Main Page > Video Solutions > Teltonika ADAS > ADAS First Start

Main (front) camera unit preparation

The main unit comes prepared for bus/large truck setup (cable routing) or vehicles with mostly vertical windshields. To set up the unit for an average truck or passenger vehicle, dismantle partially as shown below:

Unit preparation
1. Remove cover 2. Remove (2x) screws,

remove plastic cover

3. Remove (2x) screws,

pry plastic mounting

frame off Unit from corners

4. Reroute the main

cable (and rear camera

cable, if adding) around unit

to front (glass side)

5. Press tightly into

channels when routing cables.

Remove front camera dust sticker

6. Replace 1 cover only

removed from step 3.

Replace 2 screws.

Leave the remaining

covers off until the last step

Vehicle installation

1. Clean the spots on the windshield with the alcohol wipe where you plan to mount the hardware. Remove the red 3M tape and mount the main unit underneath the rear-view mirror as centered (left/right) and straight as possible (if it must be off center by a few inches, that’s okay – measurements will be taken later). Be certain not to obstruct the drivers view.

 

2. Run the main-unit cable across the headliner and down to the driver side under-dash. This may require removing the A-pillar temporarily. Follow factory harnesses, always run behind any airbags.

3. Attach the mount (from the plastic bag) and stick the LCD indicator on the windshield in the driver’s line-of-sight, usually close to the A-pillar so it can be easily seen and controlled if required. Run this cable down to the driver’s under-dash as well.

 

4. Once both cables are run to the under-dash, connect them to the provided PCI unit at the proper ports.

  

5. Connect the Teltonika FMx125,FMX225 tracker to the main unit using RS232 cable. Please refer connection scheme below.

PIN NUMBER PIN NAME DESCRIPTION
4 RS232-Tx ADAS output for data transmission through RS232
3 RS232-Rx ADAS input for data reception through RS232
1 VCC (9-36V) (+) Power supply for the ADAS
7 GND (-) Ground

For FMX640 + ADAS connection

For FMX640 devices, RJ45 cable is required with one end cut and loose. Connect RJ45 cable to FMX640 device's port 1 or port 2, both slots have RS232 support. Once connected, the other end of the cable should have pin 3-Rx, 4-Tx shaved and connected to ADAS camera Rx and Tx cable. For the rest of the connection please refer to the picture below.

File:ADAS FMX640.png

PIN NUMBER PIN NAME DESCRIPTION
4 RS232-Tx ADAS output for data transmission through RS232
3 RS232-Rx ADAS input for data reception through RS232

6. Connect the provided Power/Ground harness connection to a chassis ground (black wire) and Ignition source (red wire). The circuit must provide ~3 Amp @12v. Connect the plug to the PCI unit at the ‘Power’ port.

 

Installation: for CAN-equipped vehicles

Many vehicles are available in database for using the CAN bus for vehicle signals (turn signals, brake and speed sense). This makes for a much faster installation. See below for checking availability of a downloadable CAN file for your vehicle. NOTE: not all vehicles are available on the database currently, even if the vehicle has CAN. The list is constantly updated, so if the vehicle isn’t there now, it may be later. The installation may still be completed using analog connections instead of CAN – see next section.

Check to see if there is a CAN file available by opening a Chrome browser and going to http://info.mdas.co.kr/customer/login

USER: [email protected]

PASS: mDaSdataBase

1. Choose the vehicle make and model into the selector at the left.

2. Click the page icon (at right) and the database information will show CAN wire location information (if available) and download the ‘CAN File Download’ file at the bottom. NOTE: this filename will always be ‘mdasinfo.dat’ and cannot be renamed – so if you’re installing another ADAS and using this computer to set up, make a separate file folder (every time) with the vehicle year and model, and put this file inside of it.


3. If there is a CAN file available, connect the provided CAN harness (contactless reader) to the (transmission) CAN bus wires – either where stated or at the OBD2 port, typically pins 14 & 6, if the vehicle is available on the database only.


NOTE: this connection uses inductance. There is no need to strip the CAN wires – just open the black box, lay the CAN High and Low in the channels, then close the box.

4. Connect the 4-pin plug from the CAN harness to the ‘CAN’ port on the PCI unit.

If the vehicle is not listed in database, you must use the provided Analog harness, see next section. NOTE: vehicles that are 1 year (or so) off, may still work for CAN access!

Installation: For Analog signals (no CAN)

If the vehicle has no CAN bus or there is no CAN file available, you must tap turn signal (left and right), brake and speed signal manually (various locations).

1. With a digital multimeter or test light, locate the brake signal wire that activates when the brake is pressed (vehicle may need to be ON). Connect and insulate the black/white wire to this vehicle’s wire. This may be a (+) or (-) signal.

2. With a digital multimeter or test light, locate the left turn signal wire that activates with the left turn signal. Connect and insulate the blue/white wire to this vehicle’s wire. This may be a (+) or (-) signal.

3. With a digital multimeter or test light, locate the right turn signal wire that activates with the right turn signal. Connect and insulate the blue wire to this vehicle’s wire. This may be a (+) or (-) signal.

4. Locate the VSS wire. Connect and insulate the brown/white wire to this vehicle’s wire.

NO other wires are required for typical installation – ground the remaining wires.

ADAS Calibration

ADAS Calibration requires:

  • a laptop with an internet connection and a browser
  • micro-USB cable
  • tape measure
  • parking the car with a clear, open stretch of about a 45 meters unobstructed view (try to park close to your facility to keep the internet connection accessible – at least during the calibration driver installation)
  • a partner to drive the vehicle while speed correction is performed

Before beginning, insert the provided micro-SD card into the main unit in the location shown below until it clicks and turn the Ignition ON. Wait for the prompt, then press and release the center button one time. After the successful prompt and the unit reboots, continue to step 1.

1. Park the vehicle in a spot with a clear stretch of unobstructed line-of-sight (about 45 meters). Leave the vehicle running

2. Connect the USB cable to the Mirco-USB port on the side of the main unit (windshield) and the other end to the laptop. If on a windows 10 machine, it should automatically install the required driver. If not or on an older machine, go to movon.co.kr, go to the ‘ADAS’ tab at the top then to ‘Downloads’ under Support. Download the appropriate zip file (contains driver) and extract it fully for your version of Windows OS (if using the 7/8 driver, install the .exe file). If WIN10, once downloaded, disconnect/reconnect the USB and it should automatically install, or find the unit in Device Manager and right-click, Update Driver and browse for driver locally.

3. Open Chrome browser again and type in ’10.0.0.1’ into the URL bar. If the driver was installed properly, the calibration screen will appear. Input credentials and press LOGIN USER:     admin PASS:     1234
4. Select Vehicle Signal Type: there are several wiring options for installation: CAN-BUS / Analog (GPIO) / GPS (Speed). Select the proper calibration option based off which was installed: CAN (if CAN file is available), Analog (if analog signals were tapped)

Vehicle Data File (CAN-BUS)For CAN-BUS connection, choose the ‘Vehicle info file’ tab and select ‘Choose File’ to upload the previously downloaded ‘mdasinfo.dat’ file (see ‘CAN-Equipped vehicles’ section).


ADAS and FMC640 Features

Periodic photo sending

Possible to receive periodical photo from ADAS

Video/photo by request

You can request video/photo from ADAS

ADAS Features

PCW (PEDESTRIAN COLLISION WARNING)

Notifies driver of any pedestrians, bicycles or motorcycles ahead.

LDW (LANE DEPARTURE WARNING)

Helps to regain direction if the driver unintentionally departs lanes.

FCW (FORWARD COLLISION WARNING)

Sends warning alerts if a crash is imminent to assist driver in maintaining a safe traveling distance.

FPW (FORWARD PROXIMITY WARNING)

Notifies driver if the vehicle moves forward while another vehicle is in the detection range, which can be setup at 1 m, 2 m, 3 meters.

FVSA (FRONT VEHICLE START ALARM)

Notifies driver if the front vehicle started moving forward from 0 speed without the vehicle moving within 2 secs.

SDA (SAFETY DISTANCE ALERT)

Attracts the driver's attention to keep the safe distance ahead by warning the driver (active from 30km/h).

DVR (DIGITAL VIDEO RECORDER)

Records scenes as HD+HD resolutions into SD card before and after an accident. (Every minute in a loop)

SLR (SPEED LIMIT RECOGNITION)

Recognizes speed limit signs and provides warnings for over speed (Available with ADAS Plus).

Product Specification


Technical data Description
Supported by FMB640, FMC640, FMB125, FMC125, FMB225, FMC225
Camera Resolution 1280 x 720 (HD)
View angle 30 (V), 52 (H), 60 (D)
Size 80 x 120 x 50 mm
SD card Max. 64GB
Video encoding H264

Electrical parameters Description
Input voltage range 9 – 36 V
Temperature -20 °C to +70 °C (operation) -40 °C to +85 °C (storage)
Relative Humidity Max. 90 %
Power consumption 12V max @300mA 12V Idle state @ 3mA

Interface Description
USB USB 2.0 (for calibration)
CAN CAN 2.0 (Car signal – Left/Right, Speed, RPM, Brake)
RS232 Indicator TX/RC (for communication with FM device)