Difference between revisions of "NBL-2"

From Wiki Knowledge Base | Teltonika GPS
m
m (Text replacement - "Bluetooth(?!®)" to "Bluetooth®")
 
(20 intermediate revisions by 2 users not shown)
Line 4: Line 4:
 
'''Description:'''
 
'''Description:'''
  
−
Netronix NBL-2 -  wireless RFID reader with Bluetooth.
+
Netronix NBL-2 -  wireless Bluetooth® RFID reader with additional buttons.
  
 
'''NBL-2 is great in these use cases:'''
 
'''NBL-2 is great in these use cases:'''
−
* Authorized driving - keep track of who is driving your vehicle according to the NBL-2 ID they use to authenticate themselves.
+
* Authorized driving - track who is driving your vehicle. You will receive a card ID every time a driver applies a card to NBL-2 reader.
−
* Private mode – gives ability to mask all the personal data while vehicle is used in Private mode.
+
* Private mode – this solution will allow your company car to be used by employees for personal purposes without violating the EU General Data Protection Regulations by masking all the personal data while vehicle is used in Private mode. Moreover, self-employed people can easily convert their own car into a business asset and ensure that the data provided (Example - distance traveled) is correct and shown only working hours' driven distance. Private/business mode can be easily switched by any of the NBL-2 buttons.
  
  
−
'''Functionality:'''
+
'''Futures:'''
  
−
* Unpaired reader (state after default reset) is waiting for button only
+
* Mifare® Classic, Desfire card supports
−
* Reader scans for transponder detect or button press all time when is paired
+
* Bluetooth® low energy module
−
* In case above event occurs, reader sends advertising packet for Ta time in period Tb. Defaults: Ta=50sec, Tb=100ms
+
* Operating frequency - 13,56MHz
−
* During advertising green led is flashing slowly. Reader stops blinking and advertising after disconnection.
+
* Built in two LED indicators
−
* Depending on configuration, read card ID can be present on advertising packet or/and on characteristic
+
* Built in two buttons
−
* Reader close connection and goes into low power 50 seconds after last data exchange.
+
* UID and card DATA available
−
* Each LED can be controlled on GATT services
+
* Configure via BL link
−
* Reader can be on/off by long button press
+
* Firmware update via Bluetooth®
−
* Reader perform sensor measurement in period which is configurable
 
−
* Button reacts immediately
 
−
* Sensors configuration is set by GATT services.
 
−
* Detecting the start and stopping the vehicle. This mode is active immediately after turn on the device.<br />
 
 
==Product Specification==
 
==Product Specification==
 
{| class="wikitable"
 
{| class="wikitable"
−
|Operating frequency
 
−
|13,56MHz
 
−
|-
 
−
|Supported standards
 
−
|MIFARE® Classic
 
−
MIFARE® DESFire
 
−
|-
 
−
|Interface
 
−
|Bluetooth
 
 
|-
 
|-
 
|Supply voltage
 
|Supply voltage
Line 49: Line 36:
 
|Size (mm)
 
|Size (mm)
 
|58 x 99 x 19
 
|58 x 99 x 19
 +
|-
 +
|Weight
 +
|43.78 g
 
|-
 
|-
 
|Type
 
|Type
Line 54: Line 44:
 
|}
 
|}
  
−
==NBL-2 configuration==
+
==NBL-2 Configuration==
 +
 
 +
'''For the NBL Tools application, contact the Netronix NBL manufacturer.''' 
 +
 
 +
First, you have to make sure that NBL-2 firmware version is updated to 1.3.
 +
 
 +
If the firmware version is lower than 1.3, it is necessary to update the device.
  
  
 
'''1.    Updating NBL-2'''
 
'''1.    Updating NBL-2'''
  
−
First, you have to make sure that NBL-2 firmware version is updated to 1.3. Go to NBL Tools application -> Device -> Characteristic -> Device Information Service -> Firmware Revision String.
+
Go to NBL Tools application -> Device -> Characteristic -> Device Information Service -> Firmware Revision String.
  
 
[[File:NBL_conf1.jpg.jpg|alt=|frameless|520x520px]]  [[File:NBL_conf2.jpg.jpg|alt=|border|frameless|520x520px]]  [[File:NBL_conf3.jpg.jpg|alt=|frameless|519x519px]]
 
[[File:NBL_conf1.jpg.jpg|alt=|frameless|520x520px]]  [[File:NBL_conf2.jpg.jpg|alt=|border|frameless|520x520px]]  [[File:NBL_conf3.jpg.jpg|alt=|frameless|519x519px]]
Line 69: Line 65:
 
If it is 1.2, then update NBL-2 according to these steps:
 
If it is 1.2, then update NBL-2 according to these steps:
  
−
1.      Run NBL Tools application
+
1.      Run the NBL Tools application
  
−
2.      Update the firmware database (tap: Menager Firmware -> Update the database -> Start). Select NBL-2 and check 1.3 firmware version.
+
2.      Update the firmware database (tap: Manager Firmware -> Update the database -> Start). Select NBL-2 and check 1.3 firmware version.
  
 
[[File:NBL conf4.jpg.jpg|frameless|519x519px]]  [[File:NBL conf5.jpg.jpg|frameless|519x519px]]  [[File:NBL conf6.jpg.jpg|frameless|519x519px]]
 
[[File:NBL conf4.jpg.jpg|frameless|519x519px]]  [[File:NBL conf5.jpg.jpg|frameless|519x519px]]  [[File:NBL conf6.jpg.jpg|frameless|519x519px]]
  
−
3.      Back to main menu.
+
3.      Back to the main menu.
  
−
4.      Tap Device option.
+
4.      Tap the Device option.
  
 
[[File:NBL conf7.jpg.jpg|frameless|520x520px]]
 
[[File:NBL conf7.jpg.jpg|frameless|520x520px]]
  
−
5.      Wake up the device - eg entering it into the bootloader mode.
+
5.      Wake up the device - for example, by applying a card to it.
  
−
6.      Select the device from the list (long press), then select Update firmware from the drop-down menu and press Start button.
+
6.      Select the device from the list, then select Update firmware from the drop-down menu and press the Start button.
  
 
[[File:NBL conf9.jpg.jpg|frameless|520x520px]]  [[File:NBL conf8.jpg.jpg|frameless|519x519px]]
 
[[File:NBL conf9.jpg.jpg|frameless|520x520px]]  [[File:NBL conf8.jpg.jpg|frameless|519x519px]]
  
 
7.      Correct firmware update will be signaled by device start-up led message.
 
7.      Correct firmware update will be signaled by device start-up led message.
 +
 +
'''2.    Power OFF /Reset to default settings'''
 +
 +
To set factory defaults and unpairing both buttons must be pressed for 5 seconds additionally button 1 (blue) must be pressed first. It is also factory/transport configuration.
 +
 +
Procedure:
 +
# Press Button1 and hold
 +
# Press Button2 and hold
 +
# Keep the buttons pressed for 5 seconds
 +
# The return to the factory settings will be signaledby flashing LED1 and LED2
 +
 +
 +
'''3.    Power ON (After Powered OFF)'''
 +
 +
Procedure:
 +
# Press Button 2 and hold
 +
# Keep the button pressed for 5 seconds
 +
# The Power On will be signaled by flashing LED1 and LED2
 +
 +
 +
'''4.    Paring'''
 +
 +
When device have defaults settings, reader waits for button then sends advertising packet for 50 seconds and blinks LEDs. First connection in this state is pairing process. Paring mode used: No Pin.
 +
 +
When the device is paired, the pairing mode is changed to pairing using the PIN. This prevents the pairing of additional devices
 +
 
==Device configuration==
 
==Device configuration==
−
Setting up NBL-2 device to connect with FMB device. Go to Teltonika configurator -> Bluetooth 4.0 and set it up like it shown in this screenshot (MAC adress will depend on your particular NBL sensor):
+
This functionality is available from firmware version FMB.Ver.03.28.05.Rev.04
 +
 
 +
Setting up NBL-2 device to connect with FMB device.  
 +
 
 +
Go to Teltonika configurator -> Bluetooth® 4.0 and set it up like it shown in this screenshot (MAC address will depend on your particular NBL sensor):
  
 
[[File:Nbl2 1.png|frameless|660x660px]]
 
[[File:Nbl2 1.png|frameless|660x660px]]
Line 99: Line 125:
 
Then go to I/O settings:  
 
Then go to I/O settings:  
  
−
Make sure to enable BLE RFID #1 parameter (ID: 51740) and set operand to „On Change“.
+
Make sure to enable the BLE RFID #1 parameter (ID: 51740). We would recommend to set the operand to „[[Template:FMB I/O settings#Operand On Change|On Change]]“.
  
 
[[File:Nbl2 3.png|frameless|999x999px]]
 
[[File:Nbl2 3.png|frameless|999x999px]]
  
 
==Setting up Private/Business mode==
 
==Setting up Private/Business mode==
−
Make sure to enable Private/Business mode in Trip/Odometer settings. It can be done using SMS commands or configurator. Not every device has these parameters visible in the configurator, therefore they should be configured via SMS commands. It can be done by sending  ''setparam'' SMS (how to send SMS commands: [[FMB120 SMS/GPRS Commands|https://wiki.teltonika-gps.com/view/FMB120_SMS/GPRS_Commands]]). Set it to High or Low priority (parameter ID: 11850). Enable triggers as NBL-1 Button1 or NBL-1 Button2 (parameter ID: 11811).
+
Make sure to enable Private/Business mode in Trip/Odometer settings. It can be done using SMS commands or a configurator. Not every device has these parameters visible in the configurator, therefore they should be configured via SMS commands. It can be done by sending  ''setparam'' SMS (how to send SMS commands: [[FMB120 SMS/GPRS Commands|https://wiki.teltonika-gps.com/view/FMB120_SMS/GPRS_Commands]]). Set it to High or Low priority (parameter ID: 11850). Enable triggers as NBL-1 Button1 or NBL-1 Button2 (parameter ID: 11811).
  
 
[[File:NBL_conf12.jpg.png|alt=|frameless|500x500px]]
 
[[File:NBL_conf12.jpg.png|alt=|frameless|500x500px]]
Line 113: Line 139:
  
  
−
Don‘t forget to save all these changes to device and you are ready to test NBL-2 sensor.
+
Don‘t forget to save all these changes to the device and you are ready to test the NBL-2 sensor.
  
 
[[Private/Business Driving Mode Functionality|More information about Private/Business Driving Mode Functionality.]]
 
[[Private/Business Driving Mode Functionality|More information about Private/Business Driving Mode Functionality.]]
  
 
==Testing NBL-2==
 
==Testing NBL-2==
−
Power up FMB device and start logging it in Terminal application. When RFID card is not enabled, BLE RFID #1 parameter (AVL ID: 451) will show a specific value. Example:
+
'''1.    Using the Configurator'''
 +
 
 +
Power up the FMB device, connect it to PC and open Configurator application. Configure devices as shown above.
 +
 
 +
When the RFID card is not enabled, the BLE RFID #1 parameter (AVL ID: 451) will show a specific value.
 +
 
 +
Example (Status tab => I/O Info):
 +
 
 +
[[File:NBL-2 cfg1.png|frameless|900x900px]]
 +
 
 +
When the RFID card is activated (card touched to NBL-2 and followed by two beeps) BLE RFID #1 parameter should look like this:
 +
 
 +
[[File:NBL-2 cfg2.png|frameless|900x900px]]
 +
 
 +
 
 +
'''2.    Using the Terminal application'''
 +
 
 +
Power up the FMB device, connect it to PC and start logging it into the Terminal application.  
 +
 
 +
When the RFID card is not enabled, the BLE RFID #1 parameter (AVL ID: 451) will show a specific value.  
 +
 
 +
Example:
  
 
''IO ID[451]: 0x0000000000000000''
 
''IO ID[451]: 0x0000000000000000''
  
−
When RFID card is activated (card touched to NBL-2 and followed by two beeps) BLE RFID #1 parameter should look like this:
+
When the RFID card is activated (card touched to NBL-2 and followed by two beeps) BLE RFID #1 parameter should look like this:
  
 
''IO ID[451]: 0x0004193EF2576680''
 
''IO ID[451]: 0x0004193EF2576680''
Line 135: Line 182:
 
''IO ID[391]: 1''
 
''IO ID[391]: 1''
 
==NBL-2 packet==
 
==NBL-2 packet==
−
NBL-T data is being read via broadcast packets only. Packet structure is described below:
+
NBL-T data is being read via broadcast packets only. The packet structure is described below:
 +
{| class="wikitable"
 +
|+
 +
!EIR Type
 +
!Description / Value
 +
!LEN
 +
|-
 +
|Flags – 0x01
 +
|0x06
 +
GeneralDiscoverable,
  
−
[[File:NBL conf 13.png|frameless]]
+
BrEdrNotSupported
−
 
+
|3B
−
 
+
|-
−
0x02010606094E424C2D540CFF4E58 A7CB250501B01A0047
+
|Complete name – 0x09
−
 
+
|‘NBL-2’ (for NBL-2 device)
−
'''Table No. 1.''' Parsed broadcast packet
+
|7B
 +
|-
 +
|Service data – 0x16
 +
|Data format
 +
{| class="wikitable"
 +
!BYTE:
 +
!0..1
 +
!2
 +
!3
 +
!4
 +
!5
 +
!6
 +
![7..8]
 +
!9
 +
!10..18
 +
|-
 +
|Field:
 +
|UUID
 +
|Status
 +
|Batt
 +
|X
 +
|Y
 +
|Z
 +
|0
 +
|CID_Len
 +
|CID
 +
|}
 
{| class="wikitable"
 
{| class="wikitable"
−
|'''Type'''
+
!Field
−
|'''HEX Value'''
+
!Description
−
|'''ASCII Value'''
+
|-
−
|'''Description'''
+
|UUID
 +
|‘NX’
 
|-
 
|-
−
|09
+
|Status
−
|4E424C2D540C
+
|Data format:
−
|NBL-T
+
{| class="wikitable"
−
|Complete Local name
+
|+
 +
!MSB
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!
 +
!LSB
 
|-
 
|-
−
|FF
+
|Motion
−
|4E58 A7CB250501B01A 00 47
+
|Card
−
|1.      UUID – 2 bytes
+
|Confirm
 +
|0
 +
|0
 +
|0
 +
|B1
 +
|B2
 +
|}
 +
• '''Motion''' – if 1, sensor detect movement
  
−
2.      RFID Id – 7 bytes
+
• '''Card''' – if 1, the ID is read
  
−
3.      Button status – 1 byte
+
• '''Btn1''' – state of button 1  
  
−
4.      Battery level – 1 byte (%)
+
• '''Btn2''' – state of button 2
−
|Manufacturer data
+
 
 +
 
 +
|-
 +
|Batt
 +
|Battery level in %
 +
|-
 +
|X
 +
|X Axis acceleration
 +
|-
 +
|Y
 +
|Y Axis acceleration
 +
|-
 +
|Z
 +
|Z Axis acceleratio
 +
|-
 +
|CID_Len
 +
|ID length
 +
|-
 +
|CID
 +
|ID card number
 
|}
 
|}
−
 
+
|21B
 +
|}
 +
Total packet length: 31B.
 
[[Category:Accessories]]
 
[[Category:Accessories]]

Latest revision as of 15:26, 28 December 2023

Main Page > Accessories > NBL-2

Introduction to the product

NBL-2 3.png

Description:

Netronix NBL-2 -  wireless Bluetooth® RFID reader with additional buttons.

NBL-2 is great in these use cases:

  • Authorized driving - track who is driving your vehicle. You will receive a card ID every time a driver applies a card to NBL-2 reader.
  • Private mode – this solution will allow your company car to be used by employees for personal purposes without violating the EU General Data Protection Regulations by masking all the personal data while vehicle is used in Private mode. Moreover, self-employed people can easily convert their own car into a business asset and ensure that the data provided (Example - distance traveled) is correct and shown only working hours' driven distance. Private/business mode can be easily switched by any of the NBL-2 buttons.


Futures:

  • Mifare® Classic, Desfire card supports
  • Bluetooth® low energy module
  • Operating frequency - 13,56MHz
  • Built in two LED indicators
  • Built in two buttons
  • UID and card DATA available
  • Configure via BL link
  • Firmware update via Bluetooth®

Product Specification

Supply voltage two AAA batteries
Sensor Accelerometer

Low battery voltage

Operating temperature -20ºC to +70ºC
Size (mm) 58 x 99 x 19
Weight 43.78 g
Type RFID reader

NBL-2 Configuration

For the NBL Tools application, contact the Netronix NBL manufacturer.

First, you have to make sure that NBL-2 firmware version is updated to 1.3.

If the firmware version is lower than 1.3, it is necessary to update the device.


1.    Updating NBL-2

Go to NBL Tools application -> Device -> Characteristic -> Device Information Service -> Firmware Revision String.


Note: If the firmware version is 1.1 or 1.0, it is not possible to update it.

If it is 1.2, then update NBL-2 according to these steps:

1.      Run the NBL Tools application

2.      Update the firmware database (tap: Manager Firmware -> Update the database -> Start). Select NBL-2 and check 1.3 firmware version.

NBL conf4.jpg.jpg NBL conf5.jpg.jpg NBL conf6.jpg.jpg

3.      Back to the main menu.

4.      Tap the Device option.

NBL conf7.jpg.jpg

5.      Wake up the device - for example, by applying a card to it.

6.      Select the device from the list, then select Update firmware from the drop-down menu and press the Start button.

NBL conf9.jpg.jpg NBL conf8.jpg.jpg

7.      Correct firmware update will be signaled by device start-up led message.

2.    Power OFF /Reset to default settings

To set factory defaults and unpairing both buttons must be pressed for 5 seconds additionally button 1 (blue) must be pressed first. It is also factory/transport configuration.

Procedure:

  1. Press Button1 and hold
  2. Press Button2 and hold
  3. Keep the buttons pressed for 5 seconds
  4. The return to the factory settings will be signaledby flashing LED1 and LED2


3.    Power ON (After Powered OFF)

Procedure:

  1. Press Button 2 and hold
  2. Keep the button pressed for 5 seconds
  3. The Power On will be signaled by flashing LED1 and LED2


4.    Paring

When device have defaults settings, reader waits for button then sends advertising packet for 50 seconds and blinks LEDs. First connection in this state is pairing process. Paring mode used: No Pin.

When the device is paired, the pairing mode is changed to pairing using the PIN. This prevents the pairing of additional devices

Device configuration

This functionality is available from firmware version FMB.Ver.03.28.05.Rev.04

Setting up NBL-2 device to connect with FMB device.

Go to Teltonika configurator -> Bluetooth® 4.0 and set it up like it shown in this screenshot (MAC address will depend on your particular NBL sensor):

Nbl2 1.png

Mandatory setting condition: Non Stop Scan

Nbl2 2.png

Then go to I/O settings:

Make sure to enable the BLE RFID #1 parameter (ID: 51740). We would recommend to set the operand to „On Change“.

Nbl2 3.png

Setting up Private/Business mode

Make sure to enable Private/Business mode in Trip/Odometer settings. It can be done using SMS commands or a configurator. Not every device has these parameters visible in the configurator, therefore they should be configured via SMS commands. It can be done by sending  setparam SMS (how to send SMS commands: https://wiki.teltonika-gps.com/view/FMB120_SMS/GPRS_Commands). Set it to High or Low priority (parameter ID: 11850). Enable triggers as NBL-1 Button1 or NBL-1 Button2 (parameter ID: 11811).

Don't forget to set up data masking in Private mode if necessary.

Nbl2 4.png


Don‘t forget to save all these changes to the device and you are ready to test the NBL-2 sensor.

More information about Private/Business Driving Mode Functionality.

Testing NBL-2

1.    Using the Configurator

Power up the FMB device, connect it to PC and open Configurator application. Configure devices as shown above.

When the RFID card is not enabled, the BLE RFID #1 parameter (AVL ID: 451) will show a specific value.

Example (Status tab => I/O Info):

NBL-2 cfg1.png

When the RFID card is activated (card touched to NBL-2 and followed by two beeps) BLE RFID #1 parameter should look like this:

NBL-2 cfg2.png


2.    Using the Terminal application

Power up the FMB device, connect it to PC and start logging it into the Terminal application.

When the RFID card is not enabled, the BLE RFID #1 parameter (AVL ID: 451) will show a specific value.

Example:

IO ID[451]: 0x0000000000000000

When the RFID card is activated (card touched to NBL-2 and followed by two beeps) BLE RFID #1 parameter should look like this:

IO ID[451]: 0x0004193EF2576680


When Private/Business mode is enabled (Button1 or Button2 is pressed):

IO ID[451]: 0x0000000000000000

and

IO ID[391]: 1

NBL-2 packet

NBL-T data is being read via broadcast packets only. The packet structure is described below:

EIR Type Description / Value LEN
Flags – 0x01 0x06

GeneralDiscoverable,

BrEdrNotSupported

3B
Complete name – 0x09 ‘NBL-2’ (for NBL-2 device) 7B
Service data – 0x16 Data format
BYTE: 0..1 2 3 4 5 6 [7..8] 9 10..18
Field: UUID Status Batt X Y Z 0 CID_Len CID
Field Description
UUID ‘NX’
Status Data format:
MSB LSB
Motion Card Confirm 0 0 0 B1 B2

• Motion – if 1, sensor detect movement

• Card – if 1, the ID is read

• Btn1 – state of button 1

• Btn2 – state of button 2


Batt Battery level in %
X X Axis acceleration
Y Y Axis acceleration
Z Z Axis acceleratio
CID_Len ID length
CID ID card number
21B

Total packet length: 31B.

Retrieved from "https://wiki.teltonika-gps.com/index.php?title=NBL-2&oldid=94346"