0
edits
Changes
Template:FMB2 Mounting recommendations (view source)
Revision as of 11:57, 24 October 2018
, 11:57, 24 October 2018no edit summary
=='''Mounting recommendations'''==
<font size="+1"><span style=color:#F49E21> 1. </span> Connecting wires </font>
*<big>Connecting wires</big>
**Wires should be connected while the module is not plugged in.
**Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or moving objects should be kept away from the wires.
**There should be no exposed wires. If factory isolation was removed while connecting the wires, the isolation material should be applied.
**If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be loose.
**Wires cannot be connected to the board computers or control units.
*<big>Connecting power source</big>
**Be sure that after the car computer goes to sleep mode, power might be still available on the power wires. Depending on the car model, this may happen in 5 to 30 minutes period.
**When the module is connected, measure the voltage again to make sure it did not decrease.
**It is recommended to connect to the main power cable in the fuse box.
**3 A, 125 V external fuse shall be used.
*<big>Connecting ignition wire</big>
**Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
**Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
**Check if power is still available when you turn off any of vehicles devices.
**Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
*<big>Connecting ground wire</big>
**Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
**If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
**For better contact scrub paint from the spot where loop is going to be connected.
=='''{{{model|FMB2YX}}} installation instruction'''==
{{Template:FMB2YX_Installation_instruction|model={{{model|FMB2YX}}}}}
{{Template:FMB2YX_Installation_instruction|model={{{model|FMB2YX}}}}}
==<span style=color:#FF0000>'''PAY ATTENTION!'''</span>==
Connecting the power supply must be carried out in a
Connecting the power supply must be carried out in a
very low impedance point on-board vehicle network. These points in the car are
very low impedance point on-board vehicle network. These points in the car are
car is unacceptable, as static and dynamic potentials on the line GND will be
car is unacceptable, as static and dynamic potentials on the line GND will be
unpredictable, which can lead to unstable {{{model|FMB20X}}} and even its failure.
unpredictable, which can lead to unstable {{{model|FMB20X}}} and even its failure.
==<span style=color:#FF0000>'''Safety information'''</span>==
This message contains information on how to operate {{{model|FMB20X}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/>
This message contains information on how to operate {{{model|FMB20X}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/>
The device uses SELV limited power source. The device uses a 6 V...30 V DC power supply.
The device uses SELV limited power source. The device uses a 6 V...30 V DC power supply.
Before dismounting the device from the vehicle, the connection cables must be disconnected.<br/>
Before dismounting the device from the vehicle, the connection cables must be disconnected.<br/>
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.<br/>
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.<br/>
The device {{{model|FMB20X}}} is not designed as a navigational device for boats.<br/></font>
The device {{{model|FMB20X}}} is not designed as a navigational device for boats.<br/>
==<span style=color:#104996>'''Precautions'''</span>==
{| class="wikitable" style="border-style: solid; border-width: 0px"
{| class="wikitable" style="border-style: solid; border-width: 0px"
|+
|+