FMC650 Bluetooth® 4.0 settings

Main Page > Professional Trackers > FMC650 > FMC650 Configuration > FMC650 Bluetooth® 4.0 settings

Bluetooth 4.0 settings

FMC650 offers Bluetooth 4.0 (Bluetooth Low Energy, also referred as BLE) functionality.

Configurable parameters:

  • Update frequency – changes sensor's temperature/humidity/battery voltage data update frequency.
    Minimum value: 30 s, maximum value: 65535 s, default value: 120.
  • BLE Scan Duration - Sensors data reading time.
    Minimum value: 5 s, maximum value: 120 s, default value: 60.
  • Scan retries until error - Configured scan retries, to show the Error Value '3000' - sensor disconnected.
  • Non Stop Scan - Enabled Non Stop Scan feature, the device will try to scan for the sensors all the time if any of them are configured.
  • Working mode – Bluetooth connection mode. Disabled: Bluetooth 4.0 connection will not be used. TZ-BT04/05/05B sensor: this Bluetooth connection will be used to communicate with TZ-BT04/05/05B sensor. Advanced - It allows to gather data from BLE device‘s broadcast packets regardless of what data packing protocol is used.

Configuration modes

Non Stop Scan Enabled.

In Configurator when Non Stop sensor scans is active update frequency & scan retries until error will be hidden. Although BLE scan duration will still be active because it is important for btgetlist SMS command.


Non Stop Scan Disabled, Scan period is selected manually.

From the picture above, the Scan time period will be selected from two sources, BLE Scan Duration - the time when sensors are scanned and the Update frequency - The time when the sensor information is packed as the AVL Data record.

For example:

Update frequency - 120 seconds.

BLE Scan Duration - 60 Seconds

Device will start the first scan after 120 seconds and will scan nearby BLE devices for 60 seconds to update configured sensor data. The sensor data will be updated every 120 seconds. Update Frequency is counted even while a scan is performed.

Update frequency period passes. 120 seconds -> 0 seconds, a 60 second scan is initiated. Update Frequency countdown is restarted (countdown from configured value to 0) while the scan (according to the BLE Scan duration parameter) is performed.

Advanced Mode


When Advanced mode is selected a table with configurable parameters will appear:


  • The table has 9 types of parameters:
    1. Type – EIR data type. This parameter will indicate which type to look for and work with. Note: We have also added type with value 0xFE which will indicate to work with a whole data packet and not just a single data type.
    2. Data Offset – start index of data we are interested in.
    3. Data Size – size of the data we are interested in.
    4. Action – two actions are possible: Match and Save. Match means that we want to perform a validation of certain data. Save means that we want to get certain data and later save it to an AVL record.
    5. IO – tells which IO element's data will be saved to. Possible choices for IO elements will be described later in the chapter. Used only with Save action.
    6. Match – hex string to be matched with BLE sensor data. Used only with Match action.
    7. Endianness – endianness of data: little endian (ex. 0x1122) or big endian (ex. 0x2211). Used only with Save action.
    8. Multiplier – value to be used to multiply output data. Used only with Save action.
    9. Offset – value to be added to output data. Used only with Save action.

IO elements choices

Name Connection #1 AVL ID Connection #2 AVL ID Connection #3 AVL ID Connection #4 AVL ID
None - - - -
Temperature 701 702 703 704
Battery 705 706 707 708
Humidity 709 710 711 712
Fuel 270 273 276 279
Luminosity 717 718 719 720
Fuel LLS Fuel 721 722 723 724
Fuel Frequency 725 726 727 728
Custom1 713 714 715 716
Custom2 729 730 731 732
Custom3 733 734 735 736
Custom4 737 738 739 740
Custom5 741 742 743 744

Supported Sensors List

This list shows the supported BLE sensors and where their Presets can be found in the configurator to use those sensors with FMB devices. The prests and sensors have been fully tested by Teltonika and are confirmed to work properly.

While following the steps showed in the images below, you can find the supported sensors in our Configurator.

In the Configurator, find the Bluetooth 4.0 Settings menu, select the advanced sensors mode which was mentioned before. The following window should appear.


At the top right corner, you should see the following Buttons, press on the first one from the left.

After the named Button was pressed the list with all supported sensors and the configuration presets should appear.


Select your sensor and click load. The correct configuration and recommended settings will appear in the configuration.

The supported sensors are listed below:

  • BLE TPMS -Tire Pressure Monitoring System.
  • Efento Humidity BLE sensors (version 2.2 and 4 presets)
  • ELA ANG (Angle)
  • ELA MOV AG (Movement and Angle)
  • ELA PUCK ID (ID)
  • ELA RHT (Temperature and Humidity)
  • ELA T (Temperature)
  • ELA MOV MAG (Movement Magnetic)
  • Escort Fuel BLE sensors
  • Escort luminosity BLE sensors
  • Escort Temperature BLE sensors
  • TELTONIKA EYE BEACON
  • TELTONIKA EYE SENSOR
  • S1 BLE Motion, Humidity and Temperature Sensors
  • Technoton DUT-E S7 Fuel Level Sensor
  • Technoton DFM D S7 Differential Fuel Flow Meter
  • Technoton GNOM DDE/DP S7 Axle Load Sensors
  • TZ-BT04 Temperature and Humidity Sensors
  • TZ-BT05 Temperature and Humidity Sensors

Visual demonstration

Here is a visual demonstration of Bluetooth 4.0 sensors in a cold storage truck.


FMB Family Bluetooth 4.0 support


Devices that are listed in table below shows which device model has Bluetooth 4.0 hardware installed. If your device is manufactured before the day shown in the list it means that this model does not have Bluetooth functionality or it has an older version installed. The date shown in the table depends on when hardware production has started, but not when first lot was sold.

Device Model BT 4.0 manufacture starting date
FM30012018.01
FMB010 2018.04
FMB001 2018.04
FMB900 2018.08
FMB920 2018.07
FMB964 2019.07
FMB120 2018.01
FMB122 2017.11
FMB125 2017.11
FMB130All versions
FMB140All versions
FMU125FW is on release, All versions
FMU126FW is on release, All versions
FMU130FW is on release, All versions
FMM125FW is on release, All versions
FMM130FW is on release, All versions
FMM0YXFW is on release, All versions
FMB202All versions
FMB204All versions
FMB208All versions
FMC640All versions

Disclaimer

 


If you are not using Bluetooth, please consider turning it off or change Bluetooth PIN to remove potential risks.

If you are using Bluetooth we strongly recommend using AES encryption for enhanced security.