| Line 111: |
Line 111: |
| | ==== How to configure FM device for reading data from EYE sensor with standard Teltonika configurator(advanced mode)? ==== | | ==== How to configure FM device for reading data from EYE sensor with standard Teltonika configurator(advanced mode)? ==== |
| | Please follow the steps in EYE Sensor wiki page: https://wiki.teltonika-gps.com/view/EYE_SENSOR_/_BTSMP1#Teltonika_configurator_.28standard_functionality_.2F_advanced_mode.29 | | Please follow the steps in EYE Sensor wiki page: https://wiki.teltonika-gps.com/view/EYE_SENSOR_/_BTSMP1#Teltonika_configurator_.28standard_functionality_.2F_advanced_mode.29 |
| − |
| |
| − | ===<big>Value-adding Features</big>===
| |
| − |
| |
| − | ==== What is hibernated mode? ====
| |
| − | Hibernated mode means that the EYE device is OFF when shipping from the factory, preserving battery life.
| |
| − | PLEASE NOTE that EYE devices are available in two modes: factory-activated (ON) or Hibernated (OFF). You may order the device version which better suits your needs.
| |
| − |
| |
| − | ==== How to activate hibernated eye device? ====
| |
| − |
| |
| − | Attach any magnet to sleeping device and wait for LED to blink.
| |
| − | <br>'''NOTE: ANY MAGNET CAN BE USED'''
| |
| − | <br>[[File:520746 Magnet EYE gif v1.6-min.gif|frameless|684x684px]]
| |
| − | <br>Now device is discoverable, scannable, connectable via BLE.
| |
| − |
| |
| − | ==== How to put the device back to sleep (Hibernation)? ====
| |
| − |
| |
| − | If you want to put the EYE device back to sleep after accidental activation or simply pause its use, you may do that.
| |
| − | <br>Step 1. While connected and in overview tap "Send device to sleep":
| |
| − | <br>Step 2. Confirm your selection:
| |
| − | <br>Step 3. Wait for EYE App to disconnect:
| |
| − | <br>[[File:Send To Sleep.png|frameless|300x300px]][[File:Send To Sleep Confirm.png|frameless|300x300px]][[File:Send To Sleep Disconnect.png|frameless|300x300px]]
| |
| − |
| |
| − | ==== Which eye devices can I put back to sleep (Hibernation)? ====
| |
| − |
| |
| − | You may put back to sleep:
| |
| − | <br>1. All EYE Sensors with firmware version starting from 1.2.9.R.8.
| |
| − | 2. New EYE Beacons WITH ‘Hibernate’ feature. It is not available for non-Hibernate edition Beacons due to hardware limitations.
| |
| − |
| |
| − | ==== What's the value of hibernation? ====
| |
| − |
| |
| − | Hibernated versions of EYE devices simplify stock management for our partners while maximizing battery life. For example, it helps in such situations:
| |
| − | <br>1. Our partners want to have EYE devices ready and available to deploy at any moment with full battery capacity, delivering the fastest possible service and this way increasing their competitive advantage;
| |
| − | 2. Our partners order a little too many devices for a specific project, and then it may take a month or a few to deploy them for different projects. That way they may deploy EYE devices with full battery capacity for further projects as well.
| |
| | | | |
| | ===<big>Questions about Protocols</big>=== | | ===<big>Questions about Protocols</big>=== |
| Line 204: |
Line 171: |
| | | | |
| | [[File:MAGNET TRAILER MOUNTING.png|frameless|676x676px]] | | [[File:MAGNET TRAILER MOUNTING.png|frameless|676x676px]] |
| − | '''How to identify pitch/roll directions?''' | + | |
| | + | ==== '''How to identify pitch/roll directions?''' ==== |
| | Please see attached image: | | Please see attached image: |
| | [[File:PITCH ROLL.png|frameless|684x684px]] | | [[File:PITCH ROLL.png|frameless|684x684px]] |
| | | | |
| | [[Category:Sensors]] | | [[Category:Sensors]] |
