Difference between revisions of "FTC921 First Start"

From Wiki Knowledge Base | Teltonika GPS
 
(17 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
<b>{{{description|Small and smart tracker}}}</b>
 
<b>{{{description|Small and smart tracker}}}</b>
−
{{{pic|[[Image:FTC921.png|400px|right]]}}}
+
{{{pic|[[Image:FTC921-QJABO-datasheet-2023-09-25.1.png|400px|right]]}}}
 +
<br>
 +
<br>
 
<br>
 
<br>
−
 
 
__TOC__
 
__TOC__
  
 +
=='''KNOW YOUR DEVICE'''==
 +
[[File:FTC921_KNOW_YOUR_DEVICE.png|centre|1000 px]]
  
−
=='''HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY'''==
+
=='''HOW TO INSERT NANO-SIM CARD AND CONNECT THE BATTERY'''==
  
 
{{{with_battery|
 
{{{with_battery|
Line 25: Line 28:
  
 
=='''PC CONNECTION (WINDOWS)'''==
 
=='''PC CONNECTION (WINDOWS)'''==
−
1. Power- up FTC921 with DC voltage (10-90V) power supply using power wires. LEDs should start blinking.
+
# Power- up FTC921 with DC voltage (10-90V) power supply using power wires. LEDs should start blinking, see “'''[[FTC921_LED_behaviour_description|LED behaviour description]]'''”.  
−
 
+
# Connect device to computer using USB Type-C cable and install USB driver, see "[[#How to install USB drivers (Windows)|'''HOW TO INSTALL USB DRIVERS (WINDOWS)''']]".
−
2. Connect device to computer using Micro-USB cable and install USB driver, see “How to install USB drivers (Windows)1”
 
−
 
 
  
 
=='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==
 
=='''HOW TO INSTALL USB DRIVERS (WINDOWS)'''==
−
1. Please download COM port drivers from [https://wiki.teltonika-gps.com/images/d/d0/TeltonikaCOMDriver.zip here].
 
  
−
2. Extract and run TeltonikaCOMDriver.exe.
+
# Please download COM port drivers from '''[[Media:TeltonikaCOMDriver.zip|here]]'''.
−
 
+
# Extract and run '''TeltonikaCOMDriver.exe'''.
−
3. Click Next in driver installation window.
+
# Click '''Next''' in driver installation window.
−
 
+
# In the following window click '''Install''' button.
−
4. In the following window click Install button.
+
# Setup will continue installing the driver and eventually the confirmation window will appear. Click '''Finish''' to complete the setup.
−
 
 
−
5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the
 
−
setup.
 
  
 
=='''CONFIGURATION (WINDOWS)'''==
 
=='''CONFIGURATION (WINDOWS)'''==
Line 46: Line 43:
 
At first FTC921 device will have default factory settings set. These settings should be changed according to the user's needs. Main
 
At first FTC921 device will have default factory settings set. These settings should be changed according to the user's needs. Main
 
configuration can be performed via [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Teltonika Configurator tool (TCT)].
 
configuration can be performed via [https://wiki.teltonika-gps.com/view/Telematics_Configuration_Tool_(TCT) Teltonika Configurator tool (TCT)].
 +
 +
=='''PINOUT'''==
 +
 +
{| class="wikitable"
 +
|+
 +
! style="width:5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"| PIN NUMBER
 +
! style="width:5%; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"| PIN NAME
 +
! style="width:20 px; border: 1px solid white; border-bottom: 2px solid #0054A6; background: white; color: #0054A6; text-align: left;"|
 +
DESCRIPTION
 +
| rowspan="13" style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |[[Image:FTC921_PINOUT.png|400px|center]]
 +
|-
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8;lenght: 50 px; text-align: left; vertical-align: center; background: white;" | 1
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <span style=color:#FF0000>'''VCC'''</span>
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | (Red) Power supply (+10-90 V DC) (+).
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 2
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <span style=color:#000000>'''GND''' </span>
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | (Black) Ground (-).
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 3
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <span style=color:#FFEF00>'''DIN1'''</span>
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | (Yellow) Digital input, channel 1. DEDICATED FOR IGNITION INPUT. Input range: 7.5-90 V DC.
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 4
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <span style=color:#3B3B3B>'''AIN1'''</span>
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | (Grey) Analog input, channel 1. Input range: 0-90 V DC.
 +
|-
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | 5
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | <span style=color:#E0E0E0>'''DOUT1'''</span>
 +
| style="border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" | (White) Digital output. Open collector output. Max. 0,5 A DC.
 +
|-
 +
|}
  
 
=='''MOUNTING RECOMMENDATIONS'''==
 
=='''MOUNTING RECOMMENDATIONS'''==
−
'''DEVICE FASTENING'''
+
'''CONNECTING WIRES'''
  
−
• Locate the battery in your vehicle. If present remove the battery cover to access the battery.
+
* Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.<br />
−
 
+
* There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.<br />
−
• There is a double sided tape on the back of the device, use it to attach the device on the battery, so that the GNSS antenna
+
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be <br />applied and the wires should not be loose.<br />
−
and LEDs indicators are facing up.
+
* Wires cannot be connected to the board computers or control units.<br />
  
 
'''CONNECTING POWER SOURCE'''
 
'''CONNECTING POWER SOURCE'''
  
−
• Device power wire is designed to be directly connected to the positive terminal fastener of the vehicle battery.
+
* Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.<br />
 +
* When module is connected, measure voltage again to make sure it did not decrease.<br />
 +
* It is recommended to connect to the main power cable in the fuse box.<br />
 +
* 3 A, 125 V external fuse shall be used.<br />
  
 
'''CONNECTING GROUND WIRE'''
 
'''CONNECTING GROUND WIRE'''
  
−
• Connect ground wire to the vehicle frame or metal parts that are fixed to the frame.
+
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.<br />
−
 
+
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.<br />
−
• If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
+
* For better contact scrub paint from the spot where loop is going to be connected.<br />
−
 
 
−
• Device ground wire is designed to be directly connected to the negative terminal fastener of the vehicle battery.
 
  
 
[[Category:FTC921]]
 
[[Category:FTC921]]

Latest revision as of 10:02, 31 May 2024

Main Page > Basic Trackers > FTC921 > FTC921 First Start

Small and smart tracker

FTC921-QJABO-datasheet-2023-09-25.1.png




KNOW YOUR DEVICE

FTC921 KNOW YOUR DEVICE.png

HOW TO INSERT NANO-SIM CARD AND CONNECT THE BATTERY

  1. Gently remove FTC921 cover using plastic pry tool from one side.
  2. Gently remove FTC921 cover using plastic pry tool from another side.
  3. Insert Nano-SIM card as shown. Make sure that Nano-SIM card cut-off corner is pointing forward to slot.
  4. Connect the battery as shown on device. Position the battery in place where it does not obstruct other components.
  5. Attach device cover back. Device is ready to be connected.

FTC921 How to insert SIM card 1.png FTC921 How to insert SIM card 2.png


Alert.png
 Nano-SIM card insertion/removal must be performed when device is powered off – external voltage and internal battery disconnected. Otherwise Nano-SIM card might be damaged or device will not detect it.

PC CONNECTION (WINDOWS)

  1. Power- up FTC921 with DC voltage (10-90V) power supply using power wires. LEDs should start blinking, see “LED behaviour description”.
  2. Connect device to computer using USB Type-C cable and install USB driver, see "HOW TO INSTALL USB DRIVERS (WINDOWS)".

HOW TO INSTALL USB DRIVERS (WINDOWS)

  1. Please download COM port drivers from here.
  2. Extract and run TeltonikaCOMDriver.exe.
  3. Click Next in driver installation window.
  4. In the following window click Install button.
  5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

CONFIGURATION (WINDOWS)

At first FTC921 device will have default factory settings set. These settings should be changed according to the user's needs. Main configuration can be performed via Teltonika Configurator tool (TCT).

PINOUT

PIN NUMBER PIN NAME

DESCRIPTION

FTC921 PINOUT.png
1 VCC (Red) Power supply (+10-90 V DC) (+).
2 GND (Black) Ground (-).
3 DIN1 (Yellow) Digital input, channel 1. DEDICATED FOR IGNITION INPUT. Input range: 7.5-90 V DC.
4 AIN1 (Grey) Analog input, channel 1. Input range: 0-90 V DC.
5 DOUT1 (White) Digital output. Open collector output. Max. 0,5 A DC.

MOUNTING RECOMMENDATIONS

CONNECTING WIRES

  • Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
  • There should be no exposed wires. If factory isolation was removed while connecting wires, the isolation material should be applied.
  • If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be
    applied and the wires should not be loose.
  • Wires cannot be connected to the board computers or control units.

CONNECTING POWER SOURCE

  • Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on car, this may happen in 5 to 30 minutes period.
  • When module is connected, measure voltage again to make sure it did not decrease.
  • It is recommended to connect to the main power cable in the fuse box.
  • 3 A, 125 V external fuse shall be used.

CONNECTING GROUND WIRE

  • Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
  • If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
  • For better contact scrub paint from the spot where loop is going to be connected.
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=FTC921_First_Start&oldid=98710"