Difference between revisions of "FMB640 SMS/GPRS command list"
From Wiki Knowledge Base | Teltonika GPS
Line 142: | Line 142: | ||
|} | |} | ||
− | {{{sect_can|{{Template: | + | {{{sect_can|{{Template:FMB640 CAN SMS/GRPS commands}}}}} |
Revision as of 07:00, 29 May 2018
Main Page > EOL Products > FMB640 > FMB640 Manual > FMB640 SMS/GPRS command list
All commands are case sensitive. When user tries to send SMS/GPRS message to FMB640 that operates in Deep Sleep mode, it cannot arrive to FMB640 device because the GSM/GPRS module is disabled most of the time. FMB640 will receive the SMS/GPRS message when it exits Deep Sleep mode.
If FMB640 is in GPS Sleep or Online Deep Sleep mode, sent SMS/GPRS message will arrive to the device.
Common commands
Command | Description | Response |
---|---|---|
getstatus | Modem Status information. | Yes |
getcfgtime | Date and Time of last successful configuration | Yes |
getgps | Current GPS data and time | Yes |
getnmeainfo | Nmea error debug sms. | Yes |
cpureset | Reset CPU. | Yes |
resetallprof | Reset profile FLASH to default. | Yes |
getver | Device / Modem / Code version information. | Yes |
getinfo | Device runtime system information. | Yes |
deleterecords | Delete all records saved on FLASH. | Yes |
getio | Readout digital inputs and outputs, analog inputs. | Yes |
banlist | Banlist information. | Yes |
crashlog | Crash log information. | Yes |
delete_all_sms | Delete all read SMS. | Yes |
braminfo | BatRam info. | Yes |
getgnss | Current GNSS information. | Yes |
resetlimits | Resets data counters. | Yes |
readio # | Enable/disable static navigation. | Yes |
setdigout XXXX Y1 Y2 Y3 Y4 | Set digital output. 1. # – 0 or 1 (0 - OFF or 1 – ON) for DOUT1. 2. # – 0 or 1 (0 - OFF or 1 – ON) for DOUT2. 3. # – 0 or 1 (0 - OFF or 1 – ON) for DOUT3. 4. # – 0 or 1 (0 - OFF or 1 – ON) for DOUT4. Y1 – timeout value for DOUT1 if needed (in seconds). Y2 – timeout value for DOUT2 if needed (in seconds). Y3 – timeout value for DOUT3 if needed (in seconds). Y4 – timeout value for DOUT4 if needed (in seconds). |
Yes |
getparam # | Readout parameter value according entered ID. # - ID value. |
Yes |
setparam #:# | Sets selected parameter value. 1.# - first ID value. |
Yes |
setparam #:#;#:#;… | ||
flush #,#,#,#,#,#,# | Redirects device to other server. 1.# - IMEI. |
Yes |
Command | Description | Response |
---|---|---|
odoset:# | Set total odometer value. # - new odometer value in km. |
Yes |
odoget | Display current odometer value. | Yes |
Command | Description | Response |
---|
Command | Description | Response |
---|---|---|
lvcansetprog # | Set program number to LV-CAN200/ ALL-CAN300 that is connected to FMx640. # - three digit number that identity vehicle | Yes |
lvcansimpletacho # | Add or remove simpletacho start byte. # - 0 or 1 (0 – don’t add start byte, 1 – add start byte) | No |
lvcangetprog | Get program number from LV-CAN200/ ALL-CAN300 that is connected to FMx640 | Yes |
lvcangetinfo | Get information about connected LV-CAN200/ALL-CAN300 | Yes |
lvcanclear # | Clear Total Mileage (counted), Engine Work Time (counted), Fuel Consumed (counted) parameters values. # - parameter (0 – Engine work time (counted), 1 – Fuel Consumed (counted), 2 – Vehicle Mileage (counted)) | Yes |