NBL-3

Introduction to the product

Description:

Netronix NBL-3 -  wireless Bluetooth RFID reader with additional buttons.

NBL-3 is great in these use cases:

• Authorized driving - track who is driving your vehicle. You will receive a card ID every time a driver applies a card to NBL-3 reader.
• Private mode – this solution will allow your company car to be used by employees for personal purposes without violating the EU General Data Protection Regulations by masking all the personal data while vehicle is used in Private mode. Moreover, self-employed people can easily convert their own car into a business asset and ensure that the data provided (Example - distance traveled) is correct and shown only working hours' driven distance. Private/business mode can be easily switched by any of the NBL-3 buttons.

Features:

• Mifare® Classic, Desfire card supports
• Bluetooth low energy module
• Operating frequency - 13,56MHz
• Built in two LED indicators
• Built in two buttons
• UID and card DATA available
• Configure via BL link
• Firmware update via Bluetooth

Product Specification

Supply voltage	two AAA batteries
Sensor	Accelerometer Humidity Light Magnetic field Low battery voltage
Operating temperature	-20ºC to +70ºC
Size (mm)	100 x 58 x 18
Type	RFID reader

NBL-3 Configuration

For the NBL Tools application, contact the Netronix NBL manufacturer.

Updating NBL-3

How to update the NBL-3 device is shown in the link below.

https://netronix.pl/en/nbl-readers/nbl-3

Device configuration

This functionality is available from firmware version FMB.Ver.03.28.05.Rev.04

Setting up NBL-3 device to connect with FMB device.

Go to Teltonika configurator -> Bluetooth 4.0 and set it up like it shown in this screenshot (MAC address will depend on your particular NBL sensor):

Mandatory setting condition: Non Stop Scan

Then go to I/O settings:

Make sure to enable the BLE RFID #1 parameter (ID: 51740). We would recommend to set the operand to „On Change“.

Setting up Private/Business mode

Make sure to enable Private/Business mode in Trip/Odometer settings. It can be done using SMS commands or a configurator. Not every device has these parameters visible in the configurator, therefore they should be configured via SMS commands. It can be done by sending  setparam SMS (how to send SMS commands: https://wiki.teltonika-gps.com/view/FMB120_SMS/GPRS_Commands). Set it to High or Low priority (parameter ID: 11850). Enable triggers as NBL-1 Button1 or NBL-1 Button2 (parameter ID: 11811).

Don't forget to set up data masking in Private mode if necessary.

Don‘t forget to save all these changes to the device and you are ready to test the NBL-3 sensor.

More information about Private/Business Driving Mode Functionality.

NBL-3 packet

NBL-T data is being read via broadcast packets only. The packet structure is described below:

EIR Type	Description / Value	LEN
Flags – 0x01	0x06 GeneralDiscoverable, BrEdrNotSupported	3B
Complete name – 0x09	‘NBL-3’	7B
Service data – 0x16	Data format BYTE: 0..1 2 3 4..5 6..7 8 9 10..18 Field: UUID Status Batt Temp Humi Light CID_Len CID Field Description UUID ‘NX’ Status Data format: MSB LSB Prox Temp Humi Light Card 0 B1 B2 • Prox – state of magnetic field sensor • Motion – if 1, the measured temperature is outside the defined values • Motion – if 1, the measured humidity is outside the defined range • Light – if 1, the measured light is outside the definied range • Card – if 1, the ID is read • Btn1 – state of button 1 • Btn2 – state of button 2 Batt Battery level in % Temp Temperature Humi Humidity Light Light (8 oldest bits) CID_Len ID length CID ID card number	21B

Total packet length: 31B.