Changes

Line 85: Line 85:  
|}
 
|}
   −
==FMB120 ALL-CAN300 and LV-CAN200 parameters configuration==
+
=={{{model|FMB1YX}}} ALL-CAN300 and LV-CAN200 parameters configuration==
   −
Because FMB120 have LV-CAN200/ALL-CAN300 RX and TX in its own pinout, device configuration can be performed via micro-USB when CAN adapter is connected to the vehicle.<br/>When {{{model|FMB1YX}}} is connected to LV-CAN200 or ALL-CAN300, user can see all information that is received from the vehicle in configurator LVCAN section, all data are highlighted by green background color. Information in this section is automatically refreshed. CAN bus data which can be read from your car is provided in "Light or All Vehicles CAN adapter supported cars" document.<br/>The LVCAN I/O element can be configured like any other I/O element in FMB120 configurator.
+
{{{model|FMB1YX}}} shares the same USB port for connecting LV-CAN200 or ALL-CAN300 adapter and configuring device with PC.
 +
{{{model|FMB1YX}}} can be configured using “SCAN” function or “Offline Configuration”
 +
SCAN function – is in use when {{{model|FMB1YX}}} is connected to CAN adapter, then wait 10s (Note, that car engine must be started), disconnect adapter from {{{model|FMB1YX}}} , and connect PC USB cable to {{{model|FMB1YX}}} Device. It is very important not to disconnect {{{model|FMB1YX}}} from power source during this operation, because if {{{model|FMB1YX}}} is reconnected all received CAN bus data will be lost. {{{model|FMB1YX}}} remembers received data from LV-CAN200 or ALL-CAN300 and at the end of the procedure when “SCAN” button is pressed, user will see all CAN data which is sent by adapter. Enable CAN data which needs send to server and save configuration pressing “Save” button.<br/>
 +
To configure CAN data:<br/>
 +
1. In car, connect LV-CAN200 or ALL-CAN300 to CAN bus and to the {{{model|FMB1YX}}} device , wait 10 seconds. Note, that car engine must be started.<br/>
 +
2. Disconnect LV-CAN200 or ALL-CAN300 from {{{model|FMB1YX}}} , and connect PC USB cable to {{{model|FMB1YX}}} Device. It is very important not to disconnect {{{model|FMB1YX}}} from power source, because then all CAN data will be lost.
 +
[[Image:Fma_LVCAN_Connection.png|400px|center]]
   −
[[Image:Fmb120_can_conf_example.png|800px|none]]
+
CAN bus data which can be read from your car is shown in “Light or ALL Vehicles Can adapter supported cars” document. <br/>
 
+
<br/>
When using offline configuration method user can select which CAN data will be read from LV-CAN200 or ALL-CAN300 and sent directly to the server without connection to adapter. Please note that parameters depend on vehicle manufacturer and vehicle model. For further information check "Light and All Vehicles CAN adapter supported cars” document.<br/>All information about I/O element parameters description is in section [[FMB120 I/O settings|I/O settings]].<br/>All LV-CAN200/ALL-CAN300 I/O parameters configuration settings are described in "FMB120 Protocols" document, except ALL-CAN300 bitmasks, which are described in the table below.
+
'''Offline configuration '''– user can select which CAN data will be red from LV-CAN200 or ALL-CAN300 and directly sent to server without connection to adapter. Please note that parameters depend on vehicle manufacturer and vehicle model. Please for further information check “Light and All Vehicles Can adapter supported cars” document. <br/>
 +
<br/>
 +
There are two types of operations with CAN data elements:
 +
* Monitoring of CAN bus data
 +
* CAN bus data event capturing
 +
Monitoring method is used when user wants to receive CAN data on regular basis, for example every 20 seconds.<br/>
 +
<br/>
 +
Event functionality is used to store additional AVL packet when state of CAN element is changing. For example Speed changes, low fuel level, engine temperate, etc.<br/>
 +
<br/>
 +
Send data to server field – allows enabling CAN element so it is added to the AVL data packet and sent to the server. By default, all CAN elements are disabled and FMA120 records only GPS data.<br/>
 +
<br/>
 +
[[Image:Fma_LVCAN_Info.png|700px|center]]
 +
All information about I/O element parameters description is in section [[FMA120 I/O settings|I/O settings]].<br/>All LV-CAN200/ALL-CAN300 I/O parameters configuration settings are described in "FMA120 Protocols" document, except ALL-CAN300 bitmasks, which are described in the table below.
    
{| class="wikitable"
 
{| class="wikitable"