ATC700 Teltonika Data Sending Parameters ID

Teltonika devices send data in packets that follow a specific structure, as defined on our Codec page. Each parameter in a record is identified by a Data Sending ID (AVL ID). These IDs are used to extract the correct values from the hexadecimal data during processing on the server side.

This page lists all available AVL IDs for ATC700. Differences in AVL IDs between the FT and legacy FMB platforms are described on the dedicated page. Property IDs in the AVL packet that differ between platforms are marked in bold.

AVL IDs are grouped into the following parameter groups:

Permanent I/O elements

---

Property ID in AVL packet	Property Name	Bytes	Type	Min Value	Max Value	Multiplier	Units	Description	Parameter Group
16	Total Odometer	4	Unsigned	0	2147483647	-	m	Virtual odometer value	Permanent I/O elements
17	Axis X	2	Signed	-8000	8000	-	mg	Axis X value	Permanent I/O elements
18	Axis Y	2	Signed	-8000	8000	-	mg	Axis Y value	Permanent I/O elements
19	Axis Z	2	Signed	-8000	8000	-	mg	Axis Z value	Permanent I/O elements
21	GSM Signal	1	Unsigned	0	5	-	-	Value in range 1-5	Permanent I/O Elements
67	Battery Voltage	2	Unsigned	0	65535	-	mV	Voltage	Permanent I/O elements
68	Battery Current	2	Unsigned	0	65535	-	mA	Current	Permanent I/O elements
69	GNSS Status	1	Unsigned	0	3	-	-	0 - GNSS OFF 1 - GNSS ON with fix 2 - GNSS ON without fix 3 - GNSS sleep	Permanent I/O elements
70	PCB temperature	2	Signed	-550	1150	-	°C	Degrees	Permanent I/O elements
113	Battery level	1	Unsigned	0	100	-	°C	Battery capacity level	Permanent I/O elements
181	GNSS PDOP	2	Unsigned	0	500	-	m	GNSS position dilution of precision. Normal PDOP is below 3 – the lower the number, the more accurate reported location is.	Permanent I/O elements
182	GNSS HDOP	2	Unsigned	0	500	-	m	GNSS horizontal dilution of precision. Normal HDOP is below 2 – the lower the number, the more accurate reported location is.	Permanent I/O elements
199	Trip Odometer	4	Unsigned	0	2147483647	-	m	Trip distance value calculated by GNSS	Permanent I/O elements
205	GSM Cell ID	4	Unsigned	0	2147483647	-	-	GSM base station ID	Permanent I/O elements
206	GSM Area Code	2	Unsigned	0	65535	-	-	Location Area code (LAC), it depends on GSM operator. It provides unique number which assigned to a set of base GSM stations	Permanent I/O elements
237	Network Type	1	Unsigned	0	1	-	-	0 - 3G 1 - GSM 2 - 4G 3 - LTE CAT M1 4 - LTE CAT NB1 99 - Unknown	Permanent I/O elements
240	Movement	1	Unsigned	0	1	-	-	0 – Movement Off 1 – Movement On	Permanent I/O Elements
241	GSM operator code	4	Unsigned	0	4294967295	-	-	Currently used GSM Operator code	Permanent I/O elements
303	Instant Movement	1	Unsigned	0	1	-	-	Logic: 0/1 returns movement value	Permanent I/O elements
386	Time from last fix	2	Unsigned	0	65535	-	sec	-	Permanent I/O elements
641	ICCID	22	ASCII	0	22	-	-	Value of SIM ICCID (Integrated circuit card identification number)	Permanent I/O elements
1148	Connectivity quality	4	Unsigned	0	2147483647	-	dBm	Provides detailed signal quality information in LTE, eMTC (CAT-Mx) and NB-IoT modes: RSSI (byte 0): 0 - 255 in dBm (negative values) RSRP (byte 1): 0 - 255 in dBm (negative values) SINR (byte 2): 0 - 250 which translates to -20dB to +30dB (1/5th of dB) RSRQ (byte 3): 0 - 255 in dB (negative values)	Permanent I/O elements
13361	Incoming call detection	1	Unsigned	0	1	-	-	0 – No incoming call 1 – An incoming call is in progress	Permanent I/O elements
1149	Current LTE Band	1	Unsigned	0	1	-	-	Provides information about LTE BAND the device is connected to. Possible bands in LTE, eMTC (CAT-Mx) and NBIoT modes: 1 - 85: LTE BAND 1 - LTE BAND 85 0: No LTE Band available.	Permanent I/O elements
11399	Time to First Fix	1	Unsigned	0	1	-	-	Time taken in seconds until the first GNSS fix after device is reset.	Permanent I/O elements

Eventual I/O elements

Property ID in AVL packet	Property Name	Bytes	Type	Min Value	Max Value	Multiplier	Units	Description	Parameter Group
236	Alarm	1	Unsigned	0	1	-	-	0 – Reserved 1 – Alarm event occurred	Eventual I/O elements