ | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''The device must be firmly fastened in a predefined location.''' | ||
|- | |- | ||
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_tick.png|50px]] |
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''The programming must be performed using a PC with autonomic power supply.''' |
|- | |- | ||
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_humidity.png|50px]] |
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''The device is susceptible to water and humidity if the device housing is not properly closed.''' |
|- | |- | ||
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_ecute.png|50px]] |
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''Installation and/or handling during a lightning storm is prohibited.''' |
|- | |- | ||
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_nb.png|50px]] |
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''Teltonika is not responsible for any harm caused by wrong cables used for connection between PC and {{{model|FMT100}}}''' |
|- | |- | ||
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_nb.png|50px]] |
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''Risk of explosion if battery is replaced by an incorrect type.''' |
|- | |- | ||
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | [[Image:Bw_disposal.png|50px]] |
− | | style="text-align: left; | + | | style="text-align: left; border: 1px solid white; border-bottom: 2px solid #E8E8E8;" | '''Battery should not be disposed of with general household waste. Bring damaged or worn-out batteries to your local recycling center or dispose them to battery recycle bin found in stores.''' |
|} | |} | ||
− |
Latest revision as of 14:10, 29 August 2023
Mounting recommendations
Device fastening
- Locate the battery in your vehicle. If present remove the battery cover to access the battery.
- Wipe clean the installation surface of the battery if any dust or dirt is visable.
- There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna and LEDs indicators are facing up.
Connecting power wire
- Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.
Connecting ground wire
- Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.
Safety information
This message contains information on how to operate FMT100 safely. By following these requirements and recommendations, you will avoid any dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!
- The device uses a 10 V...30 V DC power supply. The nominal voltage is 12 V DC. The allowed range of voltage is 10 V...30 V DC.
- To avoid mechanical damage, it is advised to transport the device in an impact-proof package.
- Before dismounting the device from the vehicle, ignition MUST be OFF.