Difference between revisions of "How to capture CAN adapter log from FMX1YX"

From Wiki Knowledge Base | Teltonika GPS
m (Reverted edits by VytenisK (talk) to last revision by Airidas.S)
Tag: Rollback
Line 7: Line 7:
 
#'''Start vehicle engine'''.
 
#'''Start vehicle engine'''.
 
#Send following '''SMS commands''' to FMX1YX device:  
 
#Send following '''SMS commands''' to FMX1YX device:  
−
#*If you have set SMS login and password:<code>login pass sdformat</code><code>'''Note:'''this will delete all previous DUMP without filters logs and that have not been sent yet.</code>
+
#*If you have set SMS login and password:<code>login pass log2sdfilterset 0;4;1</code>  
−
#*If you have set SMS login and password:<code>login pass sdformat</code>
+
#*If SMS login and password are not set leave two spaces before command: <code><span style="color:#f8f9fa">aa</span>log2sdfilterset 0;4;1</code> <p>If command <code>log2sdfilterset</code> was sent correctly you should receive SMS Response:<code>Enabled Trace Filters:3</code> then you can restart the device</p>
−
#*If SMS login and password are not set leave two spaces before command: <code><span style="color:#f8f9fa">aa</span>log2sdfilterset 0;2;4;1</code>
 
−
#*If SMS login and password are not set leave two spaces before command: <code><span style="color:#f8f9fa">aa</span>log2sdfilterset 0;2;4;1</code> <p>If command <code>log2sdfilterset</code> was sent correctly you should receive SMS Response:<code>Enabled Trace Filters:4</code> then you can restart the device</p>
 
 
#*<p>If you have set SMS login and password: <code>login pass cpureset</code></p>
 
#*<p>If you have set SMS login and password: <code>login pass cpureset</code></p>
−
#*<p>If SMS login and password are not set leave two spaces before command:<code><span style="color:#f8f9fa">aa</span>cpureset</code></p><p>Filter description:</p><p>Filter 0 - default filters (No additional data)</p><p>Filter 2 -  turn on AVL record creation filter</p><p>Filter 4 - turn on CAN adapter filter</p><p>Filter 1 - save installed filters to memory after restart</p>
+
#*<p>If SMS login and password are not set leave two spaces before command:<code><span style="color:#f8f9fa">aa</span>cpureset</code></p><p>Filter description:</p><p>Filter 0 - default filters (No additional data)</p><p>Filter 4 - turn on CAN adapter filter</p><p>Filter 1 - save installed filters to memory after restart</p>
 
#After the SMS response message CAN adapter log capturing has been started.
 
#After the SMS response message CAN adapter log capturing has been started.
 
#Wait at least '''5 minutes''' to get enough CAN bus data and '''turn off''' vehicle engine.
 
#Wait at least '''5 minutes''' to get enough CAN bus data and '''turn off''' vehicle engine.

Revision as of 11:55, 22 December 2020

Main Page > Frequently Asked Questions - FAQ > How to capture CAN adapter log from FMX1YX

Solution applies for these devices

FMB110 FMB120 FMB122 FMB125 FMB140 FMC125 FMC130 FMM125 FMM130 FMC125 FMU126 FMU130

Here are steps how to capture LV-CAN200, ALL-CAN300, CAN-CONTROL log from FMB1YX series devices.

This functionality is available after 03.08.00 firmware version.

  1. Make sure that the CAN adapter is connected properly to the vehicle and to the FMB1YX series device.
  2. Start vehicle engine.
  3. Send following SMS commands to FMX1YX device:
    • If you have set SMS login and password:login pass log2sdfilterset 0;4;1
    • If SMS login and password are not set leave two spaces before command: aalog2sdfilterset 0;4;1

      If command log2sdfilterset was sent correctly you should receive SMS Response:Enabled Trace Filters:3 then you can restart the device

    • If you have set SMS login and password: login pass cpureset

    • If SMS login and password are not set leave two spaces before command:aacpureset

      Filter description:

      Filter 0 - default filters (No additional data)

      Filter 4 - turn on CAN adapter filter

      Filter 1 - save installed filters to memory after restart

  4. After the SMS response message CAN adapter log capturing has been started.
  5. Wait at least 5 minutes to get enough CAN bus data and turn off vehicle engine.
  6. Download captured log (dump) files.
    • Using Teltonika Configurator
      Dumpfilesfromcfg.gif

      Please check Status info→Maintenance→Log/Dump and download dump YYYY_MM_DD_HH_MM_SS_FMB1YX_IMEI_Dump.zip.

    • Using FOTA WEB

      FOTAWEB.gif

      Enter FOTA WEB → Press on Devices tab → Select your device and press Fota actions.png → Download from device → Continuous log files (2) (2 files. Each log size up to 1 MB)→Fota download.png. To start download process at once send following SMS command:

      • If you have set SMS login and password: login pass web_connect
      • If SMS login and password are not set leave two spaces before command: aaweb_connect

        If command was sent correctly you should receive SMS Response:web_connect resp:OK

        To find downloaded log press on device Fota moreinfo.png icon→Go to CONT.LOGS tab→Download IMEI_TIMESTAMP.zip

  7. After you have downloaded log files send following SMS command to FMX1YX device:
    • If you have set SMS login and password: login pass log2sdfilterset 0
    • If SMS login and password are not set leave two spaces before command: aalog2sdfilterset 0

      If command was sent correctly you should receive SMS Response:Enabled Trace Filters:1

  8. These log (dump) files can be read only with special software. Provide these files to your Teltonika Sales manager or Teltonika Support team for further investigation.
Retrieved from "https://wiki.teltonika-gps.com/index.php?title=How_to_capture_CAN_adapter_log_from_FMX1YX&oldid=61499"