Wialon and EYE proximity

From Wiki Knowledge Base | Teltonika GPS

Introduction

Teltonika Eye Beacons have two new scenarios related to RSSI value. RSSI means “Received Signal Strength Indicator” and this value can be use as distance indicator, or to know if the Beacon is detected by the FM tracker.

Following sections describe Proximity and Lost & Found Scenarios.

Eye Beacon Configuration

Devices work constantly and are ready to perform out of the box. Default basic Sensor settings are set to:

  • Transmitting at 2 dBm power.
  • Data advertising at 3 second intervals.
  • Eddystone protocol

However, these parameters can be changed. Transmitting power can be set from -14dBm to 8dBm – higher transmitting power equates to a larger beacon range. Data advertising interval can be selected from the range 20ms to 10s, shorter data advertising intervals ensure a more stable signal. However, increasing power or reducing the advertising interval affects the battery life of the Eye Beacon.

EYE Beacon / BTSID1 EYE Sensor / BTSMP1
2+ years

(Tx=2 dBm; interval: 1 s)

1+ year

(Tx=2 dBm; interval: 1 s)

5+ years

(Tx=2 dBm; interval: 3 s)

2.5+ years

(Tx=2 dBm; interval: 3 s)

8+ years

(Tx=2 dBm; interval: 5 s)

4+ years

(Tx=2 dBm; interval: 5 s)

10+ years

(Tx=2 dBm; interval: 10s)

5+ years

(Tx=2 dBm; interval: 10s)

More information can be found here All configuration of the Eye Beacon will be done via EYEapp. On the app, wanted protocol can be selected, transmitting power, advertising interval and Beacon ID can be easily configured. Below is an example configuration.

Eye Beacon configuration.gif

Teltonika Configurator

Common Settings

We need to set up proper Protocol and Bluetooth settings in order to have beacons information

  1. In System Settings Enable Codec8 Extended.
  2. In Bluetooth® settings Enable Bluetooth®, set this setting as either "Enable (hidden)" or "Enable (visible)", otherwise Bluetooth® will be disabled.

Proximity Scenario

EYE beacon Proximity events is a functionality which creates three different types of records, depending on the captured Beacons RSSI level. This functionality is only supported with Teltonika EYE beacons. Proximity events consist of near, away and lost events:

  • When EYE beacon RSSI level is below the first configured threshold, the beacon will be added to Near Beacon Record (AVL ID: 10828)
  • When EYE BEACON RSSI level is between the second and first configured threshold, beacon is added to Away Beacon record (AVL ID: 10829)
  • When EYE Beacon RSSI level is lower than the second configured threshold, beacon is added to Lost Beacon record (AVL ID: 10831). In the case of EYE Beacon disappearing from the environment and not being detected by the FM tracker anymore, the beacon will be added to Lost Beacon record and will be removed from Beacon list.

Event modes

  • Disabled – Record generating is disabled for the selected range
  • Periodic – Records will be periodically generated for the selected range, according to the configured record period on move or on stop value.
  • On Change – Records will be generated as soon as the Eye Beacon number changes for the selected range.

Averaging Timeout

This parameter specifies how long it will take current RSSI value to reach new RSSI value. For example, current EYE Beacon RSSI value is -40 dBm. FMB captures same EYE Beacon with RSSI value of -60 dBm. If averaging timeout is configured to be 10 seconds, it will take 10 seconds for RSSI value to reach -60 dBm from -40 dBm. Keep in mind that this is assuming perfect conditions and subsequent EYE Beacon RSSI.

Lost & Found Scenario

Lost & found.png

Purpose of this functionality is to periodically generate records with all EYE Beacon list (AVL ID: 10828) and create eventual On Change records only when EYE Beacon is lost (AVL ID: 10831) or found (AVL ID: 10829).

Lost and Found Beacon records only include EYE Beacon which was lost or found, not the full Beacon list.

  • If multiple EYE Beacons were found or lost at the same time, multiple will be included into the record.
  • If Visible Beacon List is enabled, Beacon records containing the list of visible beacons will be generated according to the configured period parameters Record Period on Move and Record Period on Stop

Advanced Beacon protocol is being used to send Lost & Found records.

Note:Same AVL ID’s as for Proximity events are being used, since two features cannot work at the same time.

  • AVL ID: 10828 Visible Beacon List (periodic)
  • AVL ID: 10829 Found Beacon List (On Change)
  • AVL ID: 10831 Lost Eye Beacon List (On Change)

Parsing Data

Proximity Parsing

Unparsed data
Received data in hexadecimal stream:

000000000000004b8e010000018368952793000f0e54fc209ab05800b300b40e00002a4f000100000000000000000001
2a4f001e011c0001a40110eb47706aa38255aa96f21a154e2d00550d01000e020bd6010000823f

AVL Data Packet
AVL Data Packet Part HEX Code Part Decoded
Zero Bytes 00 00 00 00
Data Field Length 00 00 00 BD 189 bytes
Codec ID 8E Codec8 Extended
Number of Data 1 (Number of Total Records) 01
AVL DATA Timestamp 00 00 01 83 68 95 27 93 (GMT: Tuesday, 18 June 2019 08:25:22.001)
Priority 00
Longitude 0f 0e 54 fc
Latitude 20 9a b0 58
Altitude 00 b3
Angle 00 b4
Satellites 0e
Speed 00 00
Event IO ID 2a 4f (10831)
N of Total ID 00 01
N1 of One Byte IO 00 00
N2 of Two Bytes IO 00 00
N4 of Four Bytes IO 00 00
N8 of Eight Bytes IO 00 00
NX of X Bytes IO 00 01
N’th IO ID - AVL ID. 2a 4f (10831)
Length of Variable Length IO 00 1e (30 bytes)
Value of Variable Length IO 10831 011c0001a40110eb47706aa38255aa96f21a154e2d00550d01000e020bd6
Number of Data 2 (Number of Total Records) 01
CRC-16 00 01 2a 4f