Changes

==Disclaimer==

==Disclaimer==

[[File:Alert.png|left|link=]] <br> If you are not using Bluetooth, '''please consider turning it off''' or '''change Bluetooth PIN''' to remove potential risks.

[[File:Alert.png|left|link=]] <br> If you are not using Bluetooth®, '''please consider turning it off''' or '''change Bluetooth® PIN''' to remove potential risks.

If you are using Bluetooth we strongly recommend '''using AES encryption''' for enhanced security.

If you are using Bluetooth® we strongly recommend '''using AES encryption''' for enhanced security.

=Sensors=

=Sensors=

TAT100 has a BLE connectionless devices reading feature that can be configured in the '''Bluetooth''' tab. When '''Sensors''' mode is selected a table with configurable parameters will appear. Currently to the TAT100 device up to '''4 sensors''' can be connected.  

TAT100 has a BLE connectionless devices reading feature that can be configured in the '''Bluetooth®''' tab. When '''Sensors''' mode is selected a table with configurable parameters will appear. Currently to the TAT100 device up to '''4 sensors''' can be connected.  

[[Image:TAT100_BLE_Sensor_configuration_v3.png|250px|{{{general|size}}}|right]]

[[Image:TAT100_BLE_Sensor_configuration_v3.png|250px|{{{general|size}}}|right]]

<br>'''BLE Feature:'''<br>

<br>'''BLE Feature:'''<br>

<br><code>None</code> – Bluetooth functionality will be disabled. <br>

<br><code>None</code> – Bluetooth® functionality will be disabled. <br>

<code>Sensors</code> – Enables Bluetooth functionality for sensors. <br>

<code>Sensors</code> – Enables Bluetooth® functionality for sensors. <br>

'''Update frequency''' – how often BLE scanning will run. <br>

'''Update frequency''' – how often BLE scanning will run. <br>

'''To ENABLE backup feature on TAT100 device:'''

'''To ENABLE backup feature on TAT100 device:'''

# <code>Bluetooth</code> → select <code>Backup Tracker</code><br>

# <code>Bluetooth®</code> → select <code>Backup Tracker</code><br>

# Enter main device (FMBxxx/TFT100/TST100/GH5200/TMT250) IMEI<br>

# Enter main device (FMBxxx/TFT100/TST100/GH5200/TMT250) IMEI<br>

# Set <b>Update frequency</b> to <b>3600</b> (s) – <i>We do not recommend to set values below <b>1800</b> sec. in this field, as it will shorten the battery life.</i><br>

# Set <b>Update frequency</b> to <b>3600</b> (s) – <i>We do not recommend to set values below <b>1800</b> sec. in this field, as it will shorten the battery life.</i><br>

[[File:TAT100_Bluetooth_Backup_v2.png|center|400px]]

[[File:TAT100_Bluetooth®_Backup_v2.png|center|400px]]

'''To ENABLE backup feature on FMBXXX/TFT100/TST100/GH5200/TMT250 devices:'''

'''To ENABLE backup feature on FMBXXX/TFT100/TST100/GH5200/TMT250 devices:'''

#<code>Bluetooth</code> → <code>BT Radio</code> set to <code>Enable(visible)</code><br><br>[[File:BT ONN.jpg|center|500px]]<br>

#<code>Bluetooth®</code> → <code>BT Radio</code> set to <code>Enable(visible)</code><br><br>[[File:BT ONN.jpg|center|500px]]<br>

#ENABLE backup feature on:

#ENABLE backup feature on:

##<b>TFT100 | TST100 | GH5200 | TMT250</b> devices<br><code>Bluetooth 4.0</code> → <code>Backup Tracker</code> set to <code>Enabled</code><br><br>[[File:TAT100_bluetooth_backup_enable.png|center|700px]]<br>

##<b>TFT100 | TST100 | GH5200 | TMT250</b> devices<br><code>Bluetooth® 4.0</code> → <code>Backup Tracker</code> set to <code>Enabled</code><br><br>[[File:TAT100_bluetooth_backup_enable.png|center|700px]]<br>

##<b>FMBXXX</b> devices<br>Instructions on how to configure the FMBXXX device can be found [https://wiki.teltonika-gps.com/view/FMC130_Bluetooth_4.0_settings#Backup_Tracker here].

##<b>FMBXXX</b> devices<br>Instructions on how to configure the FMBXXX device can be found [https://wiki.teltonika-gps.com/view/FMC130_Bluetooth®_4.0_settings#Backup_Tracker here].

==DEVICE RECOGNITION CHECK USING TERMINAL==  

==DEVICE RECOGNITION CHECK USING TERMINAL==