0
edits
Changes
Template:FMB9 Mounting recommendations (view source)
Revision as of 14:51, 24 October 2018
, 14:51, 24 October 2018no edit summary
=='''Mounting recommendations'''==
<font size="+2"><span style=color:#F49E21> 1. </span> Connecting wires </font>
* <big>Connecting wires</big>
** Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
* Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
** The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
* The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
** If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
* If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
** Wires cannot be connected to the board computers or control units.
* Wires cannot be connected to the board computers or control units.
* <big>Connecting power source</big>
</font>
** Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in 5 to 30 minutes period.
** When module is connected, measure voltage again to make sure it did not decrease.
** It is recommended to connect to the main power cable in the fuse box.
** Use 3A, 125V external fuse.
* <big>Connecting ignition wire</big>
** Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
** Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available).
** Check if power is still available when you turn off any of vehicles devices.
** Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on, may be chosen.
* <big>Connecting ground wire</big>
** Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
** If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
** For better contact scrub paint from the spot where loop is going to be connected.
==<span style=color:#FF0000>'''Safety information'''</span>==
This message contains information on how to operate {{{model|FMB1YX}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/>
This message contains information on how to operate {{{model|FMB1YX}}} safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!<br/>
The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is {{{voltage|+6..+30}}} V DC.<br/>
The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is {{{voltage|+6..+30}}} V DC.<br/>
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.<br/>
The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 60950-1 standard.<br/>
The device {{{model|FMB1YX}}} is not designed as a navigational device for boats.<br/>
The device {{{model|FMB1YX}}} is not designed as a navigational device for boats.<br/>
===<span style=color:#104996>Precautions</span>===
{| class="wikitable" style="border-style: solid; border-width: 0px"
{| class="wikitable" style="border-style: solid; border-width: 0px"
|+
|+
| style="text-align: left; background: #F6F6FB;" | Installation and/or handling during a lightning storm is prohibited.
| style="text-align: left; background: #F6F6FB;" | Installation and/or handling during a lightning storm is prohibited.
|}
|}
