720
edits
Changes
mLine 58:
Line 58: − + − + − + + + + + + + + − [[Image:FMB120_lv-can200_pinout.png|800px|center]] − [[Image:FMB120_all-can300_pinout.png|800px|center]]
no edit summary
SIMPLE-CAN works in the '''listening mode only''', so that not all the data available on the CAN-BUS may be received using this solution. '''The device automatically sets CAN L/H polarity''', but the calibration has to be always performed during installation process. Connection of previously calibrated unit to another car needs new calibration because the reader '''automatically adjusts signal level and speed''' to different CAN buses. The device also '''automatically adapts''' to the found '''noise level'''.
SIMPLE-CAN works in the '''listening mode only''', so that not all the data available on the CAN-BUS may be received using this solution. '''The device automatically sets CAN L/H polarity''', but the calibration has to be always performed during installation process. Connection of previously calibrated unit to another car needs new calibration because the reader '''automatically adjusts signal level and speed''' to different CAN buses. The device also '''automatically adapts''' to the found '''noise level'''.
[[Image:Fmb120_simplecan_pinout.png|800px|center]]
[[Image:Fmb120_simplecan_pinout.png|800px]]
<br>
When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.
When power supply is connected, the LED shines continuously. It means that device is waiting for calibration. '''Calibration process''' has to be carried out when CAN-BUS twisted pair is tightened on SIMPLE-CAN and when ignition is ON. Please press the switch briefly and wait for the LED to start blinking every second. Automatic calibration process takes up to 10 seconds depending on the vehicle's model. Correct calibration process is confirmed by LED starting to blink every 2 seconds (when the CAN-BUS is active). When the CAN-BUS enters sleep mode, SIMPLE-CAN device also enters sleep mode and takes 1.6mA @ 12V. In the sleep mode LED does not shine. If after calibration process LED shines continuously, it means that device is not calibrated yet, CAN-BUS transmission has failed or ignition during calibration was not ON.
==Connecting {{{model|FM36YX}}} CAN adapters ALL-CAN300 and LV-CAN200==
==Connecting {{{model|FM36YX}}} CAN adapters ALL-CAN300 and LV-CAN200==
Connect LV-CAN200/ALL-CAN300 Pin 5 to {{{model|FM36YX}}} Pin 12 (INPUT 5) or Pin 6 (INPUT 6) and connect light vehicle CAN adapter to other end of the cable.<br/>Connect CAN adapter Pin 1 and Pin 2 to car's CAN bus. CAN interface location of the supported light vehicle is described on mounting scheme.<br/>Connect car power supply lines to Pin 3 positive, Pin 4 negative.<br/>Pin 9 and 10 connections are optional depending on the exact car model.<br/>For exact pinout see the sticker of light vehicle CAN adapter.
FM3612 connection with CAN adapter is different than with other FM devices, when connecting ALL-CAN300 and LV-CAN200 adapters. FM3612 has closed USB connector and CAN adapter is connected with INPUT 5 and INPUT 6 wires as shown in figure below.
<br>
[[File:LV-CAN200 ALL-CAN300 Adapter connection cable pinout.png|800px]]
<br>
Connect LV-CAN200/ALL-CAN300 Pin 5 to {{{model|FM36YX}}} Pin 12 (INPUT 5) or Pin 6 (INPUT 6) and connect light vehicle CAN adapter to other end of the cable.<br/>
Connect CAN adapter Pin 1 and Pin 2 to car's CAN bus. CAN interface location of the supported light vehicle is described on mounting scheme. Connect car power supply lines to Pin 3 positive, Pin 4 negative.<br/>
Pin 9 and 10 connections are optional depending on the exact car model.<br/>For exact pinout see the sticker of light vehicle CAN adapter.<br/>
{| class="wikitable" style="border-style: solid; border-width: 0px"
{| class="wikitable" style="border-style: solid; border-width: 0px"
