Difference between revisions of "EYE SENSOR Test"

Revision as of 20:12, 22 March 2024

Main Page > Advanced Trackers > EYE SENSOR Test

Introduction

Wireless solutions open up new horizons for your business and help to keep an eye on your assets. Discover our brand-new and certified Bluetooth® Low Energy ID sensor model from Teltonika with robust waterproof casing and a long-lifetime battery. The model is designed for a low-cost fast and easy configuration and integration to save precious time, resources, and ensure accountability.

About BTSMP1

Perfect for traceability use cases, delivery tracking, monitoring of various movable objects in logistics (trailers, containers), agriculture (tractor attachments), and constructions (tools and inventory). Sensors data makes it especially suitable for cold chain refrigerator use cases. The built-in accelerometer can detect item movement, pitch and roll of the device. Magnet detection can be used for wireless open/close detection and notifications such as trailer door events, etc. EYE sensor supports iBeacon and Eddystone protocols. The device is fully compatible with the Teltonika firmware platform which provides extended functionality. Configure, scan, and update anytime anywhere with a dedicated Teltonika mobile app

Product Specification

Features


Functionalities
Beacon ID, LED, Temperature, Humidity, Accelerometer, Magnet detection


Dimensions and weight
Dimensions	56,6 mm x 38 mm x 13 mm
Weight	18g


Battery and power
Model	CR2450
Type	Type Lithium, Manganese Dioxide
Total Capacity	600 mAh
Replaceable	No
Battery life (Tx=2 dBm; interval: 3 s)	2.5+ years
Battery life (Tx=2 dBm; interval: 5 s), default	4+ years
Battery life (Tx=2 dBm; interval: 10 s)	5+ years


Connectivity
Bluetooth®	Bluetooth® 4.2 compliant, Bluetooth® 5.2 certified
Range	80 m
Available transmission power levels	Up to 8 dBm
Sensitivity	-88 dBm


Casing
Protection	IP67
Mounting	Two holes to screw/leash/strip, tape
Customization	Custom logo upon request (Special conditions)


Environmental Requirements
Humidity (non-condensing)	From 0% to 100%
Operational temperature	-20°C / +60°C (-4°F / +140°F)


Protocols compatibility
iBeacon	Yes *iOS doesn't show devices with iBeacon protocol
Eddystone	Yes
EYE Sensor	Yes

Dimensions

Value-adding Features

Hibernate mode

Hibernated mode means that the EYE device is OFF when shipping from the factory, preserving battery life. PLEASE NOTE that EYE devices are available in two modes: factory-activated (ON) or Hibernated (OFF). You may order the device version which better suits your needs. Order codes are described on eye page

Value of hibernate mode

Hibernated versions of EYE devices simplify stock management for our partners while maximizing battery life.
1. Accelerated delivery times:

By stocking up on hibernated EYE devices, you ensure readiness to deploy EYE devices with full battery capacity at any moment. This proactive approach provides fastest possible service, increases your reputation for efficiency and positions you as an industry frontrunner, enhancing your competitive edge.

2. Mitigated project risks:

In scenarios where projects encounter unforeseen challenges, our hibernated EYE devices offer a buffer. Hibernate feature allows to safeguard your investments and potential revenue streams. This means that even if projects encounter delays or complications, you can still deploy EYE devices with full battery capacity, ensuring optimal performance when the time is right.

How to activate hibernated eye device?

Attach any magnet to sleeping device and wait for LED to blink.
NOTE: ANY MAGNET CAN BE USED

Now device is discoverable, scannable, connectable via BLE.

How to send the device to hibernate mode?

If you want to put the EYE device back to hibernate mode after accidental activation or simply pause its use, you may do that following steps below:
Step 1. While connected and in overview tap "Send device to sleep":
Step 2. Confirm your selection:
Step 3. Wait for EYE App to disconnect:

Can All devices hibernate?

1. All EYE Sensors with firmware version starting from 1.2.9.R.8 can hibernate.

2. Only new EYE Beacons bought with order codes that have hardware modification can hibernate standard codes are available in eye page, for special order codes consult your sales manager.

Mounting recomendations

EYE App Configuration

Devices work constantly and are ready to perform out of the box. Default basic Sensor settings are set to:
• Transmitting at 2 dBm power.
• Data advertising at 1 second intervals.
• Eddystone and Sensors protocol

If you would like to change these settings you will need to:
1) Download and install EYE APP - Teltonika application to change sensor settings.

Eye App Overview

With the application you will be able to scan for visible Teltonika EYE devices, check their statuses or connect for configuration or firmware update.

Devices in view

In this window you will see all visible devices. You have options to see devices in Short list or in default list. When looking at devices in default list you will be able to open Detailed view of devices and check transmitted data statuses. Additionaly if you are looking for specific devices you will be able to use Search function to filter search options. When in this window select a device of your choice to connect and after passing pin code (default pin code is 123456) you will go to device overview window.

Overview window

In overview window you can see device details, check firmware version and update if available, go to device configuration settings and download the configuration. If you select to Configure device new window will open with Basic and Advanced settings. Other actions include changing the device PIN code and putting the device to sleep. A device in sleep mode will no longer be findable or connectable via the app. To wake it up, you need to attach a magnet and look for a green LED flashing.

Configure window

In this window you can check and change device configuration settings. In main tab Basic Settings you can change main settings. Change Device name, Power signal strength, Advertising interval and Packet transmission type*. For more settings go to Advanced settings tab to enable various events.

Advanced configuration window

Advanced configuration: Beacon Settings

In Advanced settings tab you can can configure EYE beacon sensor parameters: Beacon information (iBeacon ID*, Eddystone ID). UUID/MINOR/MAJOR parameter can be changed for iBeacon ID*. Namespace ID/Instance ID can be changed for Eddystone ID. If you scroll down you will be able to adjust Sensor reading interval and event settings of the EYE Sensor Note: iOS doesn't show devices with iBeacon protocol

Advanced configuration: Sensor reading and events

!NOTE: These settings are no longer available after EYE APP 1.2.0-60 update.


Magnetic field event - adjust if the device generates events based on detection or exit (loss) of the magnet.	Humidity event - adjust if the device generates events based on entrance or exit to selected humidity range	Temperature event - adjust if the device generates events based on entrance or exit to selected temperature range	Movement event - adjust movement/stop detection and timeouts it takes to register movement / stopping

Maximum event duration - how long will one event be advertised	Event advertising settings - advertising period after event detection	Sensor reading interval - how often values are updated by the device

FM Tracker Configuration

Teltonika configurator (Base firmware / advanced mode)

If you have firmware / configurator which does not support EYE sensor tab in Bluetooth® 4.0 section, then you can still use Avanced BLE configuration to connect with EYE Sensors.

To configure FM with BTSMP1 EYE Sensor:

Requirements:

Firmware/configurator version with multiple custom IO fields per sensor, we recommend:

FMBXXX: 03.27.07.Rev.00/1.7.22_B.3.27_R.21 or newer

FMX640: 01.02.03/1.7.24_B.FM64_R.34 or newer (FMB640 does not support for BLE functionality)

Step 1: Check EYE App Settings:

Make sure that name of the sensor is default length (10 symbols) in EYE App Basic Configuration window
Note what Packet settings you have set in EYE App Basic Configuration window

Step 2: Configure FM device using Teltonika configurator:

In System settings Enable Codec8 Extended;
In GPRS settings Configure GPRS Settings and Server Settings
In Bluetooth® settings Enable Bluetooth®, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth® will be disabled;
In Bluetooth® 4.0 settings:
1. set Non Stop Scan to "Disable", configure "Update Frequency" and "Scan duration" as 30 seconds. These settings will bring the best results for BLE scanning with our device;
2. In Bluetooth® 4.0 settings Advanced Mode Settings Load EYE Sensor preset according to packet settings in EYE app(if you do not have preset you can download them from below table)
3. Configure MAC address of the sensor
To receive data to server enable corresponding IO elements in FMB120 I/O settings

Advanced mode configuration:

EYE Sensor Packet Setting:
Preset you should use:	EYE Sensors	EYE iBeacon	EYE Eddystone
FMBXXX Preset download link:
FMBXXX Configuration example download link:
FMX640 Preset download link:
Instructions how you can manually add a preset: link

Preset Configuration:

If EYE Sensor Packet Settings is EYE Sensors or Eddystone and EYE Sensors:

If EYE Sensor Packet Settings is EYE Sensors or iBeacon and EYE Sensors:

IO element value descriptions:


NAME	DESCRIPTION
Custom1	Flags (not supported with current FMX640 preset)
Temperature	Ambient temperature in Celsius
Humidity	Ambient humidity in percent
Custom2	Movement and movement events count
Custom3	Angle
Custom4	Battery voltage (2000 + (VALUE * 10)) in mV

Property ID in AVL packet	Property name	Bytes	Type	Min	Max	Multiplier	Units	Description
25	BLE Temperature #1	2	Signed	-4000	12500	0.01*	°C	Degrees ( °C ), -40 - +125; Error codes: 4000 - abnormal sensor state 3000 - sensor not found 2000 - failed sensor data parsing
26	BLE Temperature #2	2	Signed	-4000	12500	0.01*	°C	Degrees ( °C ), -40 - +125; Error codes: 4000 - abnormal sensor state 3000 - sensor not found 2000 - failed sensor data parsing
27	BLE Temperature #3	2	Signed	-4000	12500	0.01*	°C	Degrees ( °C ), -40 - +125; Error codes: 4000 - abnormal sensor state 3000 - sensor not found 2000 - failed sensor data parsing
28	BLE Temperature #4	2	Signed	-4000	12500	0.01*	°C	Degrees ( °C ), -40 - +125; Error codes: 4000 - abnormal sensor state 3000 - sensor not found 2000 - failed sensor data parsing
86	BLE Humidity #1	2	Unsigned	0	1000	0.1*	%RH	Humidity
104	BLE Humidity #2	2	Unsigned	0	1000	0.1*	%RH	Humidity
106	BLE Humidity #3	2	Unsigned	0	1000	0.1*	%RH	Humidity
108	BLE Humidity #4	2	Unsigned	0	1000	0.1*	%RH	Humidity
331	BLE 1 Custom #1	Variable	HEX	0	-	-	-	Custom IO element for BLE sensor
463	BLE 1 Custom #2	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
464	BLE 1 Custom #3	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
465	BLE 1 Custom #4	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
466	BLE 1 Custom #5	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
332	BLE 2 Custom #1	Variable	HEX	0	-	-	-	Custom IO element for BLE sensor
467	BLE 2 Custom #2	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
468	BLE 2 Custom #3	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
469	BLE 2 Custom #4	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
470	BLE 2 Custom #5	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
333	BLE 3 Custom #1	Variable	HEX	0	-	-	-	Custom IO element for BLE sensor
471	BLE 3 Custom #2	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
472	BLE 3 Custom #3	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
473	BLE 3 Custom #4	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
474	BLE 3 Custom #5	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
334	BLE 4 Custom #1	Variable	HEX	0	-	-	-	Custom IO element for BLE sensor
475	BLE 4 Custom #2	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
476	BLE 4 Custom #3	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
477	BLE 4 Custom #4	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor
478	BLE 4 Custom #5	8	UNSIGNED LONG INT	0	4294967295	-	-	Custom IO element for BLE sensor

Teltonika configurator new functionalities (Evaluation firmware / EYE Sensor filtering by name)

Starting with firmware 03.28.04.Rev.207 there is additional tabs available in Bluetooth® 4.0 section that allow for easier configuration to connect FM and EYE sensor or beacon.

It's now possible to connect up to 100 sensors at once just by entering one name in the configurator name list. It's required to enter at least 3 characters(case sensitive) in the name for FM to scan the sensors. Super easy to set up!

For example, the you may order Sensors with special configuration from factory where the EYE Sensor names would be TRAILER_1,TRAILER_2,...,TRAILER_99 and so on.

If you would enter TRAILERS in the EYE Fimrware FM configurator then sensors who meet this name condition, for example TRAILER_1, TRAILER_21 , TRAILER_17, would be scanned, while other sensors named Tools, MP1_123546, etc. will not be scanned. With this option, you can upload one configuration to FOTA web and it doesn’t matter which sensor from the list end user will mount, it will be scanned and sent to the server as long as it meets the name criteria.

Bluetooth® 4.0
Functionalities were reorganized and transferred to Bluetooth® 4.0 configuration tab with additional horizontal tabs selection for specific settings:

Global - Parameters responsible for device scanning ability like power and duratations.
EYE - Parameters to configure data reading from EYE sensors.

Common settings

Non Stop Scan - Enable Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
Sensors and Beacons Update frequency - changes sensors temperature/humidity/battery voltage data update frequency. Minimum value: 30s, maximum value: 65535s. Recommended value 30.
BLE Scan Duration - Sensors data reading time. Recommended value 30.
Scan retries until error - Scan retries count, till start to show the value as Error '3000' - sensor disconnected. Recommended value 30.
BT Power Level - Telematics device Bluetooth® power level setting.
BLE Broadcasting service ID - Telematics device can broadcast configured ID.
BLE connection control - Connection mode settings. If broadcasting ID is configured, parameter should be set to Prohibit.

Sensors
Sensor Configuration can be set to Custom Sensors, Eye Sensors or both. With the Custom Sensors setting enabled, any BLE sensor can be configured.
When EYE Sensors is selected, Eye Sensor connectionless functionalities or EYE list search window will appear, depending on the selected EYE Sensor filter.

Name
When EYE Sensors Filter is set to Name, the Eye List search window will appear on the configurator. With this setting, separate EYE Sensor records (AVL ID: 11317) will be generated according to the configured parameters, which are described below:

Data Clear period- defines how long the FM tracker waits when the Eye sensor is not detected before removing it from the Eye Sensor list and not sending the sensor values. If Data Clear Period is set to 0, then the EYE Sensor will not be removed from the EYE Sensor list and it will always be included in the periodic records.

RSSI- Parameter defines the dBm threshold value of when the EYE sensor will be added to the sensor list. If the FM tracker detects the RSSI lower than the configured value, it will not be added to the EYE Sensor list.

Record period - Defines how often the EYE Sensor record (AVL ID: 11317) will be generated when the FM tracker is operating On Stop or On Move modes, according to the configured movement source..

EYE Sensor Settings - Define what sensor readings data is included in to the EYE Sensor Records. Sensor readings which are not needed can be disabled, to reduce data consumption.
EYE Name list - Defines what EYE sensors will be added to EYE Sensor list. For EYE Sensors to be added to the list, only the beginning part of the EYE Sensor local name has to match. For example, if in the EYE name list “EYE_SENSOR” is added and the FM tracker detects EYE_SENSOR1, EYE_SENSOR2, EYE_SENSORXYZ, all these EYE Sensors will be added to EYE Sensor list. If the EYE name list is left empty, all the detected EYE Sensors will be included in the EYE Sensor list. NOTE: If EYE Sensor has a name that matches configured one in EYE Name List and if it has a MAC address, that matches configured one in EYE Sensors filtered by MAC address, then such sensor will not be added to EYE Sensor list, but it’s data will be added according EYE Sensor filtered by MAC IO elements.

Once Eye Sensor filtering by name list is selected, EYE Sensor records containing the AVL ID:11317 will start being generated. Below is an example of how EYE Sensor data is packed into AVL ID 11317
AVL ID 11317 structure


Eye Sensor #1
EYE Sensor #1 Data length	1 byte
1st Parameter ID	1 byte
1st Parameter Data Length	1 byte
1st Parameter Data	variable
2nd Parameter ID	1 byte
2nd Parameter Data Length	1 byte
2nd Parameter Data	variable
<...>
Nth Parameter ID	1 byte
Nth Parameter Data Length	1 byte
Nth Parameter Data	variable
Eye Sensor #2
Eye Sensor #2 Data length	1 byte
1st Parameter ID	1 byte
1st Parameter Data Length	1 byte
1st Parameter Data	variable
2nd Parameter ID	1 byte
2nd Parameter Data Length	1 byte
2nd Parameter Data	variable
<...>
Nth Parameter ID	1 byte
Nth Parameter Data Length	1 byte
Nth Parameter Data	variable
Eye Sensor #N
...	...

Parameter IDs are used to identify what type of EYE Sensor information is included in the packet. Below is the table describing the possible EYE Sensor parameter IDs, along with their data type and data length.

**Table 1. EYE Sensor Parameter IDs**
Parameter ID	Name	Data type	Description
5	Eye Sensor Device Name	Array	Device’s name from Device Name List tab
6	EYE Sensor Temperature	2 byte signed integer	Temperature value measured by EYE Sensor from List Values from -32768 to +32768 with 0.01 C delta
7	EYE Sensor Humidity	1 byte unsigned integer	Humidity measured by EYE Sensor from List Values from 0 to 100%
8	EYE Sensor Magnet presence	1 byte unsigned integer	Magnet measured by EYE Sensor from List Values from 0 to1
9	EYE Sensor Movement presence	1 byte unsigned integer	Movement measured by Eye Sensor from List Values
10	EYE Sensor Movement count	2 byte unsigned integer	Movement counts measured by EYE Sensor from List Values
11	EYE Sensor Pitch	1 byte signed integer	Pitch angle measured by Eye Sensor from list Values
12	EYE Sensor Angle Roll	2 byte signed integer	Roll Angle measured by EYE Sensor from List Values
13	EYE Sensor Low battery indicator	1 byte unsigned integer	Low battery state measured by EYE Sensor from List Values from 0 to1
14	EYE Sensor Battery voltage	2 byte unsigned integer	Low battery state measured by EYE Sensor from List Values from 0 to1
15	EYE Sensor MAC adress	6 byte unsigned integer	Device's MAC adress
16	EYE Sensor Magnet trigger count*	2 byte unsigned integer	Magnet trigger counts measured by EYE Sensor from List Values *Only available with evaluation firmware BTSX.1.2.8.magcounter.R.0 of EYE Devices

MAC
IF EYE Sensors are selected to be filtered by MAC address, separate EYE sensor records will not be generated; EYE sensor values will be included into regular records with their corresponding IO elements. Up to 4 EYE Sensors can be configured with different MAC Addresses. In the case of filtering by MAC Address, more advanced configuration is possible, as EYE Sensors’ IOs’ Low, High level, Event Only and Operand parameters can also be configured separately for each IO.

Working Mode - parameter has 2 options – Disabled and EYE Sensor. When it is disabled, EYE Sensor IO values will not be included into the records. When EYE Sensor is selected, EYE Sensor IO values will be included into records.
MAC Settings - parameter specifies the MAC address of the EYE Sensor for the FM tracker to read, parse its data and put to corresponding IO elements. If the sensor is not found for set amount of scan retries, error values will be stored into IO elements.
I/O elements - allows for advanced EYE sensor I/O elements configuration.

EYE Sensor AVL IDs

Table below describes I/O elements which were added for EYE sensor with the new functionalities release.

Property ID in AVL packet	Property name	Bytes	Type	Min	Max	Multiplier	Units	Description
11317	EYE Sensor List	variable length	HEX	0 bytes	1024 bytes	-	-	EYE Sensor List
10800	EYE Temperature 1	2	Signed	-32768	32768	0,01	°C	Temperature measured by EYE sensor 1
10801	EYE Temperature 2	2	Signed	-32768	32768	0,01	°C	Temperature measured by EYE sensor 2
10802	EYE Temperature 3	2	Signed	-32768	32768	0,01	°C	Temperature measured by EYE sensor 3
10803	EYE Temperature 4	2	Signed	-32768	32768	0,01	°C	Temperature measured by EYE sensor 4
10804	EYE Humidity 1	1	Unsigned	0	100	-	%	Humidity measured by EYE sensor 1
10805	EYE Humidity 2	1	Unsigned	0	100	-	%	Humidity measured by EYE sensor 2
10806	EYE Humidity 3	1	Unsigned	0	100	-	%	Humidity measured by EYE sensor 3
10807	EYE Humidity 4	1	Unsigned	0	100	-	%	Humidity measured by EYE sensor 4
10808	EYE Magnet 1	1	Unsigned	0	1	-	-	Magnet measured by EYE sensor 1
10809	EYE Magnet 2	1	Unsigned	0	1	-	-	Magnet measured by EYE sensor 2
10810	EYE Magnet 3	1	Unsigned	0	1	-	-	Magnet measured by EYE sensor 3
10811	EYE Magnet 4	1	Unsigned	0	1	-	-	Magnet measured by EYE sensor 4
10812	EYE Movement 1	1	Unsigned	0	1	-	-	Movement state and count measured by EYE sensor 1
10813	EYE Movement 2	1	Unsigned	0	1	-	-	Movement state and count measured by EYE sensor 2
10814	EYE Movement 3	1	Unsigned	0	1	-	-	Movement state and count measured by EYE sensor 3
10815	EYE Movement 4	1	Unsigned	0	1	-	-	Movement state and count measured by EYE sensor 4
10816	EYE Pitch 1	1	signed	-90	90	-	-	Pitch and Roll angles measured by EYE sensor 1
10817	EYE Pitch 2	1	signed	-90	90	-	-	Pitch and Roll angles measured by EYE sensor 2
10818	EYE Pitch 3	1	signed	-90	90	-	-	Pitch and Roll angles measured by EYE sensor 3
10819	EYE Pitch 4	1	signed	-90	90	-	-	Pitch and Roll angles measured by EYE sensor 4
10820	EYE Low Battery 1	1	Unsigned	0	1	-	-	Low Battery indication EYE sensor 1
10821	EYE Low Battery 2	1	Unsigned	0	1	-	-	Low Battery indication EYE sensor 2
10822	EYE Low Battery 3	1	Unsigned	0	1	-	-	Low Battery indication EYE sensor 3
10823	EYE Low Battery 4	1	Unsigned	0	1	-	-	Low Battery indication EYE sensor 4
10824	EYE Battery Voltage 1	2	Unsigned	0	65535	-	-	Battery Voltage of EYE sensor 1
10825	EYE Battery Voltage 2	2	Unsigned	0	65535	-	-	Battery Voltage of EYE sensor 2
10826	EYE Battery Voltage 3	2	Unsigned	0	65535	-	-	Battery Voltage of EYE sensor 3
10827	EYE Battery Voltage 4	2	Unsigned	0	65535	-	-	Battery Voltage of EYE sensor 4
10832	EYE Roll 1	2	signed	-180	180	-	-	Roll value of EYE Sensor 1
10833	EYE Roll 2	2	signed	-180	180	-	-	Roll value of EYE Sensor 2
10834	EYE Roll 3	2	signed	-180	180	-	-	Roll value of EYE Sensor 3
10835	EYE Roll 4	2	signed	-180	180	-	-	Roll value of EYE Sensor 4
10836	EYE Movement Count 1	2	unsigned	0	65535	-	-	Movement count value of EYE Sensor 1
10837	EYE Movement Count 2	2	unsigned	0	65535	-	-	Movement count value of EYE Sensor 2
10838	EYE Movement Count 3	2	unsigned	0	65535	-	-	Movement count value of EYE Sensor 3
10839	EYE Movement Count 4	2	unsigned	0	65535	-	-	Movement count value of EYE Sensor 4

Eye sensor parameters have error code values, which will written to the I/O value if parameter data is not received. From the error code value, it is possible to distinguish whether the issue is on the FM tracker side or the EYE Sensor. Below is a table describing these values.

Eye Sensor Error Values
Parameter	Data length (bytes)	Data type	Error codes		Additional Notes
Parameter	Data length (bytes)	Data type	Data Not Received by FM tracker	EYE Sensor indicates error
Temperature	2	signed	25000	25001
Humidity	1	unsigned	250	251
Magnet	1	unsigned	250	251
Magnet trigger count	2	unsigned	65000	65001	Only available with evaluation firmware BTSX.1.2.8.magcounter.R.0 of EYE Devices
Movement	1	unsigned	250	251
Movement counter	2	unsigned	65000	65001
Pitch	1	signed	120	121
Roll	2	signed	250	251
Low battery status	1	unsigned	250	251
Battery voltage	1	unsigned	250	251

Note: If you are using presets(firmware/configurator without EYE product support), then refer to BLE Sensors I/O elements table instead.

New EYE Features (Proximity and Lost & Found)

Proximity

EYE beacon Proximity events is a functionality which creates three different types of records, depending on the captured Beacons RSSI level. This functionality is only supported with Teltonika EYE beacons. Proximity events consist of near, away and lost events:

When EYE beacon RSSI level is below the first configured threshold, the beacon will be added to Near Beacon Record (AVL ID: 10828)
When EYE BEACON RSSI level is between the second and first configured threshold, beacon is added to Away Beacon record (AVL ID: 10829)
When EYE Beacon RSSI level is lower than the second configured threshold, beacon is added to Lost Beacon record (AVL ID: 10831). In the case of EYE Beacon disappearing from the environment and not being detected by the FM tracker anymore, the beacon will be added to Lost Beacon record and will be removed from Beacon list.

Event modes

Disabled – Record generating is disabled for the selected range
Periodic – Records will be periodically generated for the selected range, according to the configured record period on move or on stop value.
On Change – Records will be generated as soon as the Eye Beacon number changes for the selected range.

Averaging Timeout

This parameter specifies how long it will take current RSSI value to reach new RSSI value. For example, current EYE Beacon RSSI value is -40 dBm. FMB captures same EYE Beacon with RSSI value of -60 dBm. If averaging timeout is configured to be 10 seconds, it will take 10 seconds for RSSI value to reach -60 dBm from -40 dBm. Keep in mind that this is assuming perfect conditions and subsequent EYE Beacon RSSI.

Lost & Found

Purpose of this functionality is to periodically generate records with all EYE Beacon list (AVL ID: 10828) and create eventual On Change records only when EYE Beacon is lost (AVL ID: 10831) or found (AVL ID: 10829).

Lost and Found Beacon records only include EYE Beacon which was lost or found, not the full Beacon list.

If multiple EYE Beacons were found or lost at the same time, multiple will be included into the record.
If Visible Beacon List is enabled, Beacon records containing the list of visible beacons will be generated according to the configured period parameters Record Period on Move and Record Period on Stop

Advanced Beacon protocol is being used to send Lost & Found records.

Note:Same AVL ID’s as for Proximity events are being used, since two features cannot work at the same time.

AVL ID: 10828 Visible Beacon List (periodic)
AVL ID: 10829 Found Beacon List (On Change)
AVL ID: 10831 Lost Eye Beacon List (On Change)

Data Parsing

Parsing for Base Functionality (Advanced Mode)


Unparsed data
Received data in hexadecimal stream: `00000000000000488E010000017CA6B6BFD8010F0E5188209AB482008600A80F0000000` `00006000000020019090400560024000301CF0000001601D00000FF4D01D10000006D00000001014B0001B6010000CF7D`

AVL Data Packet
AVL Data Packet Part		HEX Code Part
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 48
	Codec ID	8E (Codec8 Extended)
	Number of Data 1 (Number of Total Records)	01
AVL Data	Timestamp	00 00 01 7C A6 B6 BF D8 (GMT: Friday, 22 October 2021 06:36:07)
	Priority	01
	Longitude	0F 0E 51 88
	Latitude	20 9A B4 82
	Altitude	00 86
	Angle	00 0A
	Satellites	0E
	Speed	00 00
	Event IO ID	00 00
	N of Total ID	00 06
	N1 of One Byte IO	00 00
	N2 of Two Bytes IO	00 02
	ID	00 19 (25 = BLE Temperature #1)
	Value	09 04 (2308=23.08°C)
	ID	00 56 (86 = BLE Humidity #1)
	Value	00 36 (24 %RHT)
	N4 of Four Bytes IO	00 03
	ID	01 CF (463 - BLE 1 Custom #2 = Movement status and movement events count)
	Value	00 00 00 16 (Currently not moving events count 22)
	ID	01 D0 (464 - BLE 1 Custom #3 = Angle )
	Value	00 00 FF 4D (Pitch = 0°, Roll = -179°)
	ID	01 D1 (465 - BLE 1 Custom #4 = Battery Voltage)
	Value	00 00 00 6D (109 = 2000 + 109 * 10 mV = 3090 mV)
	N8 of Eight Bytes IO	00 00
	NX of X Bytes IO	00 01
	N’th IO ID - AVL ID.	01 4B (331 - BLE 1 Custom #1 = Flags)
	Length of Variable Length IO	00 01
	Value of Variable Length IO	B7 = (MSB)11011 0111(LSB) It's parsed from least significant byte(LSB): Bit 0 – Temperature value presence. 1 Means device is reading and transmitting temperature value. Bit 1 – Humidity value presence. 1 Means device is reading and transmitting humidity value. Bit 2 – Magnetic sensor presence. 1 Means device is reading and transmitting Magnetic sensor value. Bit 3 – Magnetic sensor state 1 magnetic field is detected/0 magnetic field is not detected) Valid value is present only if bit 2 flag is set. Bit 4 – Movement sensor counter. 1 Means device is reading and transmitting movement state and count values. Bit 5 – Movement sensor angle. 1 Means device is reading and transmitting angle roll and pitch values. Bit 6 – Low Battery indication. 0 – Means device battery is from 100 to 15 % (When value changes to 1 Battery level is lower than 15 %. 7 – Battery voltage value presence. 1 Means device is reading and transmitting battery voltage value.
	Number of Data 2 (Number of Total Records)	01
	CRC-16	00 00 CF 7D

Parsing for Proximity Feature


PROXIMITY FEATURE
Received data in hexadecimal stream: 00000000000000BD8E03 0000018D1468C11B00E42CC908F1F475CC000000000300002A4C0001000000000000000000012A4C001401120001E50F067CD9F401EF770D01000E020BFE 0000018D1468C12500E42CC908F1F475CC000000000300002A4D0001000000000000000000012A4D001401120001C80F067CD9F40255BE0D01000E020BF4 0000018D1468C12F00E42CC908F1F475CC000000000300002A4F0001000000000000000000012A4F001401120001B90F067CD9F4004B490D01000E020BFE 03000086BA


AVL Data Packet
AVL Data Packet Part		HEX Code Part	Decoded
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 BD	189 bytes
	Codec ID	8E	Codec8 Extended
	Number of Data 1 (Number of Total Records)	03	3
AVL DATA	Timestamp	00 00 01 8D 14 68 C1 1B	2024/01/16 - 22:33:46.001
	Priority	00	HIGH
	Longitude	E4 2C C9 08	-466827000
	Latitude	F1 F4 75 CC	-235637300
	Altitude	00 00	0
	Angle	00 00	0
	Satellites	03	3
	Speed	00 00	0
	Event IO ID	2A 4C	10828
	N of Total ID	00 01	1
	N1 of One Byte IO	00 00	0
	N2 of Two Bytes IO	00 00	0
	N4 of Four Bytes IO	00 00	0
	N8 of Eight Bytes IO	00 00	0
	NX of X Bytes IO	00 01	1
	N’th IO ID - AVL ID.	2A 4C	10828
	Length of Variable Length IO	00 14	20
	Value of Variable Length IO	01 12 00 01 E5 0F 06 7C D9 F4 01 EF 77 0D 01 00 0E 02 0B FE
AVL DATA	Timestamp	00 00 01 8D 14 68 C1 25	2024/01/16 - 22:33:46.001
	Priority	00	0
	Longitude	E4 2C C9 08	-466827000
	Latitude	F1 F4 75 CC	-235637300
	Altitude	00 00	0
	Angle	00 00	0
	Satellites	03	3
	Speed	00 00	0
	Event IO ID	2A 4D	10829
	N of Total ID	00 01	1
	N1 of One Byte IO	00 00	0
	N2 of Two Bytes IO	00 00	0
	N4 of Four Bytes IO	00 00	0
	N8 of Eight Bytes IO	00 00	0
	NX of X Bytes IO	00 01	1
	N’th IO ID - AVL ID.	2A 4D	10829
	Length of Variable Length IO	00 14	20
	Value of Variable Length IO	01 12 00 01 C8 0F 06 7C D9 F4 02 55 BE 0D 01 00 0E 02 0B F4
AVL DATA	Timestamp	00 00 01 8D 14 68 C1 2F	2024/01/16 - 22:33:46.001
	Priority	00	0
	Longitude	E4 2C C9 08	-466827000
	Latitude	F1 F4 75 CC	-235637300
	Altitude	00 00	0
	Angle	00 00	0
	Satellites	03	3
	Speed	00 00	0
	Event IO ID	2A 4F	10831
	N of Total ID	00 01	1
	N1 of One Byte IO	00 00	0
	N2 of Two Bytes IO	00 00	0
	N4 of Four Bytes IO	00 00	0
	N8 of Eight Bytes IO	00 00	0
	NX of X Bytes IO	00 01	1
	N’th IO ID - AVL ID.	2A 4F	10831
	Length of Variable Length IO	00 14	20
	Value of Variable Length IO	01 12 00 01 B9 0F 06 7C D9 F4 00 4B 49 0D 01 00 0E 02 0B FE
	Number of Data 2 (Number of Total Records)	03	20
	CRC-16	00 00 86 BA

Near example (AVL ID - 10828)


nEAR BEACONS (AVL ID - 10828)
01120001E50F067CD9F401EF770D01000E020BFE


AVL Data Packet
AVL Data Packet Part	HEX Code Part	Decoded
Protocol ID	01
Data Length	12	18
Parameter ID	00	Beacon RSSI Level
Parameter Data Length	01	1
Parameter Data	E5	-27
Parameter ID	0F	EYE Sensor MAC address
Parameter Data Length	06	6
Parameter Data	7C D9 F4 01 EF 77	7CD9F401EF77
Parameter ID	0D	EYE Sensor Low Battery
Parameter Data Length	01	1
Parameter Data	00	0
Parameter ID	0E	EYE Sensor Battery Voltage
Parameter Data Length	02	2
Parameter Data	0B FE	3070

Away example (AVL ID - 10829)


AWAY BEACONS (AVL ID - 10829)
01120001C80F067CD9F40255BE0D01000E020BF4


AVL Data Packet
AVL Data Packet Part	HEX Code Part	Decoded
Protocol ID	01
Data Length	12	18
Parameter ID	00	Beacon RSSI Level
Parameter Data Length	01	1
Parameter Data	C8	-56
Parameter ID	0F	EYE Sensor MAC address
Parameter Data Length	06	6
Parameter Data	7C D9 F4 02 55 BE	7CD9F40255BE
Parameter ID	0D	EYE Sensor Low Battery
Parameter Data Length	01	1
Parameter Data	00	0
Parameter ID	0E	EYE Sensor Battery Voltage
Parameter Data Length	02	2
Parameter Data	0BF4	3060

Lost example (AVL ID - 10831)


LOST BEACONS (AVL ID - 10831)
01120001E50F067CD9F401EF770D01000E020BFE


AVL Data Packet
AVL Data Packet Part	HEX Code Part	Decoded
Protocol ID	01
Data Length	12	18
Parameter ID	00	Beacon RSSI Level
Parameter Data Length	01	01
Parameter Data	B9	-71
Parameter ID	0F	EYE Sensor MAC address
Parameter Data Length	06	6
Parameter Data	7C D9 F4 00 4B 49	7CD9F4004B49
Parameter ID	0D	EYE Sensor Low Battery
Parameter Data Length	01	1
Parameter Data	00	0
Parameter ID	0E	EYE Sensor Battery Voltage
Parameter Data Length	02	2
Parameter Data	0BFE	3070

Parsing for Lost & Found Feature

Visible Beacons (AVL ID - 10828)


LOST & FOUND FEATURE
Received data in hexadecimal stream: 00000000000000678E010000018D1459964B00E42CA472F1F5B94D00000000000000 2A4C0001000000000000000000012A4C003A01120001D60F067CD9F40255BE0D01000E020BF4120001E00F067CD9F4004B490D01000E020BFE120001AC0F067CD9F401EF770D01000E020BFE 0100001ACD


AVL Data Packet
AVL Data Packet Part		HEX Code Part	Decoded
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 67	103
	Codec ID	8E	142
	Number of Data 1 (Number of Total Records)	01	1
AVL DATA	Timestamp	00 00 01 8D 14 59 96 4B	2024/01/16 - 22:17:12.001
	Priority	00	0
	Longitude	E4 2C A4 72	-466827000
	Latitude	F1 F5 B9 4D	-235637300
	Altitude	00 00	0
	Angle	00 00	0
	Satellites	00	0
	Speed	00 00	0
	Event IO ID	2A 4C	10828
	N of Total ID	00 01	1
	N1 of One Byte IO	00 00	0
	N2 of Two Bytes IO	00 00	0
	N4 of Four Bytes IO	00 00	0
	N8 of Eight Bytes IO	00 00	0
	NX of X Bytes IO	00 01	1
	N’th IO ID - AVL ID.	2A 4C	10828
	Length of Variable Length IO	00 3A	58
	Value of Variable Length IO	01120001D60F067CD9F40255BE0D01000E020BF4 120001E00F067CD9F4004B490D01000E020BFE 120001AC0F067CD9F401EF770D01000E020BFE
	Number of Data 2 (Number of Total Records)	01	1
	CRC-16	00 00 1A CD


vISIBLE BEACONS (AVL ID - 10828)
01120001D60F067CD9F40255BE0D01000E020BF4 120001E00F067CD9F4004B490D01000E020BFE 120001AC0F067CD9F401EF770D01000E020BFE


AVL Data Packet
AVL Data Packet Part		HEX Code Part	Decoded
	Protocol ID	00 00 00 00
EYE BEACON 1	Data Length	12	18
	Parameter ID	00	Beacon RSSI Level
	Parameter Data Length	01	1
	Parameter Data	D6	-42
	Parameter ID	0F	EYE Sensor MAC address
	Parameter Data Length	06	6
	Parameter Data	7CD9F40255BE	7CD9F40255BE
	Parameter ID	0D	EYE Sensor Low Battery
	Parameter Data Length	01	1
	Parameter Data	00	0
	Parameter ID	0E	EYE Sensor Battery Voltage
	Parameter Data Length	02	2
	Parameter Data	0B F4	3060
EYE BEACON 2	Data Length	12	18
	Parameter ID	00	Beacon RSSI Level
	Parameter Data Length	01	1
	Parameter Data	E0	-32
	Parameter ID	0F	EYE Sensor MAC address
	Parameter Data Length	06	6
	Parameter Data	7CD9F4004B49	7CD9F4004B49
	Parameter ID	0D	EYE Sensor Low Battery
	Parameter Data Length	01	1
	Parameter Data	00	0
	Parameter ID	0E	EYE Sensor Battery Voltage
	Parameter Data Length	02	2
	Parameter Data	0B FE	3070
EYE BEACON 3	Data Length	12	18
	Parameter ID	00	Beacon RSSI Level
	Parameter Data Length	01	1
	Parameter Data	AC	-32
	Parameter ID	0F	EYE Sensor MAC address
	Parameter Data Length	06	6
	Parameter Data	7CD9F401EF77	7CD9F401EF77
	Parameter ID	0D	EYE Sensor Low Battery
	Parameter Data Length	01	1
	Parameter Data	00	0
	Parameter ID	0E	EYE Sensor Battery Voltage
	Parameter Data Length	02	2
	Parameter Data	0B FE	3070

Lost Beacons (AVL ID 10831)


LOST & FOUND FEATURE
Received data in hexadecimal stream: 00000000000000418E010000018D145CF59300E42CA472F1F5B94D00000000000000 2A4F0001000000000000000000012A4F001401120001AB0F067CD9F401EF770D01000E020BFE010000CBD8


AVL Data Packet
AVL Data Packet Part		HEX Code Part	Decoded
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 41	65
	Codec ID	8E	142
	Number of Data 1 (Number of Total Records)	01	1
AVL DATA	Timestamp	00 00 01 8D 14 5C F5 93	2024/01/16 - 22:20:53.001
	Priority	00	0
	Longitude	E4 2C A4 72	-466827000
	Latitude	F1 F5 B9 4D	-235637300
	Altitude	00 00	0
	Angle	00 00	0
	Satellites	00	0
	Speed	00 00	0
	Event IO ID	2A 4F	10831
	N of Total ID	00 01	1
	N1 of One Byte IO	00 00	0
	N2 of Two Bytes IO	00 00	0
	N4 of Four Bytes IO	00 00	0
	N8 of Eight Bytes IO	00 00	0
	NX of X Bytes IO	00 01	1
	N’th IO ID - AVL ID.	2A 4F	10831
	Length of Variable Length IO	00 14	20
	Value of Variable Length IO	01120001AB0F067CD9F401EF770D01000E020BFE
	Number of Data 2 (Number of Total Records)	01	1
	CRC-16	00 00 CB D8


lOST BEACONS (AVL ID - 10831)
01120001AB0F067CD9F401EF770D01000E020BFE


AVL Data Packet
AVL Data Packet Part		HEX Code Part
Protocol ID	01
Data Length	12	18
Parameter ID	00	Beacon RSSI Level
Parameter Data Length	01	1
Parameter Data	AB	-85
Parameter ID	0F	EYE Sensor MAC address
Parameter Data Length	06	6
Parameter Data	7CD9F401EF77	7CD9F401EF77
Parameter ID	0D	EYE Sensor Low Battery
Parameter Data Length	01	1
Parameter Data	00	0
Parameter ID	0E	EYE Sensor Battery Voltage
Parameter Data Length	02	2
Parameter Data	0B FE	3070

Found Beacons (AVL ID - 10829)


LOST & FOUND FEATURE
Received data in hexadecimal stream: 00000000000000418E010000018D1464ECA300E42CD682F1F4768402B1005A050003 2A4D0001000000000000000000012A4D001401120001D60F067CD9F401EF770D01000E020BFE010000E720


AVL Data Packet
AVL Data Packet Part		HEX Code Part	Decoded
	Zero Bytes	00 00 00 00
	Data Field Length	00 00 00 41	65
	Codec ID	8E	142
	Number of Data 1 (Number of Total Records)	01	1
AVL DATA	Timestamp	00 00 01 8D 14 64 EC A3	2024/01/16 - 22:29:35.001
	Priority	00	0
	Longitude	E4 2C D6 82	-466827000
	Latitude	F1 F4 76 84	-235637300
	Altitude	02 B1	689
	Angle	00 5A	90
	Satellites	05	5
	Speed	00 03	3
	Event IO ID	2A 4D	10829
	N of Total ID	00 01	1
	N1 of One Byte IO	00 00	0
	N2 of Two Bytes IO	00 00	0
	N4 of Four Bytes IO	00 00	0
	N8 of Eight Bytes IO	00 00	0
	NX of X Bytes IO	00 01	1
	N’th IO ID - AVL ID.	2A 4D	10829
	Length of Variable Length IO	00 14	20
	Value of Variable Length IO	01120001D60F067CD9F401EF770D01000E020BFE
	Number of Data 2 (Number of Total Records)	01	1
	CRC-16	00 00 E7 20


FOUND BEACONS (AVL ID - 10829)
01120001D60F067CD9F401EF770D01000E020BFE


AVL Data Packet
AVL Data Packet Part		HEX Code Part
Protocol ID	01
Data Length	12	18
Parameter ID	00	Beacon RSSI Level
Parameter Data Length	01	1
Parameter Data	D6	-42
Parameter ID	0F	EYE Sensor MAC address
Parameter Data Length	06	6
Parameter Data	7CD9F401EF77	7CD9F401EF77
Parameter ID	0D	EYE Sensor Low Battery
Parameter Data Length	01	1
Parameter Data	00	0
Parameter ID	0E	EYE Sensor Battery Voltage
Parameter Data Length	02	2
Parameter Data	0B FE	3070

Sensor advertising and EYE Sensor Protocol overview

Beacon and sensors data

Protocol description

At the highest-level Bluetooth® LE advertising packet consists of Advertising Indication and Scan Response. Both packets can be maximum of 31 bytes in size. Advertising Indication packet is always broadcasted when Scan Response is broadcasted only if Observer device requests it by using Active Scan.

BTSMP1 uses Advertising Indication to send beacon data which can be configured to select between iBeacon and Eddystone protocols or to be disabled at all. In that case, data which is shown as Scan Response in protocol overview will be sent as Advertising Indication without Scan Response following it.

Scan Response is used to send device name and manufacturer specific data. Manufacturer specific data includes Teltonika Company ID (0x089A) and protocol version (0x01). It is followed by Flag Encoded Data (Table 1) and Extended Data (Table 2). Later on, protocol will be highly configurable in and will allow to disable/enable sending of device name or any sensor value allowing to reduce size of the packet being sent.

Teltonika BTSX devices are transmitting one or two packets depending on the selected protocol. Broadcast packet + Scan response packet.

A scan response packet is sent when an active scan is used, within the BLE layer of communication. The default for our FM devices and many other applications for example our EYE Appication or nRF connect Application is an active scan.

There are three protocols, with the following packets:

1.iBeacon + EYE Sensors

2.Eddystone + EYE Sensors

For iBeacon + EYE Sensors and Eddystone + EYE Sensors protocols only iBeacon/Eddystone packet is broadcasted and will be seen by both active and passive scans, to see the EYE Sensors packet you need to use an active scan. In other words in an environment where no BLE devices are scanning with an active scan or in case when there are no scanning devices at all, only the iBeacon/Eddystone packet will be sent by the BTS device to conserve energy.

3. EYE Sensors

With EYE Sensors protocol, the EYE Sensor packet becomes broadcast. In other words, in an environment where no BLE devices are scanning with an active scan or in case when there are no scanning devices at all EYE Sensors packet will be sent by the BTS device.

More Information on Active vs passive scans

Device Name has the following default value for Beacon – ID1_XXXXXXX

**Table 1. Flag Encoded Date**
Data	Size (Bytes)	Description
Flags	1	Each set bit (0-7) means the presence of value (0-7). Bits: 0 – Temperature value presence 1 – Humidity value presence 2 – Magnetic sensor presence 3 – Magnetic sensor state (1 magnetic field is detected/0 magnetic field is not detected) Valid value is present only if bit 2 flag is set. 4 – Movement sensor counter 5 – Movement sensor angle 6 – Low Battery indication (if set to 1 low battery voltage detected) 7 – Battery voltage value presence
Value 0	2	Temperature Value in Celsius / 100 NOTE: present only if bit 0 is set, otherwise is not being sent
Value 1	1	Humidity Value in percent NOTE: present only if bit 1 is set, otherwise is not being sent
Value 2	2	Movement Sensor counter Most significant bit indicates movement state and 15 least significant bits represent count of movement events. NOTE: present only if bit 4 is set, otherwise is not being sent
Value 3	3	Movement sensor angle Most significant byte – pitch (-90/+90) Two least significant bytes – roll (-180/+180) NOTE: present only if bit 5 is set, otherwise is not being sent
Value 4	1	Battery Voltage Battery voltage in mV = 2000 + VALUE * 10 NOTE: present only if bit 7 is set, otherwise is not being sent

GATT Characteristics

Name	Service UUID	Characteristic UUID	Data Type	Min	Max	Default Value	Notes
Device Name	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0016-7df2-4d4e-8e6d-c611745b92e9	ASCII	0	12	Unique for each device	-
Tx Power Lever	1804	2a07	SINT8	-14	8	2	Possible values: -14, -11, -8, -5, -2, 2, 4, 8
Protocol Type	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0001-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	4* *Max 2 with 01.02.10+ firmware	1 for EYE_Beacon, 4 for EYE_Sensor* *with 01.02.10+ firmware 1 for both EYE_Beacon & EYE_Sensor	0 - iBeacon 1 - Eddystone 2 - EYE Sensor 3 - iBeacon + EYE Sensor* 4 - Eddystone + EYE Sensor* 01.02.10+ sensors are enabled over Activate / Deactivate Sensors*
Activate / Deactivate Sensors* *from 01.02.10+ firmware	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0021-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	15 (0b1111)	4 (0b0100) for EYE_Beacon, 15 (0b1111) for EYE_Sensor	(LSb) bit 0 – Temperature Bit 1 – Humidity Bit 2 – Magnetic Bit 3 - Movement E.g. EYE_Sensor disabled movement & enabled temperature, humidity, magnetic sensors 7 (0b0111)
Advertising Interval	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0002-7df2-4d4e-8e6d-c611745b92e9	UINT16	1000	10000	5000	miliseconds
Sub Advertising Interval	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0003-7df2-4d4e-8e6d-c611745b92e9	UINT16	20	1000	100	Used by repeats, miliseconds
Advertising Repeats	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0004-7df2-4d4e-8e6d-c611745b92e9	UINT16	1	10	1	Repeats work only if Advertising Interval is more than 2000 ms and Repeats set to more than 1
iBeacon ID	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0005-7df2-4d4e-8e6d-c611745b92e9	BYTE ARRAY	20 bytes	20 bytes	Unique for each device	16 B - UUID 2 B - major 2 B - minor
Eddystone ID	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0006-7df2-4d4e-8e6d-c611745b92e9	BYTE ARRAY	16 bytes	16 bytes	Unique for each device	10 B - Namespace 6 B - Instance
Command	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0007-7df2-4d4e-8e6d-c611745b92e9	Command characteristic
Password	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0008-7df2-4d4e-8e6d-c611745b92e9	BYTE ARRAY	6 bytes	6 bytes	123456	Always 6 Digits
Sensor Interval	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0009-7df2-4d4e-8e6d-c611745b92e9	UINT16	0	10000	1000	miliseconds
Event Interval	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c000a-7df2-4d4e-8e6d-c611745b92e9	UINT16	0	10000	1000	miliseconds
Event Duration	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c000b-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	30	30	seconds
Temperature Event	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c000c-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	2	2	0 - on entrance 1 - on exit 2 - no event
Temperature Low	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c000d-7df2-4d4e-8e6d-c611745b92e9	INT8	-40	85	-20	celsius
Temperature High	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c000e-7df2-4d4e-8e6d-c611745b92e9	INT8	-40	85	50	celsius
Humidity Event	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c000f-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	2	2	0 - on entrance 1 - on exit 2 - no event
Humidity Low	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0010-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	100	15	%
Humidity High	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0011-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	100	50	%
Movement Event	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0012-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	2	2	0 - on entrance 1 - on exit 2 - no event
Movement Start	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0013-7df2-4d4e-8e6d-c611745b92e9	UINT16	0	300	5	seconds
Movement Stop	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0014-7df2-4d4e-8e6d-c611745b92e9	UINT16	0	300	5	seconds
Magnetic Event	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0015-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	2	2	0 - on entrance 1 - on exit 2 - no event
Password Counter	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0019-7df2-4d4e-8e6d-c611745b92e9	UINT8	0 (counter)	10 (counter)	0	Byte 0 – counter, Byte 1 and 2 - timeout
Master Password (PUK)	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0020-7df2-4d4e-8e6d-c611745b92e9	UINT8	8 bytes	8 bytes	MAC address dependency	Byte array
Manufacturer sleep (Hibernate mode)	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0018-7df2-4d4e-8e6d-c611745b92e9	UINT8	0	1	1	0 – sleep disabled, 1 – sleep enabled
User ADV Spam Duration	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0022-7df2-4d4e-8e6d-c611745b92e9	UINT16	1	300	30	WakeUp Advertising Spam Duration in seconds
RSSI Calibration Value	e61c0000-7df2-4d4e-8e6d-c611745b92e9	e61c0023-7df2-4d4e-8e6d-c611745b92e9	INT8	-100	127	127	RSSI value in dBm 127 – Use default calib. table
Manufacturer	180A	2A29	BYTE ARRAY	-	-	Not Configurable	Read Only. Ex. "Teltonika"
Model	180A	2A24	BYTE ARRAY	-	-	Not Configurable	Read Only. Ex. "BTSID1"
Serial	180A	2A25	BYTE ARRAY	-	-	Not Configurable	Not used
Hardware	180A	2A27	BYTE ARRAY	-	-	Not Configurable	Read Only. Ex. "Table:1 Volt:325
Firmware	180A	2A26	BYTE ARRAY	-	-	Not Configurable	Read Only. Ex. "1.1.0-beta"
System ID	180A	2A23	BYTE ARRAY	-	-	Not Configurable	Not used
MAC	180A	652143dc-dec6-4fb1-bd46-3e919d2410a6	BYTE ARRAY	6	6	Not Configurable	Read Only. ex. 112233445566 -> 11:22:33:44:55:66
Scan Response Data	e61c0000-7df3-4d4e-8e6d-c611745b92e9	e61c0001-7df3-4d4e-8e6d-c611745b92e9	BYTE ARRAY	17	17	Not Configurable	Scan Response Data, see picture for detail view of data structure

Command characteristic

Command's name	Data to send	Description
Write to flash	0x0010	Writes set parameters to flash
General boot	0x0011	Enter boot mode
Instant reset	0x0012	Software reset
Reset after connection	0x0013	Reset after disconnect
Get hw voltage	0x0014	Sets detected hw voltage in response data
Keep connection alive	0x0015	Resets disconnect timer
Restore defaults	0x0016	Sets all configurable parameters to default values

EYE Sensor Bluetooth® frame parsing example


Unparsed data
0201061AFF4C000215FFFFFFFF0B8C404510C655AAB636EBEFBB700055020C094D50315F313233343536370EFF9A0801B708B4120CCB0BFFC767


Parsed data
Parameter		HEX Code Part	Actual Value
	Length	02
	Type	01
	Flags	06
	Length	1A
	Type	FF
	Apple company identifier (big endian)	4C00
	Beacon type	0215
	UUID	FFFFFFFF0B8C404510C655AAB636EBEF
	Major	BB70
	Minor	0055
	Power	02
	Length	0C
	Type	09
	Device name	4D50315F31323334353637
	Length	0E
	Type	FF
	Teltonika company ID (big endian)	9A08
	Protocol version	01
	Flags	B7	Raw value example 0xB7. Data has to be interpretated as binary value. In this example would be (MSB)1011 0111(LSB) and is parsed from least significant byte(LSB). 0 – Temperature value presence. 1 Means device is reading and transmitting temperature value. 1 – Humidity value presence. 1 Means device is reading and transmitting humidity value. 2 – Magnetic sensor presence. 1 Means device is reading and transmitting Magnetic sensor value. 3 – Magnetic sensor state (1 magnetic field is detected/0 magnetic field is not detected) Valid value is present only if bit 2 flag is set. 4 – Movement sensor counter. 1 Means device is reading and transmitting movement state and count values. 5 – Movement sensor angle. 1 Means device is reading and transmitting angle roll and pitch values. 6 – Low Battery indication. 0 – Means device battery is from 100 to 15 % (When value changes to 1 Battery level is lower than 15 %. 7 – Battery voltage value presence. 1 Means device is reading and transmitting battery voltage value.
	Temperature	08B4	Raw value example 0x08B4 hex, 2228 dec. Raw value needs to be divided by 100. Real temperature is 22,28 Celsius.
	Humidity	12	Raw value example 0x12 hex, 18 dec. Decimal value is humidity in percent. Humidity 18 %
	Movement	0CCB	(MSB)0000 1100 1100 1011(LSB) binary 0 - Most significant byte(MSB) represents Movement status. In this case device is not moving 0. If it was 1 device is moving. 000 1100 1100 1011 – represent detected movements count 3275 decimal value means device has detected total 3275 movement events,
	Angle	0BFFC7	0B – Most significant byte represents device pitch. Device pitch can be from -90 to 90 degrees. In this example device pitch is 0000 1011 (2's complement) = 11° degrees. FFC7– Two least significant bytes represent device roll. Device roll can be from -180 to 180 degrees. In this example device Roll is 1111 1111 1100 0111 (2's complement) = -57° degrees
	Battery voltage	67	Battery voltage – raw value example 0x67 hex. Decimal value of parameter 103. To calculate battery voltage need to use calculation 2000 + (VALUE * 10). In this case battery voltage value 2000+(103x10)= 3030 mV

Safety information

This message contains information on how to operate BTSID1 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

1. To avoid mechanical damage, it is advised to transport the device in an impact-proof package.

2. In case of malfunction contact your Teltonika account manager or write to the technical support team over the Helpdesk.

Certification & Approvals


Certificates	Links
E-Mark (EU)	Yes
FCC (USA)	Yes
CE/RED (EU)	Yes
RoHS (EU)	Yes
REACH (EU)	Yes
Anatel (EU) (PR)	Yes
IP rating	Yes
SIRIM QAS	Yes
SDPPI POSTEL	Yes
TELEC	Yes
ATEX	Yes

Nomenclature & Classification codes


Name	Links
EAN	Yes
HS	Yes

Memberships


Name	Links
Bluetooth® SIG	Yes
WEEE	Yes

External Links

Product Page

https://teltonika-gps.com/eye/

Product Change Notifications

The latest Product Change Notifications can be found: Product Change Notifications

Software Errata

Firmware Errata: BTS firmware errata

EYE App Errata: BTS APP errata

Promotional Material

EYE Sensor Promotional Material

Compatibilty with other Teltonika Devices

Teltonika Networks: https://wiki.teltonika-networks.com/view/Bluetooth_EYE_Sensor_and_EYE_Beacon_support

Partner Providers Supporting Software

Frequently asked questions (FAQ)

Documents

Datasheet PDF (EN)

(Updated on: 2024-01-16)

BTSMP1 Quick Manual (EN)

(Updated on: 2024-01-17)

North America Flyer

(Updated on: 2023-03-13)

@@ Line 8: / Line 8: @@
 ==<p style="font-size:32px"><span style="color:#0054A6">Product Specification</span></p>==
 <div class="mw-collapsible-content">
-==<p style="font-size:24px"><span style="color:#0054A6">Features</span>==
+<div class="mw-collapsible mw-collapsed">
+===<p style="font-size:24px><span style="color:#0054A6">Features</span>===
+<div class="mw-collapsible-content">
 {| class="wikitable"
 |+
@@ Line 111: / Line 113: @@
 | style="width:10%;border: 1px solid white; border-bottom: 2px solid #E8E8E8; text-align: left; vertical-align: center; background: white;" |Yes
 |}
+</div>
+</div>
+<div class="mw-collapsible mw-collapsed">
 ===<p style="font-size:24px><span style="color:#0054A6">Dimensions</span>===
+<div class="mw-collapsible-content">
 [[File:Eye dimensions.png]]
+</div>
+</div>
 </div>
 </div>

Search