Difference between revisions of "Template:FMT1 Mounting recommendations"

From Wiki Knowledge Base | Teltonika GPS
Line 1: Line 1:
−
<font size="+2"><span style=color:#104996>'''Mounting recommendations'''</span></font>
+
==<span style=color:#FF0000>'''Safety information'''</span>==
 +
This message contains information on how to operate {{{model|FMB1YX}}} safely. By following these requirements and recommendations, you will avoid any dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!
 +
*The device uses a 10 V...30 V DC power supply. The nominal voltage is 12 V DC. The allowed range of voltage is 10 V...30 V DC.
 +
*To avoid mechanical damage, it is advised to transport the {{{model|FMB1YX}}} device in an impactproof package.
 +
*Before dismounting the device from the vehicle, ignition '''MUST be OFF'''.
  
−
<font size="+2"><span style=color:#F49E21> 1. </span> Connecting wires </font>
+
==='''Precautions'''===
−
<font size="+1">
 
−
* Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
 
−
* The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
 
−
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
 
−
* Wires cannot be connected to the board computers or control units.
 
−
</font>
 
−
 
 
−
<font size="+2"><span style=color:#F49E21> 2. </span> Connecting power source. </font>
 
−
<font size="+1">
 
−
* Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in 5 to 30 minutes period.
 
−
* When module is connected, measure voltage again to make sure it did not decrease.
 
−
* It is recommended to connect to the main power cable in the fuse box.
 
−
* Use 3A, 125V external fuse.
 
−
</font>
 
−
 
 
−
<font size="+2"><span style=color:#F49E21> 3. </span> Connecting ignition wire. </font>
 
−
<font size="+1">
 
−
* Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
 
−
* Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
 
−
* Check if power is still available when you turn off any of vehicles devices.
 
−
* Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
 
−
</font>
 
−
 
 
−
<font size="+2"><span style=color:#F49E21> 4. </span> Connecting ground wire. </font>
 
−
<font size="+1">
 
−
* Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
 
−
* If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
 
−
* For better contact scrub paint from the spot where loop is going to be connected.
 
−
</font>
 
−
 
 
−
 
 
−
<font size="+2"><span style=color:#FF0000>'''Safety information'''</span></font><br/>
 
−
<font size="+1">
 
−
This message contains information on how to operate {{{model|FMB1YX}}} safely. By following these requirements and recommendations, you will avoid any dangerous situations.<br/>
 
−
You must read these instructions carefully and follow them strictly before operating the device! The device uses a 10 V... 30 V DC power supply. The nominal voltage is 12 V DC.<br/>
 
−
The allowed range of voltage is 10 V... 30 V DC. To avoid mechanical damage, it is advised to transport the {{{model|FMB1YX}}} device in an impactproof package.<br/>
 
−
Before dismounting the device from the vehicle, ignition must be off.<br/>
 
−
</font>
 
−
 
 
−
 
 
−
<font size="+2"><span style=color:#104996>'''Precautions'''</span></font>
 
−
<font size="+1">
 
 
{| class="wikitable" style="border-style: solid; border-width: 0px"
 
{| class="wikitable" style="border-style: solid; border-width: 0px"
 
|+  
 
|+  
 
|-
 
|-
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_nb.png|50px]]
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_nb.png|50px]]
−
| style="text-align: left; background: #F6F6FB;"        | Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
+
| style="text-align: left; background: #F6F6FB;"        | '''Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.'''
 
|-
 
|-
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_nb.png|50px]]
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_nb.png|50px]]
−
| style="text-align: left; background: #F6F6FB;"        | All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
+
| style="text-align: left; background: #F6F6FB;"        | '''All wireless data transferring devices produce interference that may affect other devices which are placed nearby.'''
 
|-
 
|-
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_key.png|50px]]
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_key.png|50px]]
−
| style="text-align: left; background: #F6F6FB;"        | The device must be connected only by qualified personnel.
+
| style="text-align: left; background: #F6F6FB;"        | '''The device must be connected only by qualified personnel.'''
 
|-
 
|-
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_tick.png|50px]]
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_tick.png|50px]]
−
| style="text-align: left; background: #F6F6FB;"        | The device must be firmly fastened in a predefined location.
+
| style="text-align: left; background: #F6F6FB;"        | '''The device must be firmly fastened in a predefined location.'''
 
|-
 
|-
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_tick.png|50px]]
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_tick.png|50px]]
−
| style="text-align: left; background: #F6F6FB;"        | The programming must be performed using a PC with autonomic power supply.
+
| style="text-align: left; background: #F6F6FB;"        | '''The programming must be performed using a PC with autonomic power supply.'''
 
|-
 
|-
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_humidity.png|50px]]
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_humidity.png|50px]]
−
| style="text-align: left; background: #F6F6FB;"        | The device is susceptible to water and humidity.
+
| style="text-align: left; background: #F6F6FB;"        | '''The device is susceptible to water and humidity.'''
 
|-
 
|-
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_ecute.png|50px]]
 
| style="text-align: left; background: #F6F6FB;"        | [[Image:Bw_ecute.png|50px]]
−
| style="text-align: left; background: #F6F6FB;"        | Installation and/or handling during a lightning storm is prohibited.
+
| style="text-align: left; background: #F6F6FB;"        | '''Installation and/or handling during a lightning storm is prohibited.'''
 
|}
 
|}
−
</font>
 

Revision as of 15:51, 24 October 2018

Safety information

This message contains information on how to operate FMB1YX safely. By following these requirements and recommendations, you will avoid any dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

  • The device uses a 10 V...30 V DC power supply. The nominal voltage is 12 V DC. The allowed range of voltage is 10 V...30 V DC.
  • To avoid mechanical damage, it is advised to transport the FMB1YX device in an impactproof package.
  • Before dismounting the device from the vehicle, ignition MUST be OFF.

Precautions

Bw nb.png Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
Bw nb.png All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
Bw key.png The device must be connected only by qualified personnel.
Bw tick.png The device must be firmly fastened in a predefined location.
Bw tick.png The programming must be performed using a PC with autonomic power supply.
Bw humidity.png The device is susceptible to water and humidity.
Bw ecute.png Installation and/or handling during a lightning storm is prohibited.
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=Template:FMT1_Mounting_recommendations&oldid=20418"