FTC881 Teltonika Data Sending Parameters ID

From Teltonika Telematics Wiki
Main Page > Fast & Easy Trackers > FTC881 > FTC881 Teltonika Data Sending Parameters ID

Teltonika devices send data in packets that follow a specific structure, as defined on our Codec page. Each parameter in a record is identified by a Data Sending ID (AVL ID). These IDs are used to extract the correct values from the hexadecimal data during processing on the server side.

This page lists all available AVL IDs for FTC881. Differences in AVL IDs between the FT and legacy FMB platforms are described on the dedicated page. Property IDs in the AVL packet that differ between platforms are marked in bold.

The document is based on firmware version 2.1.1 or newer. AVL IDs are grouped into the following parameter groups:

Permanent I/O elements


Property ID in AVL packet Property Name Bytes Type Min Value Max Value Multiplier Units Description Parameter Group
16 Total Odometer 4 Unsigned 0 2147483647 - m Virtual odometer value Permanent I/O elements
17 Axis X 2 Signed -8000 8000 - mg Axis X value Permanent I/O elements
18 Axis Y 2 Signed -8000 8000 - mg Axis Y value Permanent I/O elements
19 Axis Z 2 Signed -8000 8000 - mg Axis Z value Permanent I/O elements
21 GSM Signal 1 Unsigned 0 5 - - Value in range 1-5 Permanent I/O Elements
67 Battery Voltage 2 Unsigned 0 65535 - mV Voltage Permanent I/O elements
68 Battery Current 2 Unsigned 0 65535 - mA Current Permanent I/O elements
69 GNSS Status 1 Unsigned 0 3 - - 0 - GNSS OFF
1 - GNSS ON with fix
2 - GNSS ON without fix
3 - GNSS sleep
Permanent I/O elements
70 PCB temperature 2 Signed -550 1150 - °C Degrees Permanent I/O elements
113 Battery level 1 Unsigned 0 100 - °C Battery capacity level Permanent I/O elements
181 GNSS PDOP 2 Unsigned 0 500 - m GNSS position dilution of precision.
Normal PDOP is below 3 – the lower the number, the more accurate reported location is.
Permanent I/O elements
182 GNSS HDOP 2 Unsigned 0 500 - m GNSS horizontal dilution of precision.
Normal HDOP is below 2 – the lower the number, the more accurate reported location is.
Permanent I/O elements
199 Trip Odometer 4 Unsigned 0 2147483647 - m Trip distance value calculated by GNSS Permanent I/O elements
200 Sleep mode 1 Unsigned 0 2 - - TBA Permanent I/O elements
205 GSM Cell ID 4 Unsigned 0 2147483647 - - GSM base station ID Permanent I/O elements
206 GSM Area Code 2 Unsigned 0 65535 - - Location Area code (LAC), it depends on GSM operator. It provides unique number which assigned to a set of base GSM stations. Permanent I/O elements
237 Network Type 1 Unsigned 0 1 - - 0 - 3G
1 - GSM
2 - 4G
3 - LTE CAT M1
4 - LTE CAT NB1
99 - Unknown
Permanent I/O elements
239 Ignition 1 Unsigned 0 1 - - 0 – Ignition Off
1 – Ignition On
Permanent I/O Elements
240 Movement 1 Unsigned 0 1 - - 0 – Movement Off
1 – Movement On
Permanent I/O Elements
241 GSM operator code 4 Unsigned 0 4294967295 - - Currently used GSM Operator code Permanent I/O elements
303 Instant Movement 1 Unsigned 0 1 - - Logic: 0/1 returns movement value Permanent I/O elements
383 Accel calibration status 1 Unsigned 0 1 - - 0 - not calibrated (empty)
1 - calibrated, but not fully (present)
2 - disabled
3 - fully calibrated (full)
Permanent I/O elements
641 ICCID 22 ASCII 0 22 - - Value of SIM ICCID (Integrated circuit card identification number) Permanent I/O elements
800 External Voltage 2 Unsigned 0 4294967295 - mV Voltage Permanent I/O elements
1148 Connectivity quality 4 Unsigned 0 2147483647 - dBm Provides detailed signal quality information in LTE, eMTC (CAT-Mx) and NB-IoT modes:
RSSI (byte 0): 0 - 255 in dBm (negative values)
RSRP (byte 1): 0 - 255 in dBm (negative values)
SINR (byte 2): 0 - 250 which translates to -20dB to +30dB (1/5th of dB)
RSRQ (byte 3): 0 - 255 in dB (negative values)
Permanent I/O elements
13361 Incoming call detection 1 Unsigned 0 1 - - 0 – no incoming call
1 – an incoming call is in progress
Permanent I/O elements

Eventual I/O elements


Property ID in AVL packet Property Name Bytes Type Min Value Max Value Multiplier Units Description Parameter Group
247 Crash detection 1 Unsigned 1 6 - - 1 – crash
2 – limited crash trace (device not calibrated)
3 - limited crash trace (device is calibrated)
4 - full crash trace (device not calibrated)
5 - full crash trace (device is calibrated)
6 - crash detected (device not calibrated)
Eventual I/O elements
257 Crash trace data 1200 HEX 0 1200 - - Crash trace data Eventual I/O elements
1429 Crash average vector 8 Unsigned - - - mG Stores the average vector calculated during the crash: 2B - X axis, 2B - Y axis, 2B - Z axis, 2B - magnitude in mG. Eventual I/O elements
1430 Crash direction - Unsigned - - - - Stores the indication if the accelerometer is calibrated.
Also, indicates the direction of the crash.
1 bit (highest bit) indicates calibration status, rest of the bits indicates crash direction.
Eventual I/O elements
1431 Crash duration - Unsigned - - - - Duration of the crash event Eventual I/O elements
1432 Crash max vector 8 Unsigned - - - mG Stores the max vector calculated during the crash: 2B - X axis, 2B - Y axis, 2B - Z axis, 2B - magnitude in mG. Eventual I/O elements
255 Over Speeding 1 Unsigned 0 255 - km/h At over speeding start km/h, at over speeding end km/h Eventual I/O elements
250 Trip 1 Unsigned 0 1 - - 0 – trip stop
1 – trip start
2 – Business Status
3 – Private Status
4-9 – Custom Statuses
Eventual I/O elements
253 Eco driving type 1 Unsigned 1 3 - - 1 – harsh acceleration
2 – harsh braking
3 – harsh cornering
Eventual I/O elements
254 Eco driving value 1 Unsigned 0 255 acc and braking: 0.01 G
or
rad
Depending on Eco driving type: if harsh acceleration or braking – g*100 (value 123 -> 1.23g). If Eco driving source is „GPS“ – harsh cornering value is rad/s*100. If source is „Accelerometer“ – g*100. Eventual I/O elements
251 Excessive idling 1 Unsigned 0 1 - - 0 – moving
1 – idling
Eventual I/O elements
249 Network jamming detection 1 Unsigned 0 1 - - Logic: 0/1 Eventual I/O elements
252 Unplug detection 1 Unsigned 0 1 - - 0 – battery present
1 – battery unplugged
Eventual I/O elements
175 Auto geofence 1 Unsigned 0 1 - - 0 – target left zone
1 – target enetered zone
Eventual I/O elements
246 Towing detection 1 Unsigned 0 1 - - 0 – steady
1 – towing
Eventual I/O elements
358 Custom scenario 1 1 Unsigned 0 1 - - - Eventual I/O elements
359 Custom scenario 2 1 Unsigned 0 1 - - - Eventual I/O elements
360 Custom scenario 3 1 Unsigned 0 1 - - - Eventual I/O elements