FMB640 SMS/GPRS command list
Main Page > EOL Products > FMB640 > FMB640 Manual > FMB640 SMS/GPRS command list
All commands are case sensitive. When user tries to send SMS/GPRS message to FMB640 that operates in Deep Sleep mode, it cannot arrive to FMB640 device because the GSM/GPRS module is disabled most of the time. FMB640 will receive the SMS/GPRS message when it exits Deep Sleep mode.
If FMB640 is in GPS Sleep or Online Deep Sleep mode, sent SMS/GPRS message will arrive to the device.
Common commands
| Command | Description | Response |
|---|---|---|
| getstatus | Modem Status information. | Yes |
| getcfgtime | Date and Time of last successful configuration | Yes |
| getgps | Current GPS data and time | Yes |
| getnmeainfo | Nmea error debug sms. | Yes |
| cpureset | Reset CPU. | Yes |
| resetallprof | Reset profile FLASH to default. | Yes |
| getver | Device / Modem / Code version information. | Yes |
| getinfo | Device runtime system information. | Yes |
| deleterecords | Delete all records saved on FLASH. | Yes |
| getio | Readout digital inputs and outputs, analog inputs. | Yes |
| banlist | Banlist information. | Yes |
| crashlog | Crash log information. | Yes |
| delete_all_sms | Delete all read SMS. | Yes |
| braminfo | BatRam info. | Yes |
| getgnss | Current GNSS information. | Yes |
| resetlimits | Resets data counters. | Yes |
| readio # | Enable/disable static navigation. | Yes |
| setdigout XXXX Y1 Y2 Y3 Y4 | Set digital output. 1. # – 0 or 1 (0 - OFF or 1 – ON) for DOUT1. 2. # – 0 or 1 (0 - OFF or 1 – ON) for DOUT2. 3. # – 0 or 1 (0 - OFF or 1 – ON) for DOUT3. 4. # – 0 or 1 (0 - OFF or 1 – ON) for DOUT4. Y1 – timeout value for DOUT1 if needed (in seconds). Y2 – timeout value for DOUT2 if needed (in seconds). Y3 – timeout value for DOUT3 if needed (in seconds). Y4 – timeout value for DOUT4 if needed (in seconds). |
Yes |
| getparam # | Readout parameter value according entered ID. # - ID value. |
Yes |
| setparam #:# | Sets selected parameter value. 1.# - first ID value. |
Yes |
| setparam #:#;#:#;… | ||
| flush #,#,#,#,#,#,# | Redirects device to other server. 1.# - IMEI. |
Yes |
| Command | Description | Response |
|---|---|---|
| fc_reset | Resets fuel consumption parameters. | Yes |
| towingreact | Towing reactivation. | Yes |
| odoset:# | Set total odometer value. # - new odometer value in km. |
Yes |
| odoget | Display current odometer value. | Yes |
| Command | Description | Response |
|---|---|---|
| btgetlist # | Returns requested Bluetooth list. # - 0,1 or 2 (0 – Discovered, 1 – Paired, 2 – Connected). |
Yes |
| btscan | Starts Bluetooth scan. | Yes |
| btvisible # | Sets Bluetooth to visible with TMO. # - visibility TMO (from 1 to 255 seconds). |
Yes |
| btrelease # | Disconnects from current device and pauses auto connect functionality for TMO. # - none or TMO (from 1 to 255 seconds). |
Yes |
| btunpair # | Unpair Bluetooth device. # - all, BT address (all – unpair all devices, BT address – unpair only specified MAC address). |
Yes |
| Command | Description | Response |
|---|---|---|
| lvcansetprog # | Set program number to LV-CAN200/ ALL-CAN300 that is connected to FMB1YX. # three digit number that identity vehicle. |
Yes |
| lvcansimpletacho # | Add or remove simpletacho start byte. # - 0 or 1 (0 – don’t add start byte, 1 – add start byte). |
No |
| lvcangetprog | Get program number from LV-CAN200/ ALL-CAN300 that is connected to FMB1YX. | Yes |
| lvcangetinfo | Get information about connected LV-CAN200/ALL-CAN300. | Yes |
| lvcanclear # | Clear Total Mileage (counted), Engine Work Time (counted), Fuel Consumed (counted) parameters values. # - parameter (0 – Engine work time (counted), 1 – Fuel Consumed (counted), 2 – Vehicle Mileage (counted)).. |
Yes |
| allcanmode | Turn on ALL-CAN300 mode. | Yes |
| lvcanmode | Turn on LV-CAN200 mode. | Yes |
| lvcanfaultcodes | Read DTC fault codes. | Yes |