Test-AC: Difference between revisions

Revision as of 16:58, 3 February 2026

Power Saving settings

Puts the device into a power-saving mode, preserving the power consumption from the external source or the internal battery.

Online Sleep

In Online Sleep mode, the device manages the connection only when records need to be sent. The connection is opened at periodic intervals to send records and closed immediately after, without any timeout.
Changing the Permanent Link setting during Online Sleep will wake up the device to apply the new configuration.
With Permanent Link enabled, the device maintains a constant connection, sending records immediately as they are generated, rather than waiting for the next scheduled send. After sending connection remains open.

Module	Entry Conditions	Exit conditions	Disabled functions
Main	Configured Ignition source is off. Movement is not detected by the configured Movement source. Device time must be synchronized, as this condition depends on the Record Settings -> Saving / sending mode parameter After Position Fix - device time is synchronized with GNSS satellites and GPS fix is obtained. After Time Sync - device time is synchronized over NTP, NITZ, or GNSS satellites. Always - device will enter sleep mode without time synchronization and GPS fix. Sleep timeout is reached. No SMS messages are being received. No open Data sockets (ignored with enabled permanent link) No active FOTA WEB connection progress.	Ignition is ON. Movement is detected. Periodic wake-up (if enabled).	GNSS Odometer Data acquisition SNTP time synchronization Overspeeding Trip Unplug Detection Jamming Detection Eco Driving

Deep Sleep

During Deep Sleep mode, the device generates and stores periodic records.

Module	Entry Conditions	Exit conditions	Disabled functions
Main	Configured Ignition source is off. Movement is not detected by the configured Movement source. Device time must be synchronized, as this condition depends on the Record Settings -> Saving / sending mode parameter. After Position Fix - device time is synchronized with GNSS satellites and GPS fix is obtained. After Time Sync - device time is synchronized over NTP, NITZ, or GNSS satellites. Always - device will enter sleep mode without time synchronization and GPS fix. Sleep timeout is reached. No SMS messages are being received. No open Data sockets (ignored with enabled permanent link) No active FOTA WEB connection progress.	Ignition is ON. Movement is detected. Periodic wake-up (if enabled).	Modem Record sending GNSS IMU (Inertial Measurement Unit) FOTA WEB LEDs (Navigation and Status) Odometer Data acquisition SNTP time synchronization Overspeeding Trip Unplug Detection Jamming Detection Eco Driving

Power Off Sleep

When device goes into sleep mode, some modules are turned off to consume less power. Listed below are the modules and scenarios that are turned off in common with all modes and those that are disabled specifically for the Power off sleep mode:

Module

Entry Conditions

Exit conditions

Disabled functions

Main

Configured Ignition source is off.
Movement is not detected by the configured Movement source.
Device time must be synchronized, as this condition depends on the Record Settings -> Saving / sending mode parameter
After Position Fix - device time is synchronized with GNSS satellites and GPS fix is obtained.
After Time Sync - device time is synchronized over NTP, NITZ, or GNSS satellites.
Always - device will enter sleep mode without time synchronization and GPS fix.
Sleep timeout is reached.
No SMS messages are being received.
No open Data sockets (ignored with enabled permanent link)
No active FOTA WEB connection progress.

Ignition is ON.
Movement is detected.

Modem
Record sending
GNSS
IMU (Inertial Measurement Unit)
FOTA WEB
Charger service
LEDs (Navigation and Status)
Odometer
Data acquisition
SNTP time synchronization
Overspeeding
Trip
Unplug Detection
Jamming Detection
Eco Driving

@@ Line 1: / Line 1: @@
-==Table - New Content==
+==Power Saving settings==
 {{#switch: {{{model}}}
 | #default =
@@ Line 33: / Line 33: @@
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">'''''Main'''''</td>
 <td style="vertical-align: middle; text-align: left; min-width: 550px; border-bottom: 3px solid #111;">
-*Ignition (configured ignition source) is off.<br>
+*Configured '''Ignition source''' is off.<br>
-*Movement is not detected by the configured movement source.<br>
+*Movement is not detected by the configured '''Movement source'''.<br>
-*Device time must be synchronized. This condition depends on the “Record Settings -> Saving / sending mode parameter.<br>
+*Device time must be synchronized, as this condition depends on the ''Record Settings -> Saving / sending mode'' parameter<br>
 *After Position Fix - device time is synchronized with GNSS satellites and GPS fix is obtained.<br>
 *After Time Sync - device time is synchronized over NTP, NITZ, or GNSS satellites.<br>
 *Always - device will enter sleep mode without time synchronization and GPS fix.<br>
 *Sleep timeout is reached.<br>
-*There are no SMS messages being received.<br>
+*No SMS messages are being received.<br>
-*Data sockets are closed (ignored when permanent link is enabled)<br>
+*No open Data sockets (ignored with enabled permanent link)<br>
-*FOTA WEB connection is not in progress.<br>
+*No active FOTA WEB connection progress.<br>
 </td>
 <td style="vertical-align: middle; horizontal-align: center; min-width: 150px; border-bottom: 3px solid #111;">
@@ Line 63: / Line 63: @@
 <tr>
+{{#if: {{FTX Pin Support List|model={{{model}}}|pin=Manual CAN}} |
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">'''''CAN'''''</td>
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">
@@ Line 74: / Line 75: @@
 *CAN
 </td>
+}}
 </tr>
 <tr>
+{{#if: {{FTX Pin Support List|model={{{model}}}|pin=Manual BT}} |
 <td style="vertical-align: middle; text-align: left;">'''''BLE'''''</td>
 <td style="vertical-align: middle; text-align: left;">
@@ Line 87: / Line 89: @@
 *DIN pins remain active in sleep mode and can be used as wake-up sources for the device.</td>
 <td style="vertical-align: middle; text-align: left;"> </td>
+}}
 </tr>
@@ Line 108: / Line 111: @@
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">'''''Main'''''</td>
 <td style="vertical-align: middle; text-align: left; min-width: 550px; border-bottom: 3px solid #111;">
-*Ignition (configured ignition source) is off.
+*Configured '''Ignition source''' is off.
-*Movement is not detected by the configured movement source.
+*Movement is not detected by the configured '''Movement source'''.
-*Device time must be synchronized. This condition depends on the “Record Settings -> Saving / sending mode parameter.
+*Device time must be synchronized, as this condition depends on the ''Record Settings -> Saving / sending mode'' parameter.
 *After Position Fix - device time is synchronized with GNSS satellites and GPS fix is obtained.
 *After Time Sync - device time is synchronized over NTP, NITZ, or GNSS satellites.
 *Always - device will enter sleep mode without time synchronization and GPS fix.
 *Sleep timeout is reached.
-*There are no SMS messages being received.
+*No SMS messages are being received.
-*Data sockets are closed (checks if record sending socket link is open)
+*No open Data sockets (ignored with enabled permanent link)<br>
-*FOTA WEB connection is not in progress.
+*No active FOTA WEB connection progress.
 </td>
 <td style="vertical-align: middle; horizontal-align: center; min-width: 150px; border-bottom: 3px solid #111;">
@@ Line 143: / Line 146: @@
 <tr>
+{{#if: {{FTX Pin Support List|model={{{model}}}|pin=Manual CAN}} |
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">'''''CAN'''''</td>
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">
@@ Line 156: / Line 160: @@
 *CAN
 </td>
+}}
 </tr>
 <tr>
+{{#if: {{FTX Pin Support List|model={{{model}}}|pin=Manual BT}} |
 <td style="vertical-align: middle; text-align: left;">'''''BLE'''''</td>
 <td style="vertical-align: middle; text-align: left;">
@@ Line 173: / Line 179: @@
 *BLE scanning
 </td>
+}}
 </tr>
 </table>
@@ Line 192: / Line 200: @@
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">'''''Main'''''</td>
 <td style="vertical-align: middle; text-align: left; min-width: 550px; border-bottom: 3px solid #111;">
-*Ignition (configured ignition source) is off.
+*Configured '''Ignition source''' is off.
-*Movement is not detected by the configured movement source.
+*Movement is not detected by the configured '''Movement source'''.
-*Device time must be synchronized. This condition depends on the “Record Settings -> Saving / sending mode parameter.
+*Device time must be synchronized, as this condition depends on the ''Record Settings -> Saving / sending mode'' parameter
 *After Position Fix - device time is synchronized with GNSS satellites and GPS fix is obtained.
 *After Time Sync - device time is synchronized over NTP, NITZ, or GNSS satellites.
 *Always - device will enter sleep mode without time synchronization and GPS fix.
 *Sleep timeout is reached.
-*There are no SMS messages being received.
+*No SMS messages are being received.
-*Data sockets are closed (ignored when permanent link is enabled)
+*No open Data sockets (ignored with enabled permanent link)<br>
-*FOTA WEB connection is not in progress.
+*No active FOTA WEB connection progress.
 </td>
 <td style="vertical-align: middle; horizontal-align: center; min-width: 150px; border-bottom: 3px solid #111;">
@@ Line 235: / Line 243: @@
 <tr>
+{{#if: {{FTX Pin Support List|model={{{model}}}|pin=Manual CAN}} |
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">'''''CAN'''''</td>
 <td style="vertical-align: middle; text-align: left; border-bottom: 3px solid #111;">
@@ Line 245: / Line 254: @@
 *CAN (''does not receive requests, does not read CAN bus messages'')
 </td>
+}}
 </tr>
 <tr>
+{{#if: {{FTX Pin Support List|model={{{model}}}|pin=BT}} |
 <td style="vertical-align: middle; text-align: left;">'''''BLE'''''</td>
 <td style="vertical-align: middle; text-align: left;">
@@ Line 260: / Line 271: @@
 *Anything connected or enabled by BLE module(1 wire, DIN's, DOUT's, BLE as a peripheral)
 </td>
+}}
 </tr>
 </table>