From Wiki Knowledge Base | Teltonika GPS
|
CAUTION!
Both firmwares (Modem and BlueNRG) must be flashed into device. Failing so can lead to unexpected device behavior and rapid battery discharge.
|
TAT100 BlueNRG & Modem FIRMWARE UPDATE GUIDE
| TATXYZ FIRMWARE UPDATE GUIDE
|
Download Firmware and Configurator from STABLE FIRMWARE or SHORT-TERM FIRMWARE pages.
After device connection to Configurator:
1) Select Update firmware;
2) Select to flash Firmware(*.e.XIM) file;
3) Click on file;
4) And select Open.
Wait until the device will upload the firmware.
When parameters successfully loaded:
1) Select Update firmware;
2) Select to flash BlueNRG firmware(*.bin);
3) Click on file;
4) And select Open.
Backup/BLE support Feature Firmware
| SHORT-TERM FIRMWARE
|
| FIRMWARE VERSION:
|
Not Available
|
| CONFIGURATOR VERSION:
|
Not Available
|
| BlueNRG VERSION:
|
Not Available
|
RELEASE DATE:
|
Not Available
|
|
| On request via Teltonika HelpDesk
|
|
|
|
TAT100 Hardware version identification
|
- If Serial Number [S/N] is greater than 1122473261, then device version: TAT100 HW: 62.
- If Serial Number [S/N] is less than 1122473261, then device version: TAT100 HW: 31.
|
ORDERS AFTER 2022-03-17 WILL BE WITH TAT100 HARDWARE: 62
CAUTION!
|
When updating firmware via FOTA WEB, pay attention to notice above.
|
| NOTE!
|
THERE IS NO SHORT TERM FIRMWARE AVAILABLE. PLEASE USE THE STABLE VERSION.
|
CHANGELOG
| VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
KNOWN ISSUES
|
| N/A
|
N/A
|
N/A
|
N/A
|
N/A
|
| VERSION
|
RELEASE DATE
|
CONFIGURATOR CHANGES
|
FIRMWARE CHANGES
|
KNOWN ISSUES
|
Firmware version: 55.00.16.Rev.543*
BlueNRG version: 10.3.12 for TAT100 HW ver.: 31
0.3.12 for TAT100 HW ver.: 62
Configurator version: 1.7.16_E.TAT100.R23 RELEASE
*was approved as STABLE
|
2022.08.08
|
- Updated Teltonika Configurator version to set Central device default IMEI to 300000000000000
|
- SMS command created for getting device statistics
- Protection from writing other devices FW
- Added condition to prevent modem waking up at midnight if scheduler is configured
- Added reconfiguration mechanism that lets FW work with / without SMPS filterMissing
- Fixed issue of missing 4th sensor's data with Monitoring operand
- Fixed too frequent / unnecessary scans with all sensors configured as monitoring
- Fixed sensors scan starting with monitoring operand when Backup tracker is configured
- Backup tracker scan not starting right after
- Time synchronization every 24 hours
- Fixed LBS data sending issue
- New AVL ID 20015 for Modem UpTime (in seconds)
- Added response sending if recovery command is sent through GPRS
- The next periodic record after Recovery mode deactivation being sent with AVL ID 20012 - fixed
- Reduced EQ Core update frequency
- Fixed battery consumption issue when GSM is jammed.
- LED status changed from constant on to blinking mode to save the battery
|
|
Firmware version: 55.00.16.Rev.531
BlueNRG version: 10.3.6 for TAT100 HW ver.: 31
0.3.6 for TAT100 HW ver.: 62
Configurator version: 1.7.16_R.TAT100.R5
|
2022.04.14
|
- Added Recovery mode option
- Added I/O element of Recovery Mode
- Added more options of movement sensitivity threshold [50-1000mG]
|
- Added Recovery mode feature
- Implemented Recovery mode activation from the Backup tracking alarm
- Added EYE sensors support
- Fixed Minor bugs regarding the sensors
- Fixed Short period Recovery Mode records
- Extended Backup Tracker: Central device IMEI range
- Backup tracker: Scanning logic has been changed, scan duration is not configurable anymore, it is up to 60 seconds by default now.
- Implemented Record timestamp shift feature
|
- Sometimes sensor records are randomly generated when using Backup Tracking with the USB cable plugged in.
- Only 2 sensors are working correctly with Monitoring Operand, values from the 3rd and 4th sensor may not be received.
|
Firmware version: 55.00.16.Rev.522
BlueNRG version: 10.2.21.Rev.01
Configurator version: 1.7.16_R.TAT100.R2-BACKUP
|
2021.12.21
|
|
Backup firmware:
- Changed required packets amount in backup tracker scenario and minimal scan duration
- Fixed backup tracker alarm not triggering just before wakeup
- Fixed backup tracker not detecting enough packets during BLE scan
- Periodic records do not affect backup tracker alarm record generation
|
- Sometimes
Periodic/Schedule record overwrites backup alarm record if both records are created at a same time.
- Possible workaround would be to disable periodical records:
Tracking → Tracking Mode: None
|
Firmware version: 55.00.16.Rev.522
BlueNRG version: 10.2.21.Rev.01
Configurator version:
1.7.16_R.TAT100.R2-BLE
|
2021.12.21
|
|
BLE firmware:
- Fixed BLE sensor records with wrong event ID being sent
- Fixed BLE sensor record duplicates with
On change operand
- Fixed BLE sensor
On Exit record not generating when switching to sleep mode
- Fixed
Custom1 sensor data in SMS being sent as NaN (empty)
- Fixed duplicate BLE sensor data after waking up
|
|
Firmware version: 55.00.15.Rev.519
BlueNRG version: 10.2.14
Configurator version: 1.7.16_R.TAT100.R2-BACKUP
|
2021.10.19
|
|
- Fixed fake movement detection on startup
- Fixed problem when the device is stuck in On Stop tracking mode after reconfiguration
- Added Power-On reason data and fixed version changes to device statistics
- Fixed Backup tracker issue where the alarm mode is not immediately activated when the central device disappears
- Fixed empty GSM I/O elements
- Fixed an issue where UTC is added after each reconfiguration
- Added record printing to
Dump log
- LBS data is not included in records if GNSS fix was caught
- Fixed NTP timesync failure if offset is zero
- Improved record creation (wake up from sleep) during Backup tracker alarms
- Improved GNSS module control with
Static Navigation and LBS
- Added prevention from inappropriate record generation if the battery is low (HW watchdog)
- Added statistic element for USB connected uptime
- Added timestamp to BlueNRG serial prints
- Minor improvement for BlueNRG firmware update via configurator
- Added filter for
LBS cell_id duplicates
- Improved Bluetooth® sensor record creation with
'On Change' operand
- Added Bluetooth® sensor support
- Added condition to skip LBS data update if location source is only GNSS
- Increased retries of AT+# command in order to avoid empty LBS data from modem
- Changed
Open link timeout to 15s
- Fixed an issue where the tracking mode would change from the scheduler to periodic
- Improved logic for multiple
FOTA Web tasks update in the same connection
- Implemented rule for additional connection to
FOTA Web after baseband firmware update
- Added accelerometer version information inside '.info' serial command
- Fixed an issue with battery voltage
I/O element when record saving is overlapping with a firmware update
- Fixed
Scheduler record sending at midnight
- Fixed missed LBS values inside
I/O elements
- Fixed an issue when GNSS speed is not zero while the device is in a stationary position
- General minor improvements
|
|
|
